diff --git a/Marlin/Conditionals_LCD.h b/Marlin/Conditionals_LCD.h
index 4b23ea3e9de769ebaef022da5261406417628788..356a61bbecc47da874550487438dc3e217a0dada 100644
--- a/Marlin/Conditionals_LCD.h
+++ b/Marlin/Conditionals_LCD.h
@@ -386,5 +386,6 @@
#define HAS_SOFTWARE_ENDSTOPS (ENABLED(MIN_SOFTWARE_ENDSTOPS) || ENABLED(MAX_SOFTWARE_ENDSTOPS))
#define HAS_RESUME_CONTINUE (ENABLED(NEWPANEL) || ENABLED(EMERGENCY_PARSER))
+ #define HAS_COLOR_LEDS (ENABLED(BLINKM) || ENABLED(RGB_LED))
#endif //CONDITIONALS_LCD_H
diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index e17a2db8a035ecc42f230e5d36b9fc8ed60fe7ee..4152d7d33e8b0d4610f2261661df6cddc9850da3 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -1514,7 +1514,23 @@
//define BlinkM/CyzRgb Support
//#define BLINKM
-// Support for an RGB LED using 3 separate pins with optional PWM
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
//#define RGB_LED
#if ENABLED(RGB_LED)
#define RGB_LED_R_PIN 34
@@ -1522,6 +1538,21 @@
#define RGB_LED_B_PIN 35
#endif
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #define PRINTER_EVENT_LEDS
+#endif
+
/*********************************************************************\
* R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas
diff --git a/Marlin/Marlin_main.cpp b/Marlin/Marlin_main.cpp
index 7500abac57a74ef59a27aeed02b6f653cc6805b3..64c0bbe368552e527cb05d2f41aed719820f057d 100644
--- a/Marlin/Marlin_main.cpp
+++ b/Marlin/Marlin_main.cpp
@@ -945,6 +945,31 @@ void servo_init() {
#endif
+#if HAS_COLOR_LEDS
+
+ void set_led_color(const uint8_t r, const uint8_t g, const uint8_t b) {
+
+ #if ENABLED(BLINKM)
+
+ // This variant uses i2c to send the RGB components to the device.
+ SendColors(r, g, b);
+
+ #else
+
+ // This variant uses 3 separate pins for the RGB components.
+ // If the pins can do PWM then their intensity will be set.
+ digitalWrite(RGB_LED_R_PIN, r ? HIGH : LOW);
+ digitalWrite(RGB_LED_G_PIN, g ? HIGH : LOW);
+ digitalWrite(RGB_LED_B_PIN, b ? HIGH : LOW);
+ analogWrite(RGB_LED_R_PIN, r);
+ analogWrite(RGB_LED_G_PIN, g);
+ analogWrite(RGB_LED_B_PIN, b);
+
+ #endif
+ }
+
+#endif // HAS_COLOR_LEDS
+
void gcode_line_error(const char* err, bool doFlush = true) {
SERIAL_ERROR_START;
serialprintPGM(err);
@@ -1129,6 +1154,19 @@ inline void get_serial_commands() {
if (card_eof) {
SERIAL_PROTOCOLLNPGM(MSG_FILE_PRINTED);
card.printingHasFinished();
+ #if ENABLED(PRINTER_EVENT_LEDS)
+ LCD_MESSAGEPGM(MSG_INFO_COMPLETED_PRINTS);
+ set_led_color(0, 255, 0);
+ #if HAS_RESUME_CONTINUE
+ KEEPALIVE_STATE(PAUSED_FOR_USER);
+ wait_for_user = true;
+ while (wait_for_user) idle();
+ KEEPALIVE_STATE(IN_HANDLER);
+ #else
+ safe_delay(1000);
+ #endif
+ set_led_color(0, 0, 0);
+ #endif
card.checkautostart(true);
}
else if (n == -1) {
@@ -6084,6 +6122,11 @@ inline void gcode_M109() {
KEEPALIVE_STATE(NOT_BUSY);
+ #if ENABLED(PRINTER_EVENT_LEDS)
+ const float start_temp = thermalManager.degHotend(target_extruder);
+ uint8_t old_blue = 0;
+ #endif
+
do {
// Target temperature might be changed during the loop
if (target_temp != thermalManager.degTargetHotend(target_extruder)) {
@@ -6117,6 +6160,14 @@ inline void gcode_M109() {
const float temp = thermalManager.degHotend(target_extruder);
+ #if ENABLED(PRINTER_EVENT_LEDS)
+ // Gradually change LED strip from violet to red as nozzle heats up
+ if (!wants_to_cool) {
+ const uint8_t blue = map(constrain(temp, start_temp, target_temp), start_temp, target_temp, 255, 0);
+ if (blue != old_blue) set_led_color(255, 0, (old_blue = blue));
+ }
+ #endif
+
#if TEMP_RESIDENCY_TIME > 0
const float temp_diff = fabs(target_temp - temp);
@@ -6145,7 +6196,12 @@ inline void gcode_M109() {
} while (wait_for_heatup && TEMP_CONDITIONS);
- if (wait_for_heatup) LCD_MESSAGEPGM(MSG_HEATING_COMPLETE);
+ if (wait_for_heatup) {
+ LCD_MESSAGEPGM(MSG_HEATING_COMPLETE);
+ #if ENABLED(PRINTER_EVENT_LEDS)
+ set_led_color(255, 255, 255); // Set LEDs ALL WHITE
+ #endif
+ }
KEEPALIVE_STATE(IN_HANDLER);
}
@@ -6195,6 +6251,11 @@ inline void gcode_M109() {
target_extruder = active_extruder; // for print_heaterstates
+ #if ENABLED(PRINTER_EVENT_LEDS)
+ const float start_temp = thermalManager.degBed();
+ uint8_t old_red = 255;
+ #endif
+
do {
// Target temperature might be changed during the loop
if (target_temp != thermalManager.degTargetBed()) {
@@ -6228,6 +6289,15 @@ inline void gcode_M109() {
const float temp = thermalManager.degBed();
+ #if ENABLED(PRINTER_EVENT_LEDS)
+ // Gradually change LED strip from blue to violet as bed heats up
+ if (!wants_to_cool) {
+ const uint8_t red = map(constrain(temp, start_temp, target_temp), start_temp, target_temp, 0, 255);
+ if (red != old_red) set_led_color((old_red = red), 0, 255);
+ }
+ }
+ #endif
+
#if TEMP_BED_RESIDENCY_TIME > 0
const float temp_diff = fabs(target_temp - temp);
@@ -6771,28 +6841,7 @@ inline void gcode_M121() { endstops.enable_globally(false); }
#endif // PARK_HEAD_ON_PAUSE
-#if ENABLED(BLINKM) || ENABLED(RGB_LED)
-
- void set_led_color(const uint8_t r, const uint8_t g, const uint8_t b) {
-
- #if ENABLED(BLINKM)
-
- // This variant uses i2c to send the RGB components to the device.
- SendColors(r, g, b);
-
- #else
-
- // This variant uses 3 separate pins for the RGB components.
- // If the pins can do PWM then their intensity will be set.
- digitalWrite(RGB_LED_R_PIN, r ? HIGH : LOW);
- digitalWrite(RGB_LED_G_PIN, g ? HIGH : LOW);
- digitalWrite(RGB_LED_B_PIN, b ? HIGH : LOW);
- analogWrite(RGB_LED_R_PIN, r);
- analogWrite(RGB_LED_G_PIN, g);
- analogWrite(RGB_LED_B_PIN, b);
-
- #endif
- }
+#if HAS_COLOR_LEDS
/**
* M150: Set Status LED Color - Use R-U-B for R-G-B
@@ -9388,7 +9437,7 @@ void process_next_command() {
break;
#endif
- #if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #if HAS_COLOR_LEDS
case 150: // M150: Set Status LED Color
gcode_M150();
diff --git a/Marlin/SanityCheck.h b/Marlin/SanityCheck.h
index 0a36616d15500cb7e2d2c1617c1f2bf78f12dd48..3464abe922df0b53659897a3f885404b1b63afba 100644
--- a/Marlin/SanityCheck.h
+++ b/Marlin/SanityCheck.h
@@ -957,6 +957,8 @@ static_assert(1 >= 0
#elif ENABLED(BLINKM)
#error "RGB_LED and BLINKM are currently incompatible (both use M150)."
#endif
+#elif DISABLED(BLINKM) && ENABLED(PRINTER_EVENT_LEDS)
+ #error "PRINTER_EVENT_LEDS requires BLINKM or RGB_LED."
#endif
/**
diff --git a/Marlin/example_configurations/Cartesio/Configuration.h b/Marlin/example_configurations/Cartesio/Configuration.h
index 62d6d8170d3b0fb2157c4bfb33117118d6d10d7d..9d2bc2a339df4f5ccd8bbba98db627881a6b9202 100644
--- a/Marlin/example_configurations/Cartesio/Configuration.h
+++ b/Marlin/example_configurations/Cartesio/Configuration.h
@@ -1513,7 +1513,23 @@
//define BlinkM/CyzRgb Support
//#define BLINKM
-// Support for an RGB LED using 3 separate pins with optional PWM
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
//#define RGB_LED
#if ENABLED(RGB_LED)
#define RGB_LED_R_PIN 34
@@ -1521,6 +1537,21 @@
#define RGB_LED_B_PIN 35
#endif
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #define PRINTER_EVENT_LEDS
+#endif
+
/*********************************************************************\
* R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas
diff --git a/Marlin/example_configurations/Felix/Configuration.h b/Marlin/example_configurations/Felix/Configuration.h
index 71b26a7f1ea01e7189afbb779be6ae4bdce8c5e1..2b670d4e0470f1a71f072076fed313d6a6cf75b0 100644
--- a/Marlin/example_configurations/Felix/Configuration.h
+++ b/Marlin/example_configurations/Felix/Configuration.h
@@ -1497,7 +1497,23 @@
//define BlinkM/CyzRgb Support
//#define BLINKM
-// Support for an RGB LED using 3 separate pins with optional PWM
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
//#define RGB_LED
#if ENABLED(RGB_LED)
#define RGB_LED_R_PIN 34
@@ -1505,6 +1521,21 @@
#define RGB_LED_B_PIN 35
#endif
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #define PRINTER_EVENT_LEDS
+#endif
+
/*********************************************************************\
* R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas
diff --git a/Marlin/example_configurations/Felix/DUAL/Configuration.h b/Marlin/example_configurations/Felix/DUAL/Configuration.h
index 59e5faeab2452557c2fc08ba0fac950dbed3ee26..f5299dea1c09cd357a692609561adaa84fb1d493 100644
--- a/Marlin/example_configurations/Felix/DUAL/Configuration.h
+++ b/Marlin/example_configurations/Felix/DUAL/Configuration.h
@@ -1497,7 +1497,23 @@
//define BlinkM/CyzRgb Support
//#define BLINKM
-// Support for an RGB LED using 3 separate pins with optional PWM
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
//#define RGB_LED
#if ENABLED(RGB_LED)
#define RGB_LED_R_PIN 34
@@ -1505,6 +1521,21 @@
#define RGB_LED_B_PIN 35
#endif
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #define PRINTER_EVENT_LEDS
+#endif
+
/*********************************************************************\
* R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas
diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h
index fef9f3657a22440d456145062d1cc34f7066c5fc..9b5a0493854a37305da24e61d5e523c632a64195 100644
--- a/Marlin/example_configurations/Hephestos/Configuration.h
+++ b/Marlin/example_configurations/Hephestos/Configuration.h
@@ -1505,7 +1505,23 @@
//define BlinkM/CyzRgb Support
//#define BLINKM
-// Support for an RGB LED using 3 separate pins with optional PWM
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
//#define RGB_LED
#if ENABLED(RGB_LED)
#define RGB_LED_R_PIN 34
@@ -1513,6 +1529,21 @@
#define RGB_LED_B_PIN 35
#endif
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #define PRINTER_EVENT_LEDS
+#endif
+
/*********************************************************************\
* R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas
diff --git a/Marlin/example_configurations/Hephestos_2/Configuration.h b/Marlin/example_configurations/Hephestos_2/Configuration.h
index 2d4abfda9a36b0eba13a411348b2e8b28da3d5cc..9af69e578614a6e923e548997866d0ba0979feb4 100644
--- a/Marlin/example_configurations/Hephestos_2/Configuration.h
+++ b/Marlin/example_configurations/Hephestos_2/Configuration.h
@@ -1508,7 +1508,23 @@
//define BlinkM/CyzRgb Support
//#define BLINKM
-// Support for an RGB LED using 3 separate pins with optional PWM
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
//#define RGB_LED
#if ENABLED(RGB_LED)
#define RGB_LED_R_PIN 34
@@ -1516,6 +1532,21 @@
#define RGB_LED_B_PIN 35
#endif
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #define PRINTER_EVENT_LEDS
+#endif
+
/*********************************************************************\
* R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas
diff --git a/Marlin/example_configurations/K8200/Configuration.h b/Marlin/example_configurations/K8200/Configuration.h
index 2bebbd648141f83c6f47f53ce78af0e65828bc6f..747096f6ba15edbbaa05f229e3e6ccf0913404f0 100644
--- a/Marlin/example_configurations/K8200/Configuration.h
+++ b/Marlin/example_configurations/K8200/Configuration.h
@@ -1548,7 +1548,23 @@
//define BlinkM/CyzRgb Support
//#define BLINKM
-// Support for an RGB LED using 3 separate pins with optional PWM
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
//#define RGB_LED
#if ENABLED(RGB_LED)
#define RGB_LED_R_PIN 34
@@ -1556,6 +1572,21 @@
#define RGB_LED_B_PIN 35
#endif
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #define PRINTER_EVENT_LEDS
+#endif
+
/*********************************************************************\
* R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas
diff --git a/Marlin/example_configurations/K8400/Configuration.h b/Marlin/example_configurations/K8400/Configuration.h
index 0b9547453599a7ee07638cb19d250d8c2eba6c02..89e43341264072063bbcc28a61ae91aef524cb7a 100644
--- a/Marlin/example_configurations/K8400/Configuration.h
+++ b/Marlin/example_configurations/K8400/Configuration.h
@@ -1514,7 +1514,23 @@
//define BlinkM/CyzRgb Support
//#define BLINKM
-// Support for an RGB LED using 3 separate pins with optional PWM
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
//#define RGB_LED
#if ENABLED(RGB_LED)
#define RGB_LED_R_PIN 34
@@ -1522,6 +1538,21 @@
#define RGB_LED_B_PIN 35
#endif
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #define PRINTER_EVENT_LEDS
+#endif
+
/*********************************************************************\
* R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas
diff --git a/Marlin/example_configurations/K8400/Dual-head/Configuration.h b/Marlin/example_configurations/K8400/Dual-head/Configuration.h
index 63c3036e6dc5f00ef19df420f6ad34e847ab8406..677ee815d4412129c0aca7e8d02ef35c6922a14a 100644
--- a/Marlin/example_configurations/K8400/Dual-head/Configuration.h
+++ b/Marlin/example_configurations/K8400/Dual-head/Configuration.h
@@ -1514,7 +1514,23 @@
//define BlinkM/CyzRgb Support
//#define BLINKM
-// Support for an RGB LED using 3 separate pins with optional PWM
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
//#define RGB_LED
#if ENABLED(RGB_LED)
#define RGB_LED_R_PIN 34
@@ -1522,6 +1538,21 @@
#define RGB_LED_B_PIN 35
#endif
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #define PRINTER_EVENT_LEDS
+#endif
+
/*********************************************************************\
* R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas
diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
index f5e44da8babf48e313cede1bcdce3aa8d502009b..48c9ed6190f7960797fa5b0febb561b32af793b6 100644
--- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
+++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
@@ -1514,7 +1514,23 @@
//define BlinkM/CyzRgb Support
//#define BLINKM
-// Support for an RGB LED using 3 separate pins with optional PWM
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
//#define RGB_LED
#if ENABLED(RGB_LED)
#define RGB_LED_R_PIN 34
@@ -1522,6 +1538,21 @@
#define RGB_LED_B_PIN 35
#endif
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #define PRINTER_EVENT_LEDS
+#endif
+
/*********************************************************************\
* R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas
diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h
index a7f1bb8f2ec925693ba231c5666d6803d3349bf6..0d35e7a519ab02d4c5ff1b1fa7731865d0e5f4d3 100644
--- a/Marlin/example_configurations/RigidBot/Configuration.h
+++ b/Marlin/example_configurations/RigidBot/Configuration.h
@@ -1515,7 +1515,23 @@
//define BlinkM/CyzRgb Support
//#define BLINKM
-// Support for an RGB LED using 3 separate pins with optional PWM
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
//#define RGB_LED
#if ENABLED(RGB_LED)
#define RGB_LED_R_PIN 34
@@ -1523,6 +1539,21 @@
#define RGB_LED_B_PIN 35
#endif
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #define PRINTER_EVENT_LEDS
+#endif
+
/*********************************************************************\
* R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas
diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h
index 29352b0daec68eb4a2c0ad9bcc4b645515924942..fac1e5109f4a24da0ff33b52369fbfc6c277df90 100644
--- a/Marlin/example_configurations/SCARA/Configuration.h
+++ b/Marlin/example_configurations/SCARA/Configuration.h
@@ -1529,7 +1529,23 @@
//define BlinkM/CyzRgb Support
//#define BLINKM
-// Support for an RGB LED using 3 separate pins with optional PWM
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
//#define RGB_LED
#if ENABLED(RGB_LED)
#define RGB_LED_R_PIN 34
@@ -1537,6 +1553,21 @@
#define RGB_LED_B_PIN 35
#endif
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #define PRINTER_EVENT_LEDS
+#endif
+
/*********************************************************************\
* R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas
diff --git a/Marlin/example_configurations/TAZ4/Configuration.h b/Marlin/example_configurations/TAZ4/Configuration.h
index 03100e59c264ecc78644c1b014b4c36c0ec894bd..9b4d171391e6849807a2dcf4bc619d174e5bee3e 100644
--- a/Marlin/example_configurations/TAZ4/Configuration.h
+++ b/Marlin/example_configurations/TAZ4/Configuration.h
@@ -1534,7 +1534,23 @@
//define BlinkM/CyzRgb Support
//#define BLINKM
-// Support for an RGB LED using 3 separate pins with optional PWM
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
//#define RGB_LED
#if ENABLED(RGB_LED)
#define RGB_LED_R_PIN 34
@@ -1542,6 +1558,21 @@
#define RGB_LED_B_PIN 35
#endif
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #define PRINTER_EVENT_LEDS
+#endif
+
/*********************************************************************\
* R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas
diff --git a/Marlin/example_configurations/TinyBoy2/Configuration.h b/Marlin/example_configurations/TinyBoy2/Configuration.h
index ce24a344edc2eda23c3fb35f5a4a2eaa7e2d2602..4ac036069178ad870abbdb5eaf9eb920da4dd331 100644
--- a/Marlin/example_configurations/TinyBoy2/Configuration.h
+++ b/Marlin/example_configurations/TinyBoy2/Configuration.h
@@ -1570,7 +1570,23 @@
//define BlinkM/CyzRgb Support
//#define BLINKM
-// Support for an RGB LED using 3 separate pins with optional PWM
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
//#define RGB_LED
#if ENABLED(RGB_LED)
#define RGB_LED_R_PIN 34
@@ -1578,6 +1594,21 @@
#define RGB_LED_B_PIN 35
#endif
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #define PRINTER_EVENT_LEDS
+#endif
+
/*********************************************************************\
* R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas
diff --git a/Marlin/example_configurations/WITBOX/Configuration.h b/Marlin/example_configurations/WITBOX/Configuration.h
index 7c69e1b1eb4ff6a0bc2827e6f7e7828ead560b09..46dd900e802a83c5d298bc16092cf44d187c48b9 100644
--- a/Marlin/example_configurations/WITBOX/Configuration.h
+++ b/Marlin/example_configurations/WITBOX/Configuration.h
@@ -1505,7 +1505,23 @@
//define BlinkM/CyzRgb Support
//#define BLINKM
-// Support for an RGB LED using 3 separate pins with optional PWM
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
//#define RGB_LED
#if ENABLED(RGB_LED)
#define RGB_LED_R_PIN 34
@@ -1513,6 +1529,21 @@
#define RGB_LED_B_PIN 35
#endif
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #define PRINTER_EVENT_LEDS
+#endif
+
/*********************************************************************\
* R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas
diff --git a/Marlin/example_configurations/adafruit/ST7565/Configuration.h b/Marlin/example_configurations/adafruit/ST7565/Configuration.h
index 55fde5dc673d852cc09bf50532e7788c447e53a9..565d6eeffc26760eca68487d7a78c2ddc084e212 100644
--- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h
+++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h
@@ -1514,7 +1514,23 @@
//define BlinkM/CyzRgb Support
//#define BLINKM
-// Support for an RGB LED using 3 separate pins with optional PWM
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
//#define RGB_LED
#if ENABLED(RGB_LED)
#define RGB_LED_R_PIN 34
@@ -1522,6 +1538,21 @@
#define RGB_LED_B_PIN 35
#endif
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #define PRINTER_EVENT_LEDS
+#endif
+
/*********************************************************************\
* R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas
diff --git a/Marlin/example_configurations/delta/flsun_kossel_mini/Configuration.h b/Marlin/example_configurations/delta/flsun_kossel_mini/Configuration.h
index 0aeef6f293c33303213d606344950692cba91dd1..add835d340d1164d7b9e1a69a07ac75c852adba3 100644
--- a/Marlin/example_configurations/delta/flsun_kossel_mini/Configuration.h
+++ b/Marlin/example_configurations/delta/flsun_kossel_mini/Configuration.h
@@ -1630,7 +1630,23 @@
//define BlinkM/CyzRgb Support
//#define BLINKM
-// Support for an RGB LED using 3 separate pins with optional PWM
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
//#define RGB_LED
#if ENABLED(RGB_LED)
#define RGB_LED_R_PIN 34
@@ -1638,6 +1654,21 @@
#define RGB_LED_B_PIN 35
#endif
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #define PRINTER_EVENT_LEDS
+#endif
+
/*********************************************************************\
* R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas
diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h
index 6ea0062adab5879db172f1c7a4d08e48663aca12..2ea7d06bdf68fc782dccaa4ebc4cb9d1d48cd4f3 100644
--- a/Marlin/example_configurations/delta/generic/Configuration.h
+++ b/Marlin/example_configurations/delta/generic/Configuration.h
@@ -1616,7 +1616,23 @@
//define BlinkM/CyzRgb Support
//#define BLINKM
-// Support for an RGB LED using 3 separate pins with optional PWM
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
//#define RGB_LED
#if ENABLED(RGB_LED)
#define RGB_LED_R_PIN 34
@@ -1624,6 +1640,21 @@
#define RGB_LED_B_PIN 35
#endif
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #define PRINTER_EVENT_LEDS
+#endif
+
/*********************************************************************\
* R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas
diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
index ebd147e1f14fe9bd95559e6859cafd5fe5bd97a3..ddcba6c0d61aacb8341e64ea8212c42909b93449 100644
--- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
@@ -1612,7 +1612,23 @@
//define BlinkM/CyzRgb Support
//#define BLINKM
-// Support for an RGB LED using 3 separate pins with optional PWM
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
//#define RGB_LED
#if ENABLED(RGB_LED)
#define RGB_LED_R_PIN 34
@@ -1620,6 +1636,21 @@
#define RGB_LED_B_PIN 35
#endif
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #define PRINTER_EVENT_LEDS
+#endif
+
/*********************************************************************\
* R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas
diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
index 39222a3275b0e819369de20b56f0ca418a9516ce..15afad44b0f07fa4343815bd4b2d5000af784118 100644
--- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
@@ -1620,7 +1620,23 @@
//define BlinkM/CyzRgb Support
//#define BLINKM
-// Support for an RGB LED using 3 separate pins with optional PWM
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
//#define RGB_LED
#if ENABLED(RGB_LED)
#define RGB_LED_R_PIN 34
@@ -1628,6 +1644,21 @@
#define RGB_LED_B_PIN 35
#endif
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #define PRINTER_EVENT_LEDS
+#endif
+
/*********************************************************************\
* R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas
diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration.h b/Marlin/example_configurations/delta/kossel_xl/Configuration.h
index f269fe7f4db97a0238f336f128ec785e00be94d6..d39454e442e65361b8f6a93e242bcf3200d8afe2 100644
--- a/Marlin/example_configurations/delta/kossel_xl/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_xl/Configuration.h
@@ -1627,7 +1627,23 @@
//define BlinkM/CyzRgb Support
//#define BLINKM
-// Support for an RGB LED using 3 separate pins with optional PWM
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
//#define RGB_LED
#if ENABLED(RGB_LED)
#define RGB_LED_R_PIN 34
@@ -1635,6 +1651,21 @@
#define RGB_LED_B_PIN 35
#endif
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #define PRINTER_EVENT_LEDS
+#endif
+
/*********************************************************************\
* R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas
diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h
index 39faa4ce46ba0e475d7656a29d66d0652d902d6a..1f642c46f2a54a628652836750ca9330503206d1 100644
--- a/Marlin/example_configurations/makibox/Configuration.h
+++ b/Marlin/example_configurations/makibox/Configuration.h
@@ -1517,7 +1517,23 @@
//define BlinkM/CyzRgb Support
//#define BLINKM
-// Support for an RGB LED using 3 separate pins with optional PWM
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
//#define RGB_LED
#if ENABLED(RGB_LED)
#define RGB_LED_R_PIN 34
@@ -1525,6 +1541,21 @@
#define RGB_LED_B_PIN 35
#endif
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #define PRINTER_EVENT_LEDS
+#endif
+
/*********************************************************************\
* R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas
diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
index 9b90db90b05eafdc075b4f520fa82c34c89878db..e51ddf2c678c79bc033d79c7fb12a7d9f73d225c 100644
--- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h
+++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
@@ -1510,7 +1510,23 @@
//define BlinkM/CyzRgb Support
//#define BLINKM
-// Support for an RGB LED using 3 separate pins with optional PWM
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
//#define RGB_LED
#if ENABLED(RGB_LED)
#define RGB_LED_R_PIN 34
@@ -1518,6 +1534,21 @@
#define RGB_LED_B_PIN 35
#endif
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED)
+ #define PRINTER_EVENT_LEDS
+#endif
+
/*********************************************************************\
* R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas