diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index 3e9322295d172e2e7491246d30edff5cb05353b4..fb1cdd016f8a4fe337ff4ca940fe21dd839afe05 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/default/Configuration_adv.h b/config/default/Configuration_adv.h index e65fa5b4bedb3ab8d8eb65ac635da517c0d26bdf..6a7d0539fd4dd7bcd11cbd7ece7dfdb768588eb2 100644 --- a/config/default/Configuration_adv.h +++ b/config/default/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h index 2c9d12c542b34753a22d47fe2e6f4ee15a77148b..755b1c11f9f6854c8a471c3109a13c949278afd1 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/config/examples/AlephObjects/TAZ4/Configuration_adv.h index 46257df917ffe74609c946b90846459509c53142..c6c7285d7580ddc840d71412a85c34938c8b8622 100644 --- a/config/examples/AlephObjects/TAZ4/Configuration_adv.h +++ b/config/examples/AlephObjects/TAZ4/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/AliExpress/UM2pExt/Configuration_adv.h b/config/examples/AliExpress/UM2pExt/Configuration_adv.h index 90f3d5dc321dbf723d21b471f4116d2cfb932b0b..600a86cdbf73bb8cb63c69f72f5ff3bdf8c9527b 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration_adv.h +++ b/config/examples/AliExpress/UM2pExt/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Anet/A2/Configuration_adv.h b/config/examples/Anet/A2/Configuration_adv.h index a1e768993332f7af17694b418c9c541e5a80ec02..b8038ed8fd14cfeede05bb65975f1b8c70f546a0 100644 --- a/config/examples/Anet/A2/Configuration_adv.h +++ b/config/examples/Anet/A2/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Anet/A2plus/Configuration_adv.h b/config/examples/Anet/A2plus/Configuration_adv.h index a1e768993332f7af17694b418c9c541e5a80ec02..b8038ed8fd14cfeede05bb65975f1b8c70f546a0 100644 --- a/config/examples/Anet/A2plus/Configuration_adv.h +++ b/config/examples/Anet/A2plus/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Anet/A6/Configuration_adv.h b/config/examples/Anet/A6/Configuration_adv.h index 316be512fd80112337550f9c9aeb9df1bb8f1667..aea3e5902d977c168fdc64946dc2682d14e721c4 100644 --- a/config/examples/Anet/A6/Configuration_adv.h +++ b/config/examples/Anet/A6/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Anet/A8/Configuration_adv.h b/config/examples/Anet/A8/Configuration_adv.h index b86d99b925d098295500014e041da3e816b6bcdb..95c5b461584a76ac24e35e58f11190f25c02cfce 100644 --- a/config/examples/Anet/A8/Configuration_adv.h +++ b/config/examples/Anet/A8/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/AnyCubic/i3/Configuration_adv.h b/config/examples/AnyCubic/i3/Configuration_adv.h index 84e0ae0406bab827cd2ba1d0fafd94e14afef636..744b4342b8500f7142ac588fa58c0869530ce413 100644 --- a/config/examples/AnyCubic/i3/Configuration_adv.h +++ b/config/examples/AnyCubic/i3/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/ArmEd/Configuration_adv.h b/config/examples/ArmEd/Configuration_adv.h index d38495c079b7041f57d658d509956f186bc2b134..f884b513e9b69f063d40b4f924800f58645594e8 100644 --- a/config/examples/ArmEd/Configuration_adv.h +++ b/config/examples/ArmEd/Configuration_adv.h @@ -408,20 +408,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h index 211aa4d5f29350b9bea4e32232a2b79e6cbd0aa4..baa7629e2a83b9cd50fd01b497c6fd184d2f5052 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/BIBO/TouchX/default/Configuration_adv.h b/config/examples/BIBO/TouchX/default/Configuration_adv.h index 3c8060da38ad9862c2fd074a2632b75c2261279e..6636407c26dce1e71bda7a0decd355636c1d3536 100644 --- a/config/examples/BIBO/TouchX/default/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/default/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/BQ/Hephestos/Configuration_adv.h b/config/examples/BQ/Hephestos/Configuration_adv.h index d237706bf26d93e8bd515e6ac9f8dd9e98406507..c436b1019935c6e0434f3fe69c0a6240a37a108b 100644 --- a/config/examples/BQ/Hephestos/Configuration_adv.h +++ b/config/examples/BQ/Hephestos/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/BQ/Hephestos_2/Configuration_adv.h b/config/examples/BQ/Hephestos_2/Configuration_adv.h index a07ba4f1e0480bad723eb7c0d03be35192e80f5f..a8549fb4a3768b88b93e1d9ccb61330b9f6331ef 100644 --- a/config/examples/BQ/Hephestos_2/Configuration_adv.h +++ b/config/examples/BQ/Hephestos_2/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/BQ/WITBOX/Configuration_adv.h b/config/examples/BQ/WITBOX/Configuration_adv.h index d237706bf26d93e8bd515e6ac9f8dd9e98406507..c436b1019935c6e0434f3fe69c0a6240a37a108b 100644 --- a/config/examples/BQ/WITBOX/Configuration_adv.h +++ b/config/examples/BQ/WITBOX/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Cartesio/Configuration_adv.h b/config/examples/Cartesio/Configuration_adv.h index a4fd1740e11562975fd4c94b02861fca44fcad89..15e8fad4d2b0ff61e1d834c5b5603faa15566f48 100644 --- a/config/examples/Cartesio/Configuration_adv.h +++ b/config/examples/Cartesio/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Creality/CR-10/Configuration_adv.h b/config/examples/Creality/CR-10/Configuration_adv.h index a91c450245ec5b5cd1d6ad93169c64fbf523f78d..2381632e6fe765a7599ba57ca39c0a93f43076f6 100644 --- a/config/examples/Creality/CR-10/Configuration_adv.h +++ b/config/examples/Creality/CR-10/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Creality/CR-10S/Configuration_adv.h b/config/examples/Creality/CR-10S/Configuration_adv.h index cd0c8e207747881cda30c1004185581bd532290c..607429c4fb76c3e288188d748a8a3f7f1f78c0f5 100644 --- a/config/examples/Creality/CR-10S/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Creality/CR-10_5S/Configuration_adv.h b/config/examples/Creality/CR-10_5S/Configuration_adv.h index 8fe01bc7c64d368cb7b334764536c7a824ece265..085bd2df0a1fd6beea5341d10dbf5d0d48427859 100644 --- a/config/examples/Creality/CR-10_5S/Configuration_adv.h +++ b/config/examples/Creality/CR-10_5S/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Creality/CR-10mini/Configuration_adv.h b/config/examples/Creality/CR-10mini/Configuration_adv.h index d477607c5d456fc24e14c4dd24fe47fc7abaca08..6fe46f18884c4784a008736fa142959ab5c2673b 100644 --- a/config/examples/Creality/CR-10mini/Configuration_adv.h +++ b/config/examples/Creality/CR-10mini/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Creality/CR-8/Configuration_adv.h b/config/examples/Creality/CR-8/Configuration_adv.h index 439619f49f2de718666149244bceaf9d604fefc9..15187211dad3ab944b4218198045d38bc946ff6d 100644 --- a/config/examples/Creality/CR-8/Configuration_adv.h +++ b/config/examples/Creality/CR-8/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Creality/Ender-2/Configuration_adv.h b/config/examples/Creality/Ender-2/Configuration_adv.h index 1f94606abb008437acae22d3075bb1f2dc22669c..4351c0fbcbd22092bf93ef3ef9b1e21f815e54a8 100644 --- a/config/examples/Creality/Ender-2/Configuration_adv.h +++ b/config/examples/Creality/Ender-2/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Creality/Ender-3/Configuration_adv.h b/config/examples/Creality/Ender-3/Configuration_adv.h index f276867d676242f0896517ac51cf68caa3449dee..b716135211560ef98a796e610a148d20dd32015b 100644 --- a/config/examples/Creality/Ender-3/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Creality/Ender-4/Configuration_adv.h b/config/examples/Creality/Ender-4/Configuration_adv.h index 4cc43b92291ca593bb1e52534a1d503da917b967..34eaa61d4034b1efcca1ab309e974140ee3a6701 100644 --- a/config/examples/Creality/Ender-4/Configuration_adv.h +++ b/config/examples/Creality/Ender-4/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Einstart-S/Configuration_adv.h b/config/examples/Einstart-S/Configuration_adv.h index c1655e6bf6444551fd9e00baf30fa8bd294d1bce..268034a91508655d025927a6faa435212b4e37b5 100644 --- a/config/examples/Einstart-S/Configuration_adv.h +++ b/config/examples/Einstart-S/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Felix/Configuration_adv.h b/config/examples/Felix/Configuration_adv.h index 5291a33404397db3a6d9c1bb0200f8389de1a25c..89522e4701fcd435c67e74d945ab9f65c716b7e1 100644 --- a/config/examples/Felix/Configuration_adv.h +++ b/config/examples/Felix/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/FlashForge/CreatorPro/Configuration_adv.h b/config/examples/FlashForge/CreatorPro/Configuration_adv.h index c07a5f72342a759609c794c054600402b9468b9d..6c73c50fb56ea54655b0625cb6d58cc2e1c79152 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration_adv.h +++ b/config/examples/FlashForge/CreatorPro/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/config/examples/FolgerTech/i3-2020/Configuration_adv.h index f33a78c0019e3c4d23c7c5d6248ce14c7dec8016..cbde4c0dbca0d47b6eeec8e238ddaaf9475e6029 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration_adv.h +++ b/config/examples/FolgerTech/i3-2020/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Formbot/Raptor/Configuration_adv.h b/config/examples/Formbot/Raptor/Configuration_adv.h index 1e6a88cd8449fc1dfdb5d7abf9f9297ff149001f..7bfe83f4c0e5a6a6d5147e57a71fb340775f4ba3 100644 --- a/config/examples/Formbot/Raptor/Configuration_adv.h +++ b/config/examples/Formbot/Raptor/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h index ed4a364dd8f8a5c255572055e2b4c334d3d1c7e5..20dbb1c2810e935a716cf16384f6a7fa70b9715c 100644 --- a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h +++ b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h @@ -408,20 +408,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Formbot/T_Rex_3/Configuration_adv.h b/config/examples/Formbot/T_Rex_3/Configuration_adv.h index b3dd5310c20bb241397439a1e85648f69c83c398..8d5a30d3ba21176ec30d6ca48840e54764954e8a 100644 --- a/config/examples/Formbot/T_Rex_3/Configuration_adv.h +++ b/config/examples/Formbot/T_Rex_3/Configuration_adv.h @@ -408,20 +408,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Geeetech/A10M/Configuration_adv.h b/config/examples/Geeetech/A10M/Configuration_adv.h index 2554edfcaa63f02bf8b6a4e1917936c1c5c6fb49..154f8112cb87d1b42e55f9599af3e94e5c43f870 100644 --- a/config/examples/Geeetech/A10M/Configuration_adv.h +++ b/config/examples/Geeetech/A10M/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Geeetech/A20M/Configuration_adv.h b/config/examples/Geeetech/A20M/Configuration_adv.h index a01c1e172228a0e05e79b77814ea48b33122ec43..da1c3eb393903a599bb7dca03e4bb40e950ae03e 100644 --- a/config/examples/Geeetech/A20M/Configuration_adv.h +++ b/config/examples/Geeetech/A20M/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Geeetech/MeCreator2/Configuration_adv.h b/config/examples/Geeetech/MeCreator2/Configuration_adv.h index b97e256d1ec359eb19dac1ce6b43d6ed94b6908c..8326f1b245a667c2da41c0aa1529e264bf5c0e83 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration_adv.h +++ b/config/examples/Geeetech/MeCreator2/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h index 9cf7beef859e53ec5eab90a26bb2ce5ea63582c8..9eb0b35f0c0a44cd5f3fd4fdc80381eb8e9b326c 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h index 9cf7beef859e53ec5eab90a26bb2ce5ea63582c8..9eb0b35f0c0a44cd5f3fd4fdc80381eb8e9b326c 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Infitary/i3-M508/Configuration_adv.h b/config/examples/Infitary/i3-M508/Configuration_adv.h index af5a64497d1c4971058fbd332f90cc4d738597fb..a91b9a143cbad364c8bf25e6680eea79f6536ecd 100644 --- a/config/examples/Infitary/i3-M508/Configuration_adv.h +++ b/config/examples/Infitary/i3-M508/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/JGAurora/A5/Configuration_adv.h b/config/examples/JGAurora/A5/Configuration_adv.h index 5c9653e57c4f98ccebb1912a27c1a36289dd05b3..4868557501b9e08881e39a0f70a19bcb2e5ee486 100644 --- a/config/examples/JGAurora/A5/Configuration_adv.h +++ b/config/examples/JGAurora/A5/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/MakerParts/Configuration_adv.h b/config/examples/MakerParts/Configuration_adv.h index 2fb58aae00f1e640b441343533c4e34f260917e0..ac0bba2040bc09f03cb3d14983f7967283b1b9c2 100644 --- a/config/examples/MakerParts/Configuration_adv.h +++ b/config/examples/MakerParts/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Malyan/M150/Configuration_adv.h b/config/examples/Malyan/M150/Configuration_adv.h index b8aef1a13d90c3f90760ca2a56f9e480c64b43df..a78fe30f7a44c9bbbb3a245216bfe1da28dcf8f7 100644 --- a/config/examples/Malyan/M150/Configuration_adv.h +++ b/config/examples/Malyan/M150/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Malyan/M200/Configuration_adv.h b/config/examples/Malyan/M200/Configuration_adv.h index 7a05d713e30331f1fac117b935b53459c20aca9f..0437a737e35bb993f4f385daf455a4dc8197bb73 100644 --- a/config/examples/Malyan/M200/Configuration_adv.h +++ b/config/examples/Malyan/M200/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/config/examples/Micromake/C1/enhanced/Configuration_adv.h index e65fa5b4bedb3ab8d8eb65ac635da517c0d26bdf..6a7d0539fd4dd7bcd11cbd7ece7dfdb768588eb2 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration_adv.h +++ b/config/examples/Micromake/C1/enhanced/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Mks/Robin/Configuration_adv.h b/config/examples/Mks/Robin/Configuration_adv.h index 12b1f781bed041a1024f9e111147fcaa4b501d2d..8b696aa9321ce101a602ea659580f66caf91e1ca 100644 --- a/config/examples/Mks/Robin/Configuration_adv.h +++ b/config/examples/Mks/Robin/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Mks/Sbase/Configuration_adv.h b/config/examples/Mks/Sbase/Configuration_adv.h index 7291c84cc40cd5602496b21bbbaa21d8bb10348d..7446ec062ed1831884260ea9acc5d4e63e1ef034 100644 --- a/config/examples/Mks/Sbase/Configuration_adv.h +++ b/config/examples/Mks/Sbase/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/RapideLite/RL200/Configuration_adv.h b/config/examples/RapideLite/RL200/Configuration_adv.h index 2b45be65b8d0e4febaa19934fb73f052aa35f46b..49c99e7a7474d0906af6a1ecabdb84206d5d3e3e 100644 --- a/config/examples/RapideLite/RL200/Configuration_adv.h +++ b/config/examples/RapideLite/RL200/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/RigidBot/Configuration_adv.h b/config/examples/RigidBot/Configuration_adv.h index e2677991be0ed82c5dc6b90138bf6cf7584b90f5..015603151bb333af26d8f9a389121815802b3de1 100644 --- a/config/examples/RigidBot/Configuration_adv.h +++ b/config/examples/RigidBot/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/SCARA/Configuration_adv.h b/config/examples/SCARA/Configuration_adv.h index d93dfc5279971af828cb5c2abde7615e4b91a081..a7737510e0af73897316b012e525b2bf6ee2fdbe 100644 --- a/config/examples/SCARA/Configuration_adv.h +++ b/config/examples/SCARA/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Sanguinololu/Configuration_adv.h b/config/examples/Sanguinololu/Configuration_adv.h index 4d65dc96e1853b1f76a4978c51263549d613f568..dbd5b6067c8cfc60824f62c8a0a9b450b0200cad 100644 --- a/config/examples/Sanguinololu/Configuration_adv.h +++ b/config/examples/Sanguinololu/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/TheBorg/Configuration_adv.h b/config/examples/TheBorg/Configuration_adv.h index 67fdbce9805185d9e6ccd1b9638420d8e01860d0..91bbb2e09fe44e36718ee8b0a9676aac16cd6faf 100644 --- a/config/examples/TheBorg/Configuration_adv.h +++ b/config/examples/TheBorg/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/TinyBoy2/Configuration_adv.h b/config/examples/TinyBoy2/Configuration_adv.h index 55ece61937cadd77b99d82360ae9c70ae9fdacb4..62d3004bd0e49d5c631406bda0f5cbf19613f91d 100644 --- a/config/examples/TinyBoy2/Configuration_adv.h +++ b/config/examples/TinyBoy2/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Tronxy/X3A/Configuration_adv.h b/config/examples/Tronxy/X3A/Configuration_adv.h index 98aee83b516e710ff02ed11efc57c459f159cd93..8b3f1110383fe7e2d96a0ecda38b1a9c8182a5de 100644 --- a/config/examples/Tronxy/X3A/Configuration_adv.h +++ b/config/examples/Tronxy/X3A/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Tronxy/X5S-2E/Configuration_adv.h b/config/examples/Tronxy/X5S-2E/Configuration_adv.h index e629e95a4e8037b67836d4e8ead8cb6f4165e4d5..55c1944c7bb055b7935758ab82d2e65df1b2728f 100644 --- a/config/examples/Tronxy/X5S-2E/Configuration_adv.h +++ b/config/examples/Tronxy/X5S-2E/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/UltiMachine/Archim1/Configuration_adv.h b/config/examples/UltiMachine/Archim1/Configuration_adv.h index 39318e03ed3391d0ebf545ee88d0c17ddfcff259..2ac05f109e32bd80507a16fd8059eba8c574d098 100644 --- a/config/examples/UltiMachine/Archim1/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim1/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/UltiMachine/Archim2/Configuration_adv.h b/config/examples/UltiMachine/Archim2/Configuration_adv.h index 16661e6b51e82f16a5a9de7b3c90e65c1d001a31..ee27d50832f2b028d7ce5792adeffca9d80e56cd 100644 --- a/config/examples/UltiMachine/Archim2/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim2/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/VORONDesign/Configuration_adv.h b/config/examples/VORONDesign/Configuration_adv.h index 9077cf2cb82bd534e5e54e19411f6280e7ea48fe..acb0c9ec82cf976f328e3d356f16bc2711b78620 100644 --- a/config/examples/VORONDesign/Configuration_adv.h +++ b/config/examples/VORONDesign/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Velleman/K8200/Configuration_adv.h b/config/examples/Velleman/K8200/Configuration_adv.h index ad4df85aef4b764b6958cc0425dc460b7d706f2e..fdd3360ba09328f30c3672615d0de379e20f2cd9 100644 --- a/config/examples/Velleman/K8200/Configuration_adv.h +++ b/config/examples/Velleman/K8200/Configuration_adv.h @@ -417,20 +417,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Velleman/K8400/Configuration_adv.h b/config/examples/Velleman/K8400/Configuration_adv.h index 0d3671c28cba90c9d5bf6695498f91b7985efc93..3ef3c734ef411ed23ce85f593c4b4bda2886dfe4 100644 --- a/config/examples/Velleman/K8400/Configuration_adv.h +++ b/config/examples/Velleman/K8400/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/WASP/PowerWASP/Configuration_adv.h b/config/examples/WASP/PowerWASP/Configuration_adv.h index 634c2fd3ea2bae31d12977b68e2bb9fc778a0a7e..a9bacc315249354de30515b7985549dece806157 100644 --- a/config/examples/WASP/PowerWASP/Configuration_adv.h +++ b/config/examples/WASP/PowerWASP/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h index 3f8a851c00aca6d91e8456d65c39f35e4af019d4..bbe3386ac35affdcc54fb28a5611093672d07b27 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h index 017b18f6671241818955ffd1fee1a5af0af5c83e..e187a00eb6f63cb446bb942b8150c7db6969a35d 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h index de784bbf4c22252d3071e0167de70d60e05651a1..ada2271177f8cb0bb0196b33004722f9f3758cf3 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/config/examples/delta/FLSUN/kossel/Configuration_adv.h index de784bbf4c22252d3071e0167de70d60e05651a1..ada2271177f8cb0bb0196b33004722f9f3758cf3 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h index 29485a1dcacd587fbd62dcd08160a41bac7b3eab..39749f07bae25efb66030311fbc0e5d1cc5126d5 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h index 29485a1dcacd587fbd62dcd08160a41bac7b3eab..39749f07bae25efb66030311fbc0e5d1cc5126d5 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/delta/MKS/SBASE/Configuration_adv.h b/config/examples/delta/MKS/SBASE/Configuration_adv.h index e004a95ab69147da372a44e92feae4c548900e4a..f6ef2ce04b78ed456a58821752e6de5f96cd905e 100644 --- a/config/examples/delta/MKS/SBASE/Configuration_adv.h +++ b/config/examples/delta/MKS/SBASE/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/delta/Tevo Little Monster/Configuration_adv.h b/config/examples/delta/Tevo Little Monster/Configuration_adv.h index 3e3a7593076562332ca1c5029ee68c9fe95103ad..094e944b495b983c086b0441486a15ba338774c7 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration_adv.h +++ b/config/examples/delta/Tevo Little Monster/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/delta/generic/Configuration_adv.h b/config/examples/delta/generic/Configuration_adv.h index 29485a1dcacd587fbd62dcd08160a41bac7b3eab..39749f07bae25efb66030311fbc0e5d1cc5126d5 100644 --- a/config/examples/delta/generic/Configuration_adv.h +++ b/config/examples/delta/generic/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/delta/kossel_mini/Configuration_adv.h b/config/examples/delta/kossel_mini/Configuration_adv.h index 3ac997f63b0361c5061b69b832c404313cc0bdf9..60e6f7b6194f24efbb811ecbc6ab9997802f2a2a 100644 --- a/config/examples/delta/kossel_mini/Configuration_adv.h +++ b/config/examples/delta/kossel_mini/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/delta/kossel_xl/Configuration_adv.h b/config/examples/delta/kossel_xl/Configuration_adv.h index 528f003671edbe3996366f7c4f4c11fca067237a..32b0e372eff57ff1d3dcc2b2ad00fbe025fec831 100644 --- a/config/examples/delta/kossel_xl/Configuration_adv.h +++ b/config/examples/delta/kossel_xl/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/config/examples/gCreate/gMax1.5+/Configuration_adv.h index c1b4373f2efa51b610ed1315b712138d7f246d21..b2e8e5e859b273cd79b9e65761a40e6e25b67301 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration_adv.h +++ b/config/examples/gCreate/gMax1.5+/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/makibox/Configuration_adv.h b/config/examples/makibox/Configuration_adv.h index 438e759454e5672b35927c59dc23ab50f6964ec0..71677eeef94f7b63edda891d7af07cbf2c2687c0 100644 --- a/config/examples/makibox/Configuration_adv.h +++ b/config/examples/makibox/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/tvrrug/Round2/Configuration_adv.h b/config/examples/tvrrug/Round2/Configuration_adv.h index 8d91fdcdbe9ddf53c3770bf32b4f752948233af3..5566746b6ba7a3b16c7eb193f5139a889cf0f918 100644 --- a/config/examples/tvrrug/Round2/Configuration_adv.h +++ b/config/examples/tvrrug/Round2/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and diff --git a/config/examples/wt150/Configuration_adv.h b/config/examples/wt150/Configuration_adv.h index e1a4da393df10ec6f6f886deeea11f023d5c2681..0b1ab4e2499802748bab727d0ff17e643331e480 100644 --- a/config/examples/wt150/Configuration_adv.h +++ b/config/examples/wt150/Configuration_adv.h @@ -404,20 +404,20 @@ * The inactive carriage is parked automatically to prevent oozing. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. * By default the X2 stepper is assigned to the first unused E plug on the board. - * + * * The following Dual X Carriage modes can be selected with M605 S<mode>: - * + * * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel * results as long as it supports dual X-carriages. (M605 S0) - * + * * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so * that additional slicer support is not required. (M605 S1) - * + * * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with * the first X-carriage and extruder, to print 2 copies of the same object at the same time. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and * follow with M605 S2 to initiate duplicated movement. - * + * * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates * the movement of the first except the second extruder is reversed in the X axis. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and