power.cpp

/**
 * Marlin 3D Printer Firmware
 * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
 * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */

/**
 * power.cpp - power control
 */

#include "../inc/MarlinConfig.h"

#if ENABLED(AUTO_POWER_CONTROL)

#include "power.h"
#include "../module/temperature.h"
#include "../module/stepper/indirection.h"
#include "../MarlinCore.h"

#if BOTH(USE_CONTROLLER_FAN, AUTO_POWER_CONTROLLERFAN)
  #include "controllerfan.h"
#endif

Power powerManager;

millis_t Power::lastPowerOn;

bool Power::is_power_needed() {
  #if ENABLED(AUTO_POWER_FANS)
    FANS_LOOP(i) if (thermalManager.fan_speed[i]) return true;
  #endif

  #if ENABLED(AUTO_POWER_E_FANS)
    HOTEND_LOOP() if (thermalManager.autofan_speed[e]) return true;
  #endif

  #if BOTH(USE_CONTROLLER_FAN, AUTO_POWER_CONTROLLERFAN)
    if (controllerFan.state()) return true;
  #endif

  if (TERN0(AUTO_POWER_CHAMBER_FAN, thermalManager.chamberfan_speed))
    return true;

  // If any of the drivers or the bed are enabled...
  if (X_ENABLE_READ() == X_ENABLE_ON || Y_ENABLE_READ() == Y_ENABLE_ON || Z_ENABLE_READ() == Z_ENABLE_ON
    || TERN0(HAS_HEATED_BED, thermalManager.temp_bed.soft_pwm_amount > 0)
    #if HAS_X2_ENABLE
      || X2_ENABLE_READ() == X_ENABLE_ON
    #endif
    #if HAS_Y2_ENABLE
      || Y2_ENABLE_READ() == Y_ENABLE_ON
    #endif
    #if HAS_Z2_ENABLE
      || Z2_ENABLE_READ() == Z_ENABLE_ON
    #endif
    #if E_STEPPERS
      #define _OR_ENABLED_E(N) || E##N##_ENABLE_READ() == E_ENABLE_ON
      REPEAT(E_STEPPERS, _OR_ENABLED_E)
    #endif
  ) return true;

  HOTEND_LOOP() if (thermalManager.degTargetHotend(e) > 0) return true;
  if (TERN0(HAS_HEATED_BED, thermalManager.degTargetBed() > 0)) return true;

  #if HAS_HOTEND && AUTO_POWER_E_TEMP
    HOTEND_LOOP() if (thermalManager.degHotend(e) >= AUTO_POWER_E_TEMP) return true;
  #endif

  #if HAS_HEATED_CHAMBER && AUTO_POWER_CHAMBER_TEMP
    if (thermalManager.degChamber() >= AUTO_POWER_CHAMBER_TEMP) return true;
  #endif

  return false;
}

void Power::check() {
  static millis_t nextPowerCheck = 0;
  millis_t ms = millis();
  if (ELAPSED(ms, nextPowerCheck)) {
    nextPowerCheck = ms + 2500UL;
    if (is_power_needed())
      power_on();
    else if (!lastPowerOn || ELAPSED(ms, lastPowerOn + SEC_TO_MS(POWER_TIMEOUT)))
      power_off();
  }
}

void Power::power_on() {
  lastPowerOn = millis();
  if (!powersupply_on) {
    PSU_PIN_ON();
    safe_delay(PSU_POWERUP_DELAY);
    restore_stepper_drivers();
    TERN_(HAS_TRINAMIC_CONFIG, safe_delay(PSU_POWERUP_DELAY));
  }
}

void Power::power_off() {
  if (powersupply_on) PSU_PIN_OFF();
}

#endif // AUTO_POWER_CONTROL