From caeba33d28b420acb868599914abab3d2fd7cd49 Mon Sep 17 00:00:00 2001
From: Scott Lahteine <github@thinkyhead.com>
Date: Tue, 16 Jun 2020 14:08:51 -0500
Subject: [PATCH] Sensor 502 and PTC cleanup
---
Marlin/Configuration.h | 1 +
Marlin/Configuration_adv.h | 20 ++++++++++----------
2 files changed, 11 insertions(+), 10 deletions(-)
diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 6352f9e6ef..9109e723d0 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -373,6 +373,7 @@
* 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
* 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
* 501 : 100K Zonestar (Tronxy X3A) Thermistor
+ * 502 : 100K Zonestar Thermistor used by hot bed in Zonestar Prusa P802M
* 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
* 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
* 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 7c9c8b0668..b63253a27c 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -1666,33 +1666,33 @@
// Probe temperature calibration generates a table of values starting at PTC_SAMPLE_START
// (e.g. 30), in steps of PTC_SAMPLE_RES (e.g. 5) with PTC_SAMPLE_COUNT (e.g. 10) samples.
- // #define PTC_SAMPLE_START 30.0f
- // #define PTC_SAMPLE_RES 5.0f
- // #define PTC_SAMPLE_COUNT 10U
+ //#define PTC_SAMPLE_START 30.0f
+ //#define PTC_SAMPLE_RES 5.0f
+ //#define PTC_SAMPLE_COUNT 10U
// Bed temperature calibration builds a similar table.
- // #define BTC_SAMPLE_START 60.0f
- // #define BTC_SAMPLE_RES 5.0f
- // #define BTC_SAMPLE_COUNT 10U
+ //#define BTC_SAMPLE_START 60.0f
+ //#define BTC_SAMPLE_RES 5.0f
+ //#define BTC_SAMPLE_COUNT 10U
// The temperature the probe should be at while taking measurements during bed temperature
// calibration.
- // #define BTC_PROBE_TEMP 30.0f
+ //#define BTC_PROBE_TEMP 30.0f
// Height above Z=0.0f to raise the nozzle. Lowering this can help the probe to heat faster.
// Note: the Z=0.0f offset is determined by the probe offset which can be set using M851.
- // #define PTC_PROBE_HEATING_OFFSET 0.5f
+ //#define PTC_PROBE_HEATING_OFFSET 0.5f
// Height to raise the Z-probe between heating and taking the next measurement. Some probes
// may fail to untrigger if they have been triggered for a long time, which can be solved by
// increasing the height the probe is raised to.
- // #define PTC_PROBE_RAISE 15U
+ //#define PTC_PROBE_RAISE 15U
// If the probe is outside of the defined range, use linear extrapolation using the closest
// point and the PTC_LINEAR_EXTRAPOLATION'th next point. E.g. if set to 4 it will use data[0]
// and data[4] to perform linear extrapolation for values below PTC_SAMPLE_START.
- // #define PTC_LINEAR_EXTRAPOLATION 4
+ //#define PTC_LINEAR_EXTRAPOLATION 4
#endif
#endif
--
GitLab