diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index ee3b619089214e243cbfe75afd0e6f976228823f..24cb61a130f673345c1d6ed14b755fe0e0fbafb2 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -917,7 +917,7 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
- //#define POWER_LOSS_PIN 44 // Pin to detect power loss (optional)
+ //#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
@@ -1159,7 +1159,7 @@
#if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
#define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
// Note: Extra time may be added to mitigate controller latency.
- #define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement).
+ //#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement).
//#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle.
#if ENABLED(MOVE_Z_WHEN_IDLE)
#define MOVE_Z_IDLE_MULTIPLICATOR 1 // Multiply 1mm by this factor for the move step size.
diff --git a/config/examples/Anet/A6/Configuration.h b/config/examples/Anet/A6/Configuration.h
index 1fe45195e738b687473d304673392a71c130595e..35336af8d90853c8d6dadd10c036bd6a4db24163 100644
--- a/config/examples/Anet/A6/Configuration.h
+++ b/config/examples/Anet/A6/Configuration.h
@@ -989,15 +989,14 @@
#if 1 // 0 for less clearance
#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
-#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
//#define Z_AFTER_PROBING 5 // Z position after probing is done
#else
#define Z_CLEARANCE_DEPLOY_PROBE 5 // Z Clearance for Deploy/Stow
#define Z_CLEARANCE_BETWEEN_PROBES 3 // Z Clearance between probe points
-#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
//#define Z_AFTER_PROBING 3 // Z position after probing is done
#endif
+#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
// For M851 give a range for adjusting the Z probe offset
diff --git a/config/examples/BQ/Hephestos_2/Configuration.h b/config/examples/BQ/Hephestos_2/Configuration.h
index 39a44bf1f1111f5a7a72d05f7fa5871d516f3eb8..b7df3c08c2c84cb0cad4227d8f398c6bce9ea776 100644
--- a/config/examples/BQ/Hephestos_2/Configuration.h
+++ b/config/examples/BQ/Hephestos_2/Configuration.h
@@ -1299,7 +1299,7 @@
// Homing speeds (mm/m)
#define HOMING_FEEDRATE_XY (50*60)
-#define HOMING_FEEDRATE_Z ( 4*60)
+#define HOMING_FEEDRATE_Z (4*60)
// Validate that endstops are triggered on homing moves
#define VALIDATE_HOMING_ENDSTOPS
diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h
index e37841ad4be5591cec4e606ca7de54a283df22d4..2b6535ee8c4d8a329dfbcd2c1ef45dc8a2414a44 100644
--- a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h
+++ b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h
@@ -917,7 +917,7 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
- //#define POWER_LOSS_PIN 44 // Pin to detect power loss (optional)
+ //#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
diff --git a/config/examples/Einstart-S/Configuration.h b/config/examples/Einstart-S/Configuration.h
index ea469690222b515bbbc11c8bb2a4bb1eaf2e38e8..cfa8a8a6ab39bb964325936abeef1cbfe3bc2115 100644
--- a/config/examples/Einstart-S/Configuration.h
+++ b/config/examples/Einstart-S/Configuration.h
@@ -379,13 +379,13 @@
* 147 : Pt100 with 4k7 pullup
* 110 : Pt100 with 1k pullup (non standard)
*
+ * 1000 : Custom - Specify parameters in Configuration_adv.h
+ *
* Use these for Testing or Development purposes. NEVER for production machine.
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
*
- * 666 : Custom table generated for 200K thermistor with 10k pullup on Einstart S
- *
- * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" }
+ * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" }
*/
#define TEMP_SENSOR_0 666
#define TEMP_SENSOR_1 0
@@ -820,6 +820,7 @@
* or (with LCD_BED_LEVELING) the LCD controller.
*/
//#define PROBE_MANUALLY
+//#define MANUAL_PROBE_START_Z 0.2
/**
* A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
@@ -928,6 +929,7 @@
*/
#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
+#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
//#define Z_AFTER_PROBING 5 // Z position after probing is done
#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
@@ -1970,6 +1972,15 @@
//
//#define SILVER_GATE_GLCD_CONTROLLER
+//
+// Extensible UI
+//
+// Enable third-party or vendor customized user interfaces that aren't
+// packaged with Marlin. Source code for the user interface will need to
+// be placed in "src/lcd/extensible_ui/lib"
+//
+//#define EXTENSIBLE_UI
+
//
// Einstart S OLED SSD1306
//
diff --git a/config/examples/Formbot/Raptor/Configuration_adv.h b/config/examples/Formbot/Raptor/Configuration_adv.h
index e90e5c74a43a9c6bb444ba44214384ae5d2de790..ae03cf760172d9cedab804b15393b918eff1600a 100644
--- a/config/examples/Formbot/Raptor/Configuration_adv.h
+++ b/config/examples/Formbot/Raptor/Configuration_adv.h
@@ -2255,25 +2255,25 @@
#define CUSTOM_USER_MENUS
#endif
#if ENABLED(CUSTOM_USER_MENUS)
- #define CUSTOM_USER_MENU_TITLE "Commissioning"
- //#define USER_SCRIPT_DONE "M117 User Script Done"
+ #define CUSTOM_USER_MENU_TITLE "Commissioning"
+ //#define USER_SCRIPT_DONE "M117 User Script Done"
#define USER_SCRIPT_AUDIBLE_FEEDBACK
#define USER_SCRIPT_RETURN // Return to status screen after a script
#define USER_DESC_1 "UBL Commission Step 1"
- #define USER_GCODE_1 "M502 \n M500 \n M501 \n M190 S75 \n G28 \n G29 P1 \n G29 S1 \n M117 Run Step 2 \n"
+ #define USER_GCODE_1 "M502\nM500\nM501\nM190 S75\nG28\nG29 P1\nG29 S1\nM117 Run Step 2"
#define USER_DESC_2 "UBL Commission Step 2"
- #define USER_GCODE_2 "G29 S1 \n G29 S0 \n G29 F 10.0 \n G29 A \n M500 \n G28 \n G29 L1 \n M109 S225 \n G1 X150 Y 150 \n G1 Z0 \n M117 Set Z Offset \n"
+ #define USER_GCODE_2 "G29 S1\nG29 S0\nG29 F 10.0\nG29 A\nM500\nG28\nG29 L1\nM109 S225\nG1 X150 Y 150\nG1 Z0\nM117 Set Z Offset"
#define USER_DESC_3 "Prep for Z Adjust"
- #define USER_GCODE_3 "M190 75 \n M104 235 \n G28 \n G29 L1 \n G1 X150 Y 150 \n G1 Z0 \n"
+ #define USER_GCODE_3 "M190 75\nM104 235\nG28\nG29 L1\nG1 X150 Y 150\nG1 Z0"
- #define USER_DESC_4 "Fill Mesh Points"
- #define USER_GCODE_4 "G29 P3 \n G29 P3 \n G29 P3 \n G29 T \n"
+ #define USER_DESC_4 "Fill Mesh Points"
+ #define USER_GCODE_4 "G29 P3\nG29 P3\nG29 P3\nG29 T"
- #define USER_DESC_5 "Run Mesh Validation"
- #define USER_GCODE_5 "G26 \n"
+ #define USER_DESC_5 "Run Mesh Validation"
+ #define USER_GCODE_5 "G26"
#endif
/**
diff --git a/config/examples/Geeetech/A10/Configuration_adv.h b/config/examples/Geeetech/A10/Configuration_adv.h
index 8ec7846854cc1cad75f8e5ea9e442a8aba152b0d..fec17c7972e38ea63c80a2018854c7837b5954d0 100644
--- a/config/examples/Geeetech/A10/Configuration_adv.h
+++ b/config/examples/Geeetech/A10/Configuration_adv.h
@@ -917,7 +917,7 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
- //#define POWER_LOSS_PIN 44 // Pin to detect power loss (optional)
+ //#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
diff --git a/config/examples/Geeetech/A20M/Configuration.h b/config/examples/Geeetech/A20M/Configuration.h
index 7cc7c4ec9b95d433c2db65186956ac3418e5ab03..cd4c809d7fd3dd796f6c903f2be0859926994696 100644
--- a/config/examples/Geeetech/A20M/Configuration.h
+++ b/config/examples/Geeetech/A20M/Configuration.h
@@ -1694,7 +1694,6 @@
// ULTIPANEL as seen on Thingiverse.
//
#define ULTIPANEL
-#define NEWPANEL
//
// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
diff --git a/config/examples/Geeetech/MeCreator2/Configuration_adv.h b/config/examples/Geeetech/MeCreator2/Configuration_adv.h
index eaaa4d40c2e9e7862446ca632af8a52ab93f8d73..678fea6af0f50b4bb7da9859539aeec16f5083a4 100644
--- a/config/examples/Geeetech/MeCreator2/Configuration_adv.h
+++ b/config/examples/Geeetech/MeCreator2/Configuration_adv.h
@@ -2218,6 +2218,21 @@
*/
#define FASTER_GCODE_PARSER
+/**
+ * CNC G-code options
+ * Support CNC-style G-code dialects used by laser cutters, drawing machine cams, etc.
+ * Note that G0 feedrates should be used with care for 3D printing (if used at all).
+ * High feedrates may cause ringing and harm print quality.
+ */
+//#define PAREN_COMMENTS // Support for parentheses-delimited comments
+//#define GCODE_MOTION_MODES // Remember the motion mode (G0 G1 G2 G3 G5 G38.X) and apply for X Y Z E F, etc.
+
+// Enable and set a (default) feedrate for all G0 moves
+//#define G0_FEEDRATE 3000 // (mm/m)
+#ifdef G0_FEEDRATE
+ //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
+#endif
+
/**
* G-code Macros
*
diff --git a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h
index f35724fc23149b4c3f51a5cb51daace0cd4a4b00..ed0b780bb207b7d20d0c85f1f6a69019bd61d0e6 100644
--- a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h
+++ b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h
@@ -321,6 +321,7 @@
#define AUTO_POWER_FANS // Turn on PSU if fans need power
#define AUTO_POWER_E_FANS
#define AUTO_POWER_CONTROLLERFAN
+ #define AUTO_POWER_CHAMBER_FAN
#define POWER_TIMEOUT 30
#endif
diff --git a/config/examples/JGAurora/A1/Configuration.h b/config/examples/JGAurora/A1/Configuration.h
index a7d0b2ad45475e5360978ff2ac4706dc83638a94..4d4a40f8ae2d4277db0e3b4abdeea5f98a95a8ee 100644
--- a/config/examples/JGAurora/A1/Configuration.h
+++ b/config/examples/JGAurora/A1/Configuration.h
@@ -1982,7 +1982,6 @@
// MKS Robin 320x240 color display
// Also used for JGAurora A5S & A1 TFT LCD's (16-bit Parallel LCD via FSMC)
#define MKS_ROBIN_TFT
-#define PRINTER_EVENT_LEDS
//=============================================================================
//============================ Other Controllers ============================
diff --git a/config/examples/JGAurora/A1/Configuration_adv.h b/config/examples/JGAurora/A1/Configuration_adv.h
index 8aa13049369a7fc010169a7d8de84d8b29755ad2..3b1873187a947ee16712d773e8c6f83c68b792d5 100644
--- a/config/examples/JGAurora/A1/Configuration_adv.h
+++ b/config/examples/JGAurora/A1/Configuration_adv.h
@@ -922,7 +922,7 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
- //#define POWER_LOSS_PIN 44 // Pin to detect power loss (optional)
+ //#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
diff --git a/config/examples/JGAurora/A5S/Configuration_adv.h b/config/examples/JGAurora/A5S/Configuration_adv.h
index 8aa13049369a7fc010169a7d8de84d8b29755ad2..3b1873187a947ee16712d773e8c6f83c68b792d5 100644
--- a/config/examples/JGAurora/A5S/Configuration_adv.h
+++ b/config/examples/JGAurora/A5S/Configuration_adv.h
@@ -922,7 +922,7 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
- //#define POWER_LOSS_PIN 44 // Pin to detect power loss (optional)
+ //#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
index 5a95ba22064c84e3d5814b169bd7f556f0fe0e0c..ae1cb02185265cdafec04c23857ff27cabb44669 100644
--- a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
+++ b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
@@ -1166,6 +1166,8 @@
#endif
#endif
+ //#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28
+
//#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping
#if ENABLED(BABYSTEP_ZPROBE_OFFSET)
//#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
diff --git a/config/examples/Tronxy/X5S/Configuration.h b/config/examples/Tronxy/X5S/Configuration.h
index 8990e24cd19b82802dcd94242f6cf8100167a26d..b23399d8ff3c9a93b9b1515c1d590ff7d715447b 100644
--- a/config/examples/Tronxy/X5S/Configuration.h
+++ b/config/examples/Tronxy/X5S/Configuration.h
@@ -445,7 +445,8 @@
#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
#define PID_K1 0.95 // Smoothing factor within any PID loop
#if ENABLED(PIDTEMP)
- #define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
+ //#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+ #define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
//#define PID_DEBUG // Sends debug data to the serial port.
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
diff --git a/config/examples/delta/Anycubic/Kossel/Configuration.h b/config/examples/delta/Anycubic/Kossel/Configuration.h
index 383b4a31540b4e1c4e30df62024a20adf7d6fcc0..e44f2aa7049c62d3e33e8724cec73872367f3e1a 100644
--- a/config/examples/delta/Anycubic/Kossel/Configuration.h
+++ b/config/examples/delta/Anycubic/Kossel/Configuration.h
@@ -1311,6 +1311,7 @@
//#define AUTO_BED_LEVELING_UBL
//#define MESH_BED_LEVELING
#endif
+
/**
* Normally G28 leaves leveling disabled on completion. Enable
* this option to have G28 restore the prior leveling state.
diff --git a/config/examples/delta/Tevo Little Monster/Configuration_adv.h b/config/examples/delta/Tevo Little Monster/Configuration_adv.h
index 1fd43d6e5cb2c51af57d4cc9e2e06f3543069661..72a3aee019e66da97177cbfaef40d7d44b26ac3f 100644
--- a/config/examples/delta/Tevo Little Monster/Configuration_adv.h
+++ b/config/examples/delta/Tevo Little Monster/Configuration_adv.h
@@ -2236,6 +2236,18 @@
//#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
#endif
+/**
+ * G-code Macros
+ *
+ * Add G-codes M810-M819 to define and run G-code macros.
+ * Macros are not saved to EEPROM.
+ */
+//#define GCODE_MACROS
+#if ENABLED(GCODE_MACROS)
+ #define GCODE_MACROS_SLOTS 5 // Up to 10 may be used
+ #define GCODE_MACROS_SLOT_SIZE 50 // Maximum length of a single macro
+#endif
+
/**
* User-defined menu items that execute custom GCode
*/
diff --git a/config/examples/delta/kossel_mini/Configuration_adv.h b/config/examples/delta/kossel_mini/Configuration_adv.h
index 3695eed54f9314500e4bc12bbdc0f77af0a10839..58c6260c48c28cf4f8a94370fc982203967c99b2 100644
--- a/config/examples/delta/kossel_mini/Configuration_adv.h
+++ b/config/examples/delta/kossel_mini/Configuration_adv.h
@@ -754,6 +754,7 @@
#define CALIBRATION_PIN_PULLUP
#endif
#endif
+
/**
* Adaptive Step Smoothing increases the resolution of multi-axis moves, particularly at step frequencies
* below 1kHz (for AVR) or 10kHz (for ARM), where aliasing between axes in multi-axis moves causes audible