diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 59e2d5c723fcb6f10c8e47a27d6c4c3be0d1e41f..df435b970d62cae4903d0b7dfd29bbd0b5e702f4 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 43745fc5ba67602f65876fcb864835ce3cef977f..230554c340d486a0e03a3f6af7d191f6d999a01f 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/Marlin/src/lcd/language/language_en.h b/Marlin/src/lcd/language/language_en.h
index aa4770bfd568571906247dfa617d4af1634afff7..163f7e83a63253e77f5b812101e5ffd670614ff4 100644
--- a/Marlin/src/lcd/language/language_en.h
+++ b/Marlin/src/lcd/language/language_en.h
@@ -933,6 +933,9 @@
#ifndef MSG_BLTOUCH_MODE_ECHO
#define MSG_BLTOUCH_MODE_ECHO _UxGT("Report Drain")
#endif
+#ifndef MSG_BLTOUCH_MODE_CHANGE
+ #define MSG_BLTOUCH_MODE_CHANGE _UxGT("DANGER: Bad settings can cause damage! Proceed anyway?")
+#endif
#ifndef MSG_MANUAL_DEPLOY
#define MSG_MANUAL_DEPLOY _UxGT("Deploy Z-Probe")
#endif
diff --git a/Marlin/src/lcd/menu/menu_configuration.cpp b/Marlin/src/lcd/menu/menu_configuration.cpp
index 793490be102ab361517984d092deef9e50b18893..3e666d9f1401d667a6c3ed6b6800dcec57a48bf7 100644
--- a/Marlin/src/lcd/menu/menu_configuration.cpp
+++ b/Marlin/src/lcd/menu/menu_configuration.cpp
@@ -199,11 +199,19 @@ static void lcd_factory_settings() {
MENU_ITEM(function, MSG_BLTOUCH_STOW, bltouch._stow);
MENU_ITEM(function, MSG_BLTOUCH_SW_MODE, bltouch._set_SW_mode);
#if ENABLED(BLTOUCH_LCD_VOLTAGE_MENU)
- MENU_ITEM(function, MSG_BLTOUCH_5V_MODE, bltouch._set_5V_mode);
- MENU_ITEM(function, MSG_BLTOUCH_OD_MODE, bltouch._set_OD_mode);
+ MENU_ITEM(submenu, MSG_BLTOUCH_5V_MODE, []{
+ do_select_screen(PSTR(MSG_BLTOUCH_5V_MODE), PSTR(MSG_BUTTON_CANCEL), bltouch._set_5V_mode, ui.goto_previous_screen, PSTR(MSG_BLTOUCH_MODE_CHANGE));
+ });
+ MENU_ITEM(submenu, MSG_BLTOUCH_OD_MODE, []{
+ do_select_screen(PSTR(MSG_BLTOUCH_OD_MODE), PSTR(MSG_BUTTON_CANCEL), bltouch._set_OD_mode, ui.goto_previous_screen, PSTR(MSG_BLTOUCH_MODE_CHANGE));
+ });
MENU_ITEM(function, MSG_BLTOUCH_MODE_STORE, bltouch._mode_store);
- MENU_ITEM(function, MSG_BLTOUCH_MODE_STORE_5V, bltouch.mode_conv_5V);
- MENU_ITEM(function, MSG_BLTOUCH_MODE_STORE_OD, bltouch.mode_conv_OD);
+ MENU_ITEM(submenu, MSG_BLTOUCH_MODE_STORE_5V, []{
+ do_select_screen(PSTR(MSG_BLTOUCH_MODE_STORE_5V), PSTR(MSG_BUTTON_CANCEL), bltouch.mode_conv_5V, ui.goto_previous_screen, PSTR(MSG_BLTOUCH_MODE_CHANGE));
+ });
+ MENU_ITEM(submenu, MSG_BLTOUCH_MODE_STORE_OD, []{
+ do_select_screen(PSTR(MSG_BLTOUCH_MODE_STORE_OD), PSTR(MSG_BUTTON_CANCEL), bltouch.mode_conv_OD, ui.goto_previous_screen, PSTR(MSG_BLTOUCH_MODE_CHANGE));
+ });
MENU_ITEM(function, MSG_BLTOUCH_MODE_ECHO, bltouch_report);
#endif
END_MENU();
diff --git a/Marlin/src/lcd/ultralcd.cpp b/Marlin/src/lcd/ultralcd.cpp
index 855be5bce2eea36717da747511d94799ff5dae00..4822ebd2d77d1cc6f1d0ef94166d1a6807c08455 100644
--- a/Marlin/src/lcd/ultralcd.cpp
+++ b/Marlin/src/lcd/ultralcd.cpp
@@ -196,10 +196,39 @@ millis_t next_button_update_ms;
#endif
- void _wrap_string(uint8_t &x, uint8_t &y, const char * const string, read_byte_cb_t cb_read_byte) {
+ void _wrap_string(uint8_t &x, uint8_t &y, const char * const string, read_byte_cb_t cb_read_byte, bool wordwrap/*=false*/) {
SETCURSOR(x, y);
- if (string) {
- uint8_t *p = (uint8_t*)string;
+ if (!string) return;
+
+ uint8_t *p = (uint8_t*)string;
+ if (wordwrap) {
+ uint8_t *wrd = p, c = 0;
+ for (;;) {
+ wchar_t ch;
+ p = get_utf8_value_cb(p, cb_read_byte, &ch);
+ const bool eol = !ch;
+ if (eol || ch == ' ' || ch == '-' || ch == '+' || ch == '.') {
+ if (!c && ch == ' ') continue; // collapse extra spaces
+ if (x + c > LCD_WIDTH && c < (LCD_WIDTH) * 3 / 4) { // should it wrap?
+ x = 0; y++; // move x to string len (plus space)
+ SETCURSOR(0, y); // simulate carriage return
+ }
+ c += !eol; // +1 so the space will be printed
+ x += c; // advance x to new position
+ while (c--) { // character countdown
+ wrd = get_utf8_value_cb(wrd, cb_read_byte, &ch); // get characters again
+ lcd_put_wchar(ch); // word (plus space) to the LCD
+ }
+ if (eol) break; // all done
+ wrd = nullptr; // set up for next word
+ }
+ else {
+ if (!wrd) wrd = p; // starting a new word?
+ c++; // count word characters
+ }
+ }
+ }
+ else {
for (;;) {
wchar_t ch;
p = get_utf8_value_cb(p, cb_read_byte, &ch);
@@ -221,7 +250,7 @@ millis_t next_button_update_ms;
x = (LCD_WIDTH - plen - slen) / 2;
y = LCD_HEIGHT > 3 ? 1 : 0;
}
- wrap_string_P(x, y, pref);
+ wrap_string_P(x, y, pref, true);
if (string) {
if (x) { x = 0; y++; } // Move to the start of the next line
wrap_string(x, y, string);
diff --git a/Marlin/src/lcd/ultralcd.h b/Marlin/src/lcd/ultralcd.h
index 630539a986703f34bab7f5bebba817accd23c546..97c87dfe111409b3a8f12e3a96a99903bdbeeefc 100644
--- a/Marlin/src/lcd/ultralcd.h
+++ b/Marlin/src/lcd/ultralcd.h
@@ -74,9 +74,9 @@
#include "fontutils.h"
- void _wrap_string(uint8_t &x, uint8_t &y, const char * const string, read_byte_cb_t cb_read_byte);
- inline void wrap_string_P(uint8_t &x, uint8_t &y, PGM_P const pstr) { _wrap_string(x, y, pstr, read_byte_rom); }
- inline void wrap_string(uint8_t &x, uint8_t &y, const char * const string) { _wrap_string(x, y, string, read_byte_ram); }
+ void _wrap_string(uint8_t &x, uint8_t &y, const char * const string, read_byte_cb_t cb_read_byte, const bool wordwrap=false);
+ inline void wrap_string_P(uint8_t &x, uint8_t &y, PGM_P const pstr, const bool wordwrap=false) { _wrap_string(x, y, pstr, read_byte_rom, wordwrap); }
+ inline void wrap_string(uint8_t &x, uint8_t &y, const char * const string, const bool wordwrap=false) { _wrap_string(x, y, string, read_byte_ram, wordwrap); }
#if ENABLED(SDSUPPORT)
#include "../sd/cardreader.h"
diff --git a/config/default/Configuration.h b/config/default/Configuration.h
index 59e2d5c723fcb6f10c8e47a27d6c4c3be0d1e41f..df435b970d62cae4903d0b7dfd29bbd0b5e702f4 100644
--- a/config/default/Configuration.h
+++ b/config/default/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/default/Configuration_adv.h b/config/default/Configuration_adv.h
index 9071fc039de52376d8f22004bb6bcca650ec35ff..6dbcbf1b8c174827cb19370239459b5488149e9c 100644
--- a/config/default/Configuration_adv.h
+++ b/config/default/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/3DFabXYZ/Migbot/Configuration.h b/config/examples/3DFabXYZ/Migbot/Configuration.h
index bea7102db43818342626e3cf5033b49112f3a52d..3af58dea1ab6c7fd97b47f04b38980c4e981fda9 100644
--- a/config/examples/3DFabXYZ/Migbot/Configuration.h
+++ b/config/examples/3DFabXYZ/Migbot/Configuration.h
@@ -834,72 +834,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
index 21a8cdfa33072467567a6642047dea09f93bd6db..f48d7398069d8b5c802ff3274a4109d0776e7b78 100644
--- a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
+++ b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/AlephObjects/TAZ4/Configuration.h b/config/examples/AlephObjects/TAZ4/Configuration.h
index 3dbed3611f8d2e25618dd44614245cc69af263fd..0d83bc6fa0a869e41aae84c4746a01c073332caa 100644
--- a/config/examples/AlephObjects/TAZ4/Configuration.h
+++ b/config/examples/AlephObjects/TAZ4/Configuration.h
@@ -848,72 +848,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/config/examples/AlephObjects/TAZ4/Configuration_adv.h
index 13ff792a45190e0891368120257f43e368dd0f40..b49e93cd6598b725ead7bdb2a6b769574af24fd2 100644
--- a/config/examples/AlephObjects/TAZ4/Configuration_adv.h
+++ b/config/examples/AlephObjects/TAZ4/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/AliExpress/CL-260/Configuration.h b/config/examples/AliExpress/CL-260/Configuration.h
index 30a00a902198362d93bb082094a2ee40ad001ea2..5a176a46a245ba022cbe3b148300bc6d66d2608c 100644
--- a/config/examples/AliExpress/CL-260/Configuration.h
+++ b/config/examples/AliExpress/CL-260/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/AliExpress/UM2pExt/Configuration.h b/config/examples/AliExpress/UM2pExt/Configuration.h
index 063a7763f3257f431290141ddaac210c7f4385b1..dd8b032909e483e494926591c0ef02cc3fef473d 100644
--- a/config/examples/AliExpress/UM2pExt/Configuration.h
+++ b/config/examples/AliExpress/UM2pExt/Configuration.h
@@ -839,72 +839,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/AliExpress/UM2pExt/Configuration_adv.h b/config/examples/AliExpress/UM2pExt/Configuration_adv.h
index fff92af616855acec76e1c12868f48b457cc3a1d..df85efde7ce6a17735cd25440862012c383e08eb 100644
--- a/config/examples/AliExpress/UM2pExt/Configuration_adv.h
+++ b/config/examples/AliExpress/UM2pExt/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Anet/A2/Configuration.h b/config/examples/Anet/A2/Configuration.h
index 0e266313610dd45c73fe735aa7e16ec71178e17d..d0f906a658b6d3de8836cc7869313540332889b5 100644
--- a/config/examples/Anet/A2/Configuration.h
+++ b/config/examples/Anet/A2/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Anet/A2/Configuration_adv.h b/config/examples/Anet/A2/Configuration_adv.h
index 1ec40e83023790aa6a1f599c5e170d26d1ba6289..65e599a8b719cc2ab6fa4327fce94f2dbf01dbf8 100644
--- a/config/examples/Anet/A2/Configuration_adv.h
+++ b/config/examples/Anet/A2/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Anet/A2plus/Configuration.h b/config/examples/Anet/A2plus/Configuration.h
index 58a363950c4d86d55f97d684b7d8b086c4315482..5f7ba36a8241d7c3d6c8e5c8dc0fa2a485f7fbcb 100644
--- a/config/examples/Anet/A2plus/Configuration.h
+++ b/config/examples/Anet/A2plus/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Anet/A2plus/Configuration_adv.h b/config/examples/Anet/A2plus/Configuration_adv.h
index 1ec40e83023790aa6a1f599c5e170d26d1ba6289..65e599a8b719cc2ab6fa4327fce94f2dbf01dbf8 100644
--- a/config/examples/Anet/A2plus/Configuration_adv.h
+++ b/config/examples/Anet/A2plus/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Anet/A6/Configuration.h b/config/examples/Anet/A6/Configuration.h
index 1f27ff610f3d50e54a8e7fa5f326fd5790ecb534..9f84b89cb7751a46c4440c01d3bf86a22dfb37d1 100644
--- a/config/examples/Anet/A6/Configuration.h
+++ b/config/examples/Anet/A6/Configuration.h
@@ -875,72 +875,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Anet/A6/Configuration_adv.h b/config/examples/Anet/A6/Configuration_adv.h
index 5d3fae65d2e5a4a1ef53b50cffb7b053af31abdf..6560ed41240502fc8bb478a4835e69cba7213743 100644
--- a/config/examples/Anet/A6/Configuration_adv.h
+++ b/config/examples/Anet/A6/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Anet/A8/Configuration.h b/config/examples/Anet/A8/Configuration.h
index 23d14e7bc7708c686a4426fd27ce8d336413e3e6..df687c95f09eb1f6d62046f8b13088eb5dfa1eaa 100644
--- a/config/examples/Anet/A8/Configuration.h
+++ b/config/examples/Anet/A8/Configuration.h
@@ -841,72 +841,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Anet/A8/Configuration_adv.h b/config/examples/Anet/A8/Configuration_adv.h
index c76c6be3d96e60fc4670e08c31437aae3a914e06..771107dc485022de120a5b3e8885b75920cdde39 100644
--- a/config/examples/Anet/A8/Configuration_adv.h
+++ b/config/examples/Anet/A8/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Anet/A8plus/Configuration.h b/config/examples/Anet/A8plus/Configuration.h
index 1bec886b937ee7b621ac2a61791dc956d95100f5..5ad6b5d60e9caaa79d5d1375ecf58625d9a9ee7e 100644
--- a/config/examples/Anet/A8plus/Configuration.h
+++ b/config/examples/Anet/A8plus/Configuration.h
@@ -839,72 +839,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Anet/A8plus/Configuration_adv.h b/config/examples/Anet/A8plus/Configuration_adv.h
index d238fab4ffd14ee01dc213afda950ca16662e5c7..aa066ceea26d52eb51d066d636c3a46ad06f96f6 100644
--- a/config/examples/Anet/A8plus/Configuration_adv.h
+++ b/config/examples/Anet/A8plus/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Anet/E16/Configuration.h b/config/examples/Anet/E16/Configuration.h
index 421ea5b4fc9ead1b9928b63884e3039cf31f0394..90fa55db1927928b0d3e2fbe88c4b785d812f8e3 100644
--- a/config/examples/Anet/E16/Configuration.h
+++ b/config/examples/Anet/E16/Configuration.h
@@ -840,72 +840,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- #define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Anet/E16/Configuration_adv.h b/config/examples/Anet/E16/Configuration_adv.h
index 198ced9d6ee630cb5d4908c49433deae6802ad4c..23f33641c52de1e7eb4744912751b73065ced391 100644
--- a/config/examples/Anet/E16/Configuration_adv.h
+++ b/config/examples/Anet/E16/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/AnyCubic/i3/Configuration.h b/config/examples/AnyCubic/i3/Configuration.h
index f95ffdbf28919c3cf88616836965583786191eae..1d91086baf65ba086efaf95bdc8e9d5f2ab619b4 100644
--- a/config/examples/AnyCubic/i3/Configuration.h
+++ b/config/examples/AnyCubic/i3/Configuration.h
@@ -838,72 +838,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/AnyCubic/i3/Configuration_adv.h b/config/examples/AnyCubic/i3/Configuration_adv.h
index 63eeeaa9882cc8cb4600ecde0613e07046647bc4..488a816a1c2bf675a0ef407e5ab35b0534bc7094 100644
--- a/config/examples/AnyCubic/i3/Configuration_adv.h
+++ b/config/examples/AnyCubic/i3/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/ArmEd/Configuration.h b/config/examples/ArmEd/Configuration.h
index 06192db5065dbe16791089a3254d3931c0c83968..745eef0e61bb09f6ba4a3f9d44e07050f73ecd72 100644
--- a/config/examples/ArmEd/Configuration.h
+++ b/config/examples/ArmEd/Configuration.h
@@ -829,72 +829,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/ArmEd/Configuration_adv.h b/config/examples/ArmEd/Configuration_adv.h
index 68af2824d4b95347fbf7c44e2f1b11a8b961ee92..6b5d2377cefda511ccdd756ebbfd3e4ad9886f96 100644
--- a/config/examples/ArmEd/Configuration_adv.h
+++ b/config/examples/ArmEd/Configuration_adv.h
@@ -528,6 +528,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Azteeg/X5GT/Configuration.h b/config/examples/Azteeg/X5GT/Configuration.h
index 9b0fdd0ead493d067a1f48a477f587375c9eb8b6..6319a44a52d948ce31223f88258990110e5bbc79 100644
--- a/config/examples/Azteeg/X5GT/Configuration.h
+++ b/config/examples/Azteeg/X5GT/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration.h b/config/examples/BIBO/TouchX/cyclops/Configuration.h
index 7786c5eacb6024512097dbd1e0877d742b543edf..53bd514bc7ddea187cfdfd76a549c4bcfa4dd8da 100644
--- a/config/examples/BIBO/TouchX/cyclops/Configuration.h
+++ b/config/examples/BIBO/TouchX/cyclops/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
index 827d7e6739ccf85d2fbaadf9b051dfdb3f9423ed..ee6e68d2ba798f2169754a08bce72f95b60f1e31 100644
--- a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
+++ b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/BIBO/TouchX/default/Configuration.h b/config/examples/BIBO/TouchX/default/Configuration.h
index 7a235f338c1a57a6b54dacb82dfb84cd39e7bae4..4f84b61991a7d57835f44467ef8b00b84bb80666 100644
--- a/config/examples/BIBO/TouchX/default/Configuration.h
+++ b/config/examples/BIBO/TouchX/default/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/BIBO/TouchX/default/Configuration_adv.h b/config/examples/BIBO/TouchX/default/Configuration_adv.h
index 7ee6de9fb4c1b3ef0ad8a3aad6fbacf48b2277d6..8b703d0cbf464835ea812dcdc208a56d3ed5b41a 100644
--- a/config/examples/BIBO/TouchX/default/Configuration_adv.h
+++ b/config/examples/BIBO/TouchX/default/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/BQ/Hephestos/Configuration.h b/config/examples/BQ/Hephestos/Configuration.h
index fe71a04a4bbc793b647dc0ca13029ff136c9291a..7044c4f3c05332f9e7de6d9c3cb3c75ce5e9cf1b 100644
--- a/config/examples/BQ/Hephestos/Configuration.h
+++ b/config/examples/BQ/Hephestos/Configuration.h
@@ -816,72 +816,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/BQ/Hephestos/Configuration_adv.h b/config/examples/BQ/Hephestos/Configuration_adv.h
index 02a00778b79df2fdf2adac0cb736b827688d97ef..c0d0fd3344694600175ec5607dbef9068e9abd1c 100644
--- a/config/examples/BQ/Hephestos/Configuration_adv.h
+++ b/config/examples/BQ/Hephestos/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/BQ/Hephestos_2/Configuration.h b/config/examples/BQ/Hephestos_2/Configuration.h
index 51c5acb53ed93e3e4554e8b639a486a20805d9f9..a90e9bde5eb9bd1cc218f58001546ec5abb0cb7e 100644
--- a/config/examples/BQ/Hephestos_2/Configuration.h
+++ b/config/examples/BQ/Hephestos_2/Configuration.h
@@ -829,72 +829,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/BQ/Hephestos_2/Configuration_adv.h b/config/examples/BQ/Hephestos_2/Configuration_adv.h
index 0db2836a1dcd71282f4abf63c4e66925014ad53b..7cf39987560c6ee6726d2e4cd8bf24ffb06d1288 100644
--- a/config/examples/BQ/Hephestos_2/Configuration_adv.h
+++ b/config/examples/BQ/Hephestos_2/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/BQ/WITBOX/Configuration.h b/config/examples/BQ/WITBOX/Configuration.h
index eff8a4ab2d4d98b63b4dd84736e89a9f9c37f3f0..80f2f675b98b28240257346a3eb94e2422e5dfec 100644
--- a/config/examples/BQ/WITBOX/Configuration.h
+++ b/config/examples/BQ/WITBOX/Configuration.h
@@ -816,72 +816,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/BQ/WITBOX/Configuration_adv.h b/config/examples/BQ/WITBOX/Configuration_adv.h
index 02a00778b79df2fdf2adac0cb736b827688d97ef..c0d0fd3344694600175ec5607dbef9068e9abd1c 100644
--- a/config/examples/BQ/WITBOX/Configuration_adv.h
+++ b/config/examples/BQ/WITBOX/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Cartesio/Configuration.h b/config/examples/Cartesio/Configuration.h
index 183d07f16edb2030c614d83ec54f3eb13ef0e2d3..f07dbd777cdea09e13b1f5a1174b122a008f4310 100644
--- a/config/examples/Cartesio/Configuration.h
+++ b/config/examples/Cartesio/Configuration.h
@@ -827,72 +827,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Cartesio/Configuration_adv.h b/config/examples/Cartesio/Configuration_adv.h
index ed521882808ac75d840c4ff082d097ee389aef71..5014ec87ce4dd2b001b47eac0a498c610c61e715 100644
--- a/config/examples/Cartesio/Configuration_adv.h
+++ b/config/examples/Cartesio/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Creality/CR-10/Configuration.h b/config/examples/Creality/CR-10/Configuration.h
index 084e267136e68f6fd7c42a8c5c0f6d5ad47c70bd..c1131af1984670ceae67a163d4c0bfeb84b6d56b 100644
--- a/config/examples/Creality/CR-10/Configuration.h
+++ b/config/examples/Creality/CR-10/Configuration.h
@@ -838,72 +838,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- #define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Creality/CR-10/Configuration_adv.h b/config/examples/Creality/CR-10/Configuration_adv.h
index d9f5511fc9e0d3e2b4f2e4e9f5e008588044edc9..04be986a9b989f90d613f9f4770c14b371eede4f 100644
--- a/config/examples/Creality/CR-10/Configuration_adv.h
+++ b/config/examples/Creality/CR-10/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ #define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Creality/CR-10S/Configuration.h b/config/examples/Creality/CR-10S/Configuration.h
index 9114a9cabb69973117435be1ad2ba762fd44bfc0..4a9e6ad4a63b8c6c04e61369abb526abdd19e432 100644
--- a/config/examples/Creality/CR-10S/Configuration.h
+++ b/config/examples/Creality/CR-10S/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- #define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Creality/CR-10S/Configuration_adv.h b/config/examples/Creality/CR-10S/Configuration_adv.h
index 7398e86cd8c7cc9fc73fa8b4cc8d1f825a9ce399..3fe1ad00771d8789413b3154049b91eee93a2478 100644
--- a/config/examples/Creality/CR-10S/Configuration_adv.h
+++ b/config/examples/Creality/CR-10S/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ #define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Creality/CR-10_5S/Configuration.h b/config/examples/Creality/CR-10_5S/Configuration.h
index 18134f02a0133882e120796d8a0334a66883c07f..58b8c9388772b66245142760c84a1b11270c3319 100644
--- a/config/examples/Creality/CR-10_5S/Configuration.h
+++ b/config/examples/Creality/CR-10_5S/Configuration.h
@@ -829,72 +829,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- #define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Creality/CR-10_5S/Configuration_adv.h b/config/examples/Creality/CR-10_5S/Configuration_adv.h
index ba85698c1f9bf74448400ed0142091a48a627dbb..544a902d42e0a51ec515a0c2932ffe7a10662edd 100644
--- a/config/examples/Creality/CR-10_5S/Configuration_adv.h
+++ b/config/examples/Creality/CR-10_5S/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ #define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Creality/CR-10mini/Configuration.h b/config/examples/Creality/CR-10mini/Configuration.h
index 1ed070a2cbd1cf585eb613e38586850683f51c9f..fe2a11c799f715f9e1aa13d8420a3eabadd30ff8 100644
--- a/config/examples/Creality/CR-10mini/Configuration.h
+++ b/config/examples/Creality/CR-10mini/Configuration.h
@@ -847,72 +847,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- #define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Creality/CR-10mini/Configuration_adv.h b/config/examples/Creality/CR-10mini/Configuration_adv.h
index 728fdccce2524d57f5ad60e8f58725742d401330..bffa39f5fbe963fd396069f390e9f943947f3e83 100644
--- a/config/examples/Creality/CR-10mini/Configuration_adv.h
+++ b/config/examples/Creality/CR-10mini/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ #define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Creality/CR-8/Configuration.h b/config/examples/Creality/CR-8/Configuration.h
index 4387cb7dd23eb99311683c6c0fe2260d92cae6f1..a857ba8cffa9dd35cae2d96fe782316c3d186694 100644
--- a/config/examples/Creality/CR-8/Configuration.h
+++ b/config/examples/Creality/CR-8/Configuration.h
@@ -838,72 +838,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- #define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Creality/CR-8/Configuration_adv.h b/config/examples/Creality/CR-8/Configuration_adv.h
index b76760495ea9acad0ab63970793701552a13dd7b..7a6898edd14d0c717ab93ebc1eebf21daf155c61 100644
--- a/config/examples/Creality/CR-8/Configuration_adv.h
+++ b/config/examples/Creality/CR-8/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ #define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Creality/Ender-2/Configuration.h b/config/examples/Creality/Ender-2/Configuration.h
index 60a7896543dbb152a3ea5e54343af07daf6252a4..858e7acdda203a586d5ca0d6b4921036a6c87e0e 100644
--- a/config/examples/Creality/Ender-2/Configuration.h
+++ b/config/examples/Creality/Ender-2/Configuration.h
@@ -832,72 +832,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- #define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Creality/Ender-2/Configuration_adv.h b/config/examples/Creality/Ender-2/Configuration_adv.h
index cb191e69ec6817f574124297c325fb99e84a1d93..9d83e720cd85d745a2c2c1cdd32d3bfc8a724643 100644
--- a/config/examples/Creality/Ender-2/Configuration_adv.h
+++ b/config/examples/Creality/Ender-2/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ #define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Creality/Ender-3/Configuration.h b/config/examples/Creality/Ender-3/Configuration.h
index dc35f673874dcb86552078d936f346cfe397c4fa..005d37c39868f547843ef4f01c8995506284fa8c 100644
--- a/config/examples/Creality/Ender-3/Configuration.h
+++ b/config/examples/Creality/Ender-3/Configuration.h
@@ -832,72 +832,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- #define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Creality/Ender-3/Configuration_adv.h b/config/examples/Creality/Ender-3/Configuration_adv.h
index c3a3df2e773b5e84b771b83caaa2b16e524c7fd6..e2fa33e62e19642a4d529acf42ca5020ed265bd1 100644
--- a/config/examples/Creality/Ender-3/Configuration_adv.h
+++ b/config/examples/Creality/Ender-3/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ #define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Creality/Ender-4/Configuration.h b/config/examples/Creality/Ender-4/Configuration.h
index 79956cd9223d35ed00c9156cac9a05c8ea55b464..4563046fce5010234dbdecad1907580d78919abd 100644
--- a/config/examples/Creality/Ender-4/Configuration.h
+++ b/config/examples/Creality/Ender-4/Configuration.h
@@ -838,72 +838,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- #define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Creality/Ender-4/Configuration_adv.h b/config/examples/Creality/Ender-4/Configuration_adv.h
index 8237bd67a711194eede3969940357f8783579bc8..2e522a4f9234cd54bb260cee230b9d03e1b3f551 100644
--- a/config/examples/Creality/Ender-4/Configuration_adv.h
+++ b/config/examples/Creality/Ender-4/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ #define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h
index fc58eb5db53aed90fdb924de48e7aed7692b0617..6ee802596aa4f05b3be36d36f100ff817752ed49 100644
--- a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h
+++ b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h
@@ -523,6 +523,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Einstart-S/Configuration.h b/config/examples/Einstart-S/Configuration.h
index a2dbc91bd31c9770c41b69c105d48f9f7c67c8f2..20b8de96660f628c8834388dda54cabb8bfe32ea 100644
--- a/config/examples/Einstart-S/Configuration.h
+++ b/config/examples/Einstart-S/Configuration.h
@@ -837,72 +837,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Einstart-S/Configuration_adv.h b/config/examples/Einstart-S/Configuration_adv.h
index b8a39e85946c4e2a3033a1e24b55a9f6b13663ff..236b558af380df1d575d0755fb5a7aac3d2c7133 100644
--- a/config/examples/Einstart-S/Configuration_adv.h
+++ b/config/examples/Einstart-S/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Felix/Configuration.h b/config/examples/Felix/Configuration.h
index f96aceb1997c8afa1fff1f19ecdfc9932f809d0d..c5e2281ee10c4dadd95344de988ffb1d35236f92 100644
--- a/config/examples/Felix/Configuration.h
+++ b/config/examples/Felix/Configuration.h
@@ -810,72 +810,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Felix/Configuration_adv.h b/config/examples/Felix/Configuration_adv.h
index ca71afd9dca7c50145d543a1f2bbef8fe69e3a21..0afa0c900565c0b21dc20f5e42a70b81b9dccd4c 100644
--- a/config/examples/Felix/Configuration_adv.h
+++ b/config/examples/Felix/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Felix/DUAL/Configuration.h b/config/examples/Felix/DUAL/Configuration.h
index bebc6669b05e4a055ea7e62c0a87f55431e4ce48..b53442d1f802f513c45274c41b5db91c8a5d7d35 100644
--- a/config/examples/Felix/DUAL/Configuration.h
+++ b/config/examples/Felix/DUAL/Configuration.h
@@ -810,72 +810,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/FlashForge/CreatorPro/Configuration.h b/config/examples/FlashForge/CreatorPro/Configuration.h
index 7b9388f959203a1d3a6a8692babda49f90af7dab..ec8be7e1e66b280652fa0d4b2cc74353f3bdab40 100644
--- a/config/examples/FlashForge/CreatorPro/Configuration.h
+++ b/config/examples/FlashForge/CreatorPro/Configuration.h
@@ -820,72 +820,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/FlashForge/CreatorPro/Configuration_adv.h b/config/examples/FlashForge/CreatorPro/Configuration_adv.h
index 841caaad30d4a29378160b5b9c76554fe568aa19..68fc6ad2be41ab69d4600f92a081101673cef28f 100644
--- a/config/examples/FlashForge/CreatorPro/Configuration_adv.h
+++ b/config/examples/FlashForge/CreatorPro/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/FolgerTech/i3-2020/Configuration.h b/config/examples/FolgerTech/i3-2020/Configuration.h
index 1d0af2e040e0eaf4752569f94c62b108447c4a59..393f537519c3266b3a07eb7588d52eac5e0f77ff 100644
--- a/config/examples/FolgerTech/i3-2020/Configuration.h
+++ b/config/examples/FolgerTech/i3-2020/Configuration.h
@@ -834,72 +834,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/config/examples/FolgerTech/i3-2020/Configuration_adv.h
index d944a42ccfa08801f3856698f2481a733f898972..d13a1a0f33d593b843b864ac70871ca6e6cde3bc 100644
--- a/config/examples/FolgerTech/i3-2020/Configuration_adv.h
+++ b/config/examples/FolgerTech/i3-2020/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Formbot/Raptor/Configuration.h b/config/examples/Formbot/Raptor/Configuration.h
index f1c8827314c1a4eea2606d2ef64047380c467d6c..2a14aa057a530835fe696531ddd8a8dfe9a59ff3 100644
--- a/config/examples/Formbot/Raptor/Configuration.h
+++ b/config/examples/Formbot/Raptor/Configuration.h
@@ -911,72 +911,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Formbot/Raptor/Configuration_adv.h b/config/examples/Formbot/Raptor/Configuration_adv.h
index 4b8fa791303f74e8067d93228a84127558b3a339..f2f1abab30737a95b1d2ca1721c1731a37d96f0d 100644
--- a/config/examples/Formbot/Raptor/Configuration_adv.h
+++ b/config/examples/Formbot/Raptor/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Formbot/T_Rex_2+/Configuration.h b/config/examples/Formbot/T_Rex_2+/Configuration.h
index 4ad9878baf7c2d38653f6a0ddf2a03482a9098bb..bd7b0c71d5b5c286f558461d69531a3bfe6b8c2f 100644
--- a/config/examples/Formbot/T_Rex_2+/Configuration.h
+++ b/config/examples/Formbot/T_Rex_2+/Configuration.h
@@ -857,73 +857,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
-
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
index a1ce10b561657d9a9bf1618e4f5e7129dbe86ef2..06697ae4f973277c2f9ba7f6c0ca3a35e84efd1b 100644
--- a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
+++ b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
@@ -528,6 +528,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Formbot/T_Rex_3/Configuration.h b/config/examples/Formbot/T_Rex_3/Configuration.h
index ee017eb999a0b9b28d82667251f800d434aeca44..6e23032a667113d713b7a2a0aef64f6deb3b58e3 100644
--- a/config/examples/Formbot/T_Rex_3/Configuration.h
+++ b/config/examples/Formbot/T_Rex_3/Configuration.h
@@ -844,72 +844,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Formbot/T_Rex_3/Configuration_adv.h b/config/examples/Formbot/T_Rex_3/Configuration_adv.h
index a89436a711bb575e2c227a3faa78916bb22be866..13d34be030054f8ab47d539bc64b19d918b4c207 100644
--- a/config/examples/Formbot/T_Rex_3/Configuration_adv.h
+++ b/config/examples/Formbot/T_Rex_3/Configuration_adv.h
@@ -528,6 +528,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Geeetech/A10M/Configuration.h b/config/examples/Geeetech/A10M/Configuration.h
index 52977241f2aa94dde03fe0e571ddb0bd775c64b6..2bd10d91c7f8428887f2a8814311137fd6811c6b 100644
--- a/config/examples/Geeetech/A10M/Configuration.h
+++ b/config/examples/Geeetech/A10M/Configuration.h
@@ -811,72 +811,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- #define BLTOUCH_DELAY 200
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- #define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Geeetech/A10M/Configuration_adv.h b/config/examples/Geeetech/A10M/Configuration_adv.h
index 8c3f351f058950cb6831c48f2ee6686f623adfe1..ba24826da53cd595e63582d88523b8eef9a7f5e5 100644
--- a/config/examples/Geeetech/A10M/Configuration_adv.h
+++ b/config/examples/Geeetech/A10M/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ #define BLTOUCH_DELAY 200
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ #define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Geeetech/A20M/Configuration.h b/config/examples/Geeetech/A20M/Configuration.h
index e4e4932769e4694961e3d681dc1f22fe37d99f05..9813957f05522e82e89fe633b29f57b3cb5b00eb 100644
--- a/config/examples/Geeetech/A20M/Configuration.h
+++ b/config/examples/Geeetech/A20M/Configuration.h
@@ -811,72 +811,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- #define BLTOUCH_DELAY 200
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- #define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Geeetech/A20M/Configuration_adv.h b/config/examples/Geeetech/A20M/Configuration_adv.h
index 4c3d1fb9fc3d6b1db7a75a35861c9712f444a967..77ab799829fe67f601bd6c6253e749e6fb44b8c7 100644
--- a/config/examples/Geeetech/A20M/Configuration_adv.h
+++ b/config/examples/Geeetech/A20M/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ #define BLTOUCH_DELAY 200
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ #define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Geeetech/GT2560/Configuration.h b/config/examples/Geeetech/GT2560/Configuration.h
index 8de0a2dcb204f8ceba9bd2f2e388d01cef3cbb0a..973bbc145bf1ffccae1bda094da628ede03b4863 100644
--- a/config/examples/Geeetech/GT2560/Configuration.h
+++ b/config/examples/Geeetech/GT2560/Configuration.h
@@ -843,72 +843,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
index a016c8f317b909d1ab99507e93af7e9fa00d0925..111a37527e621bf3111f7031f56df371d4a89848 100644
--- a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
+++ b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
@@ -828,9 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- //#define BLTOUCH_DELAY 500 // Minimum Command delay (ms). Enable and increase if needed
-#endif
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Geeetech/MeCreator2/Configuration.h b/config/examples/Geeetech/MeCreator2/Configuration.h
index ffb52c2ecb1c1d568a3a9c53e3d79a85b1c0bb1a..47f355c89e5556c1db46432fbbd9417613ad1e86 100644
--- a/config/examples/Geeetech/MeCreator2/Configuration.h
+++ b/config/examples/Geeetech/MeCreator2/Configuration.h
@@ -835,72 +835,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Geeetech/MeCreator2/Configuration_adv.h b/config/examples/Geeetech/MeCreator2/Configuration_adv.h
index 75a12a4f2179794dcbf2d4355cb87621aa56ce45..637dc90e5e8887c781797232769bcdfeef9bf766 100644
--- a/config/examples/Geeetech/MeCreator2/Configuration_adv.h
+++ b/config/examples/Geeetech/MeCreator2/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h
index 86ab601ae1e73bb22a0f463f5ffaa2f788bcfa79..159aea681a652e18679ac117cf89d0cdfa7c2db5 100644
--- a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h
+++ b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h
@@ -848,72 +848,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h
index 84344b89bbc8e9847cecb3f63ff25909534b5380..110687f3eec1c5e333b2565c5924959388955ab1 100644
--- a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h
+++ b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h
@@ -848,72 +848,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h
index c880f60fa82f716e6981c7b3f8737b5558a60635..6e105a185910506c40542e0b908f89bbab1b906c 100644
--- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h
+++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
index 25c3e596a01bf82d5999ca199af6157f12a48cf9..24bd6dec72d0dc306ff11c35cd2f11742b8f2715 100644
--- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
+++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h
index 4cc311fa6813030357b66272e8a2d51cb563eafa..37f0dd81d9c0b7ff8e568cece877b5971b9a6428 100644
--- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h
+++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
index 25c3e596a01bf82d5999ca199af6157f12a48cf9..24bd6dec72d0dc306ff11c35cd2f11742b8f2715 100644
--- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
+++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Infitary/i3-M508/Configuration.h b/config/examples/Infitary/i3-M508/Configuration.h
index 96d355da7664fd731bb038e319d0803b7e39cf84..a2d002baec87d1c43ecd0d3dc0f8a1dfd53a792d 100644
--- a/config/examples/Infitary/i3-M508/Configuration.h
+++ b/config/examples/Infitary/i3-M508/Configuration.h
@@ -832,72 +832,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Infitary/i3-M508/Configuration_adv.h b/config/examples/Infitary/i3-M508/Configuration_adv.h
index 24f6583edcb04c65e79d96aa0ae5196b117648d3..3aca50f504136042463dc06e562c2add0327296e 100644
--- a/config/examples/Infitary/i3-M508/Configuration_adv.h
+++ b/config/examples/Infitary/i3-M508/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/JGAurora/A5/Configuration.h b/config/examples/JGAurora/A5/Configuration.h
index 9067d6f5de1957f2d86d9ac07189df7458a5d63e..84286b7ee779897edeaae92af3cd51e3fe60493d 100644
--- a/config/examples/JGAurora/A5/Configuration.h
+++ b/config/examples/JGAurora/A5/Configuration.h
@@ -840,72 +840,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/JGAurora/A5/Configuration_adv.h b/config/examples/JGAurora/A5/Configuration_adv.h
index e2fe3b82fcc16bbdb82e9cd0cd1864d75300fdcc..5b9214622fce04ad744c498cc39edb9974acfca2 100644
--- a/config/examples/JGAurora/A5/Configuration_adv.h
+++ b/config/examples/JGAurora/A5/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/MakerParts/Configuration.h b/config/examples/MakerParts/Configuration.h
index a7665b5f7159af099a835aa3f4758c20de6a3246..8c0672b889afcfb7f760d12f5479d50e94d71be6 100644
--- a/config/examples/MakerParts/Configuration.h
+++ b/config/examples/MakerParts/Configuration.h
@@ -848,72 +848,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/MakerParts/Configuration_adv.h b/config/examples/MakerParts/Configuration_adv.h
index eecc6e9651b5fb74abf5ed5da0feca5bf6eb700b..9a80ce8f71da560e924a46e60454d7fcaa758d74 100644
--- a/config/examples/MakerParts/Configuration_adv.h
+++ b/config/examples/MakerParts/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Malyan/M150/Configuration.h b/config/examples/Malyan/M150/Configuration.h
index bd232317cf287649322b82235a6849d053c11e32..3c48103428bfcb7056135f34abb26293e2ed14be 100644
--- a/config/examples/Malyan/M150/Configuration.h
+++ b/config/examples/Malyan/M150/Configuration.h
@@ -848,72 +848,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Malyan/M150/Configuration_adv.h b/config/examples/Malyan/M150/Configuration_adv.h
index c70ebe90dc91cb5d899b04c7c31021fb027f320a..5ef26d1ebabe35c3742a6d9dddbffec43898230f 100644
--- a/config/examples/Malyan/M150/Configuration_adv.h
+++ b/config/examples/Malyan/M150/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Malyan/M200/Configuration.h b/config/examples/Malyan/M200/Configuration.h
index 16dc0a3ea0725e433362bae92f4df01f608a684e..4f1db1c15a18fbb33d05c6be82c29e2675dc6215 100644
--- a/config/examples/Malyan/M200/Configuration.h
+++ b/config/examples/Malyan/M200/Configuration.h
@@ -827,72 +827,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Malyan/M200/Configuration_adv.h b/config/examples/Malyan/M200/Configuration_adv.h
index 5f5b06ea6fd8a16a96eaa8b99da36606c54d3c4c..8eda23210d157d12da265240bbc3b9c67df23d68 100644
--- a/config/examples/Malyan/M200/Configuration_adv.h
+++ b/config/examples/Malyan/M200/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Micromake/C1/basic/Configuration.h b/config/examples/Micromake/C1/basic/Configuration.h
index a2ccf4fbdc7d7e3ead5c3a318453e3592b77c68d..dea50b5504027dacb118bbe54698134f2529d414 100644
--- a/config/examples/Micromake/C1/basic/Configuration.h
+++ b/config/examples/Micromake/C1/basic/Configuration.h
@@ -832,72 +832,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Micromake/C1/enhanced/Configuration.h b/config/examples/Micromake/C1/enhanced/Configuration.h
index fd78065ee82af17df3e4403614d86f3c265a9dd1..3d11f711ef8746e2326fcdbfd14ae9bf4df806cf 100644
--- a/config/examples/Micromake/C1/enhanced/Configuration.h
+++ b/config/examples/Micromake/C1/enhanced/Configuration.h
@@ -832,72 +832,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/config/examples/Micromake/C1/enhanced/Configuration_adv.h
index ec09312abcdb7208951ca30f0f97fa34a90f8821..7c5c1ca85fb56680aa16f07dda7c161b6be7d572 100644
--- a/config/examples/Micromake/C1/enhanced/Configuration_adv.h
+++ b/config/examples/Micromake/C1/enhanced/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Mks/Robin/Configuration.h b/config/examples/Mks/Robin/Configuration.h
index 0d851cd57c130d6a12b34243dd9259d790a31e31..0ebf3fb8aaad104b04dcb0e454d0a0cd2005246c 100644
--- a/config/examples/Mks/Robin/Configuration.h
+++ b/config/examples/Mks/Robin/Configuration.h
@@ -829,72 +829,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Mks/Robin/Configuration_adv.h b/config/examples/Mks/Robin/Configuration_adv.h
index f23b3089209ec664e0641c83215f49854d964962..26a98be8448062f961cea522991ccb64dd65705b 100644
--- a/config/examples/Mks/Robin/Configuration_adv.h
+++ b/config/examples/Mks/Robin/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Mks/Sbase/Configuration.h b/config/examples/Mks/Sbase/Configuration.h
index b14e6932900a03ac3d672de545c4fafb90d34e41..db5fc297b96853eafa7e091ea8ff4cca2c4c3abb 100644
--- a/config/examples/Mks/Sbase/Configuration.h
+++ b/config/examples/Mks/Sbase/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Mks/Sbase/Configuration_adv.h b/config/examples/Mks/Sbase/Configuration_adv.h
index 662a0d8d3a44a0b36f05a07a950228e386ffa44d..5a7997b2fba6dc85fb99153ec70b124c5a77a9a6 100644
--- a/config/examples/Mks/Sbase/Configuration_adv.h
+++ b/config/examples/Mks/Sbase/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Printrbot/PrintrboardG2/Configuration.h b/config/examples/Printrbot/PrintrboardG2/Configuration.h
index 1edb64ec410eb98f4cf5ae56914cb46f9a1e6962..ae5dd7d1df13d2b5d63087fdfab7cba3dd8084a8 100644
--- a/config/examples/Printrbot/PrintrboardG2/Configuration.h
+++ b/config/examples/Printrbot/PrintrboardG2/Configuration.h
@@ -836,72 +836,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/RapideLite/RL200/Configuration.h b/config/examples/RapideLite/RL200/Configuration.h
index e8a53840bd1f9cb35d2b8495190c1a60e84ad545..f57848c2777eacd02fbb8b8a0b59589df178b8ee 100644
--- a/config/examples/RapideLite/RL200/Configuration.h
+++ b/config/examples/RapideLite/RL200/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/RapideLite/RL200/Configuration_adv.h b/config/examples/RapideLite/RL200/Configuration_adv.h
index c900c72dc382b04cde4d9d5b4c862c68e5b64dea..b8e60c86884705953ce2cf6778e0bca66646de0f 100644
--- a/config/examples/RapideLite/RL200/Configuration_adv.h
+++ b/config/examples/RapideLite/RL200/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/RepRapPro/Huxley/Configuration.h b/config/examples/RepRapPro/Huxley/Configuration.h
index 46225f3e8deea8bb359b07a59a1d3927e4ab37d7..15d3ed1f81e72b44405d247b7cfe99c018a41dfd 100644
--- a/config/examples/RepRapPro/Huxley/Configuration.h
+++ b/config/examples/RepRapPro/Huxley/Configuration.h
@@ -868,72 +868,6 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/RepRapWorld/Megatronics/Configuration.h b/config/examples/RepRapWorld/Megatronics/Configuration.h
index 192501bef5e2f1e876c241a5f8145ee21ee6c46d..9d83db658e3ace3c71e3454f838728a633971c7a 100644
--- a/config/examples/RepRapWorld/Megatronics/Configuration.h
+++ b/config/examples/RepRapWorld/Megatronics/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/RigidBot/Configuration.h b/config/examples/RigidBot/Configuration.h
index 8ea8463e7561f08f87b4b49c37cdae24aac3993f..29dce6f9d231a38945da84140ec5dc5713d7b405 100644
--- a/config/examples/RigidBot/Configuration.h
+++ b/config/examples/RigidBot/Configuration.h
@@ -826,72 +826,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/RigidBot/Configuration_adv.h b/config/examples/RigidBot/Configuration_adv.h
index cabe70a7d9974ffdc7504bc0e2e2262a599c42a6..7d93b40490aab5500849a4766124b6d60fdb16d3 100644
--- a/config/examples/RigidBot/Configuration_adv.h
+++ b/config/examples/RigidBot/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/SCARA/Configuration.h b/config/examples/SCARA/Configuration.h
index 81219d09afe0bfd286e7d1cb42105fe50f1a2efe..9bc674c28103d8559405cf15bf79b509eaf97971 100644
--- a/config/examples/SCARA/Configuration.h
+++ b/config/examples/SCARA/Configuration.h
@@ -841,72 +841,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/SCARA/Configuration_adv.h b/config/examples/SCARA/Configuration_adv.h
index 6c372f6a0135f024f6c17f67922a88b69b2d8ec7..88d030c1ede389970db26140fa5a48f40163148c 100644
--- a/config/examples/SCARA/Configuration_adv.h
+++ b/config/examples/SCARA/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration.h b/config/examples/STM32/Black_STM32F407VET6/Configuration.h
index e194af9df9a340a956ba85d22ef70934c2f66cae..b237ce8b079c29e33ffacc11b4551843bb0157aa 100644
--- a/config/examples/STM32/Black_STM32F407VET6/Configuration.h
+++ b/config/examples/STM32/Black_STM32F407VET6/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
index 45b7ac97065499257569f4925f592c321609d663..d23ab4af143c956bd0940d7405d1d595f0a08385 100644
--- a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
+++ b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/STM32/STM32F10/Configuration.h b/config/examples/STM32/STM32F10/Configuration.h
index 858169b66059dd72a04656b5eb703169ff718a14..03d80f6177c30870dd06edee60ebf3bfd80ede6d 100644
--- a/config/examples/STM32/STM32F10/Configuration.h
+++ b/config/examples/STM32/STM32F10/Configuration.h
@@ -830,72 +830,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/STM32/STM32F4/Configuration.h b/config/examples/STM32/STM32F4/Configuration.h
index 1cfc9db2bd8314a88e7c109cbc26f175e20efafe..ba63e506f895eea344aa34a64dd52fa39313ea2c 100644
--- a/config/examples/STM32/STM32F4/Configuration.h
+++ b/config/examples/STM32/STM32F4/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/STM32/stm32f103ret6/Configuration.h b/config/examples/STM32/stm32f103ret6/Configuration.h
index 5ed1150cfbb2752ff88edd9318f47c7beacadb2c..1a7276a7f1efeabbb955ea8c17820b91c569bdbe 100644
--- a/config/examples/STM32/stm32f103ret6/Configuration.h
+++ b/config/examples/STM32/stm32f103ret6/Configuration.h
@@ -830,72 +830,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Sanguinololu/Configuration.h b/config/examples/Sanguinololu/Configuration.h
index 1cf2a61e679a8b747f246c9780ca26edfac01ad4..c87e2c70059794f4251075b17c66bf510731dab8 100644
--- a/config/examples/Sanguinololu/Configuration.h
+++ b/config/examples/Sanguinololu/Configuration.h
@@ -859,72 +859,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Sanguinololu/Configuration_adv.h b/config/examples/Sanguinololu/Configuration_adv.h
index 870f38b1bfc71ee38784ac9175f1334e60c4cdf7..538a7ce25e971b36485133751f87a64c9c689401 100644
--- a/config/examples/Sanguinololu/Configuration_adv.h
+++ b/config/examples/Sanguinololu/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/TheBorg/Configuration.h b/config/examples/TheBorg/Configuration.h
index 7cca46a694a2889162c2c5fee9874e164b76a143..fd84149ed8a35c9fee869debc8855013ec5c0ed8 100644
--- a/config/examples/TheBorg/Configuration.h
+++ b/config/examples/TheBorg/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/TheBorg/Configuration_adv.h b/config/examples/TheBorg/Configuration_adv.h
index be9897bbfe0d5b4a9251e645fc3e38037891dcbd..0fcea22a24be57a3261d21fdf031bf3c066b5a4e 100644
--- a/config/examples/TheBorg/Configuration_adv.h
+++ b/config/examples/TheBorg/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/TinyBoy2/Configuration.h b/config/examples/TinyBoy2/Configuration.h
index 4314f841316d0e09bcc078c4bf24f98e28dd05b2..0e2900b32719a280fcf4d14942d04536f24235fe 100644
--- a/config/examples/TinyBoy2/Configuration.h
+++ b/config/examples/TinyBoy2/Configuration.h
@@ -879,72 +879,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/TinyBoy2/Configuration_adv.h b/config/examples/TinyBoy2/Configuration_adv.h
index a5897f54baf37bd806c9d60b77a11a5c5d7169cf..884ed395aedc85f97766042469ccb109b5554401 100644
--- a/config/examples/TinyBoy2/Configuration_adv.h
+++ b/config/examples/TinyBoy2/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Tronxy/X1/Configuration.h b/config/examples/Tronxy/X1/Configuration.h
index 5c1bd2848bd23804aaf6ea725178b24f3abc8932..20bda64b174242a2697120edaeeb23b47b2a3be1 100644
--- a/config/examples/Tronxy/X1/Configuration.h
+++ b/config/examples/Tronxy/X1/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Tronxy/X3A/Configuration.h b/config/examples/Tronxy/X3A/Configuration.h
index 38ba1ceec70c6b44b39010d7d98791e0252884cc..d939ade6d132a323f41a5c0a254392e6d7053b79 100644
--- a/config/examples/Tronxy/X3A/Configuration.h
+++ b/config/examples/Tronxy/X3A/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Tronxy/X3A/Configuration_adv.h b/config/examples/Tronxy/X3A/Configuration_adv.h
index f0cb8264e0dab632c95446b2e531b00b4bfd0dc2..5527d3091c774a127808f17883dd00a97c5265e2 100644
--- a/config/examples/Tronxy/X3A/Configuration_adv.h
+++ b/config/examples/Tronxy/X3A/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Tronxy/X5S-2E/Configuration.h b/config/examples/Tronxy/X5S-2E/Configuration.h
index d037e0a223dc632dda950e53f6f979a4f2269a45..b94a1810e9c7db6477f756a32c7c5e97cda15cac 100644
--- a/config/examples/Tronxy/X5S-2E/Configuration.h
+++ b/config/examples/Tronxy/X5S-2E/Configuration.h
@@ -849,72 +849,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Tronxy/X5S-2E/Configuration_adv.h b/config/examples/Tronxy/X5S-2E/Configuration_adv.h
index 5bd667b00d393ad1d89bb00806b342a1dfd1315a..c6f0cfb22a4b19207b80b80f9833ce85d7e32887 100644
--- a/config/examples/Tronxy/X5S-2E/Configuration_adv.h
+++ b/config/examples/Tronxy/X5S-2E/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Tronxy/X5S/Configuration.h b/config/examples/Tronxy/X5S/Configuration.h
index 555cc1b46667797669f569ee55abbcbb623b65e7..3c2b6fb5bfeb19d3ea682352315c84ebe2ef8659 100644
--- a/config/examples/Tronxy/X5S/Configuration.h
+++ b/config/examples/Tronxy/X5S/Configuration.h
@@ -827,72 +827,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Tronxy/XY100/Configuration.h b/config/examples/Tronxy/XY100/Configuration.h
index 21181933a6ea201c8eac78af49069e207aa33504..0cc4f8a6183d270dc0d9e7f492a13d55cbf0fe55 100644
--- a/config/examples/Tronxy/XY100/Configuration.h
+++ b/config/examples/Tronxy/XY100/Configuration.h
@@ -839,72 +839,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/UltiMachine/Archim1/Configuration.h b/config/examples/UltiMachine/Archim1/Configuration.h
index ce05be362df6dd6c3c4f45d59692133026fe8a28..2b4308954517b0e5af457f0728603f76c3c962b1 100644
--- a/config/examples/UltiMachine/Archim1/Configuration.h
+++ b/config/examples/UltiMachine/Archim1/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/UltiMachine/Archim1/Configuration_adv.h b/config/examples/UltiMachine/Archim1/Configuration_adv.h
index 67e555ef139f261ac433e684190af707cd1dc337..901a64bfca834d10b40ab64242a1aeb93cf842da 100644
--- a/config/examples/UltiMachine/Archim1/Configuration_adv.h
+++ b/config/examples/UltiMachine/Archim1/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/UltiMachine/Archim2/Configuration.h b/config/examples/UltiMachine/Archim2/Configuration.h
index ebebd94a56d78d84f0ef446f00a69cf3ff6cb3f8..557b10fa38950ce8a6b95328830a77b9a5a2b1f8 100644
--- a/config/examples/UltiMachine/Archim2/Configuration.h
+++ b/config/examples/UltiMachine/Archim2/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/UltiMachine/Archim2/Configuration_adv.h b/config/examples/UltiMachine/Archim2/Configuration_adv.h
index ae2350c9bf1eb68acf0a924c24aa1790abfb684d..2db889e01fc2fc7e3c9a6f4ca6add034803aeebc 100644
--- a/config/examples/UltiMachine/Archim2/Configuration_adv.h
+++ b/config/examples/UltiMachine/Archim2/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/VORONDesign/Configuration.h b/config/examples/VORONDesign/Configuration.h
index ba2668dfb11a67692e05dc679b8b6a9768c36213..3c4c02821bf2bc60353b259c3191884ca135ee40 100644
--- a/config/examples/VORONDesign/Configuration.h
+++ b/config/examples/VORONDesign/Configuration.h
@@ -837,72 +837,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/VORONDesign/Configuration_adv.h b/config/examples/VORONDesign/Configuration_adv.h
index 929f7d3a202f16b1dd8d24b7af07ff62fb45443f..27276c31a86b3ff527f62491628011f8ff3f7dc6 100644
--- a/config/examples/VORONDesign/Configuration_adv.h
+++ b/config/examples/VORONDesign/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Velleman/K8200/Configuration.h b/config/examples/Velleman/K8200/Configuration.h
index 4de39be6cc28773451c78cbcb94eb3df6d60350a..9db1ccd9c9455e4cff0b07038b2a041a39ee2ea3 100644
--- a/config/examples/Velleman/K8200/Configuration.h
+++ b/config/examples/Velleman/K8200/Configuration.h
@@ -857,72 +857,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Velleman/K8200/Configuration_adv.h b/config/examples/Velleman/K8200/Configuration_adv.h
index 4f1ead851e52f15086b6f8ffe4e3bd5d133c82aa..62c0f9208ac0a82f92146b74b88f67b62053d5c9 100644
--- a/config/examples/Velleman/K8200/Configuration_adv.h
+++ b/config/examples/Velleman/K8200/Configuration_adv.h
@@ -537,6 +537,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Velleman/K8400/Configuration.h b/config/examples/Velleman/K8400/Configuration.h
index f5a5a0a277eff348739452b270ac6b42c62eeb8b..ae95f54c2e87b580d6542174b9b8c29dd7aa4ace 100644
--- a/config/examples/Velleman/K8400/Configuration.h
+++ b/config/examples/Velleman/K8400/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Velleman/K8400/Configuration_adv.h b/config/examples/Velleman/K8400/Configuration_adv.h
index 9806fd8d28730b5bd2e0f2760b464400c0c2a217..06c956c67e8a6afa20f0c38171bd244b02c193bc 100644
--- a/config/examples/Velleman/K8400/Configuration_adv.h
+++ b/config/examples/Velleman/K8400/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration.h b/config/examples/Velleman/K8400/Dual-head/Configuration.h
index 5eaa175fb9df5d820d5bf5453b886fe10cdc065c..f75f207c7237d870540394e699391f4b48728c76 100644
--- a/config/examples/Velleman/K8400/Dual-head/Configuration.h
+++ b/config/examples/Velleman/K8400/Dual-head/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/WASP/PowerWASP/Configuration.h b/config/examples/WASP/PowerWASP/Configuration.h
index 00430b6f7a0a9dc6f3146248412deb07a8a3c340..df74b08b7f4f29fac3e38fb0be8eb7e44d7d942c 100644
--- a/config/examples/WASP/PowerWASP/Configuration.h
+++ b/config/examples/WASP/PowerWASP/Configuration.h
@@ -847,72 +847,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/WASP/PowerWASP/Configuration_adv.h b/config/examples/WASP/PowerWASP/Configuration_adv.h
index 6479b6c715a2c73df3111577cb3c48331ce2c36e..0ade33dba4ab3906afad482136585d6aa81fc6fa 100644
--- a/config/examples/WASP/PowerWASP/Configuration_adv.h
+++ b/config/examples/WASP/PowerWASP/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/Wanhao/Duplicator 6/Configuration.h b/config/examples/Wanhao/Duplicator 6/Configuration.h
index 91542ab896b544aa0a63b12a60ddeaff59755534..fc8b47d54a85c64dedbb056f27f4312b9746f791 100644
--- a/config/examples/Wanhao/Duplicator 6/Configuration.h
+++ b/config/examples/Wanhao/Duplicator 6/Configuration.h
@@ -838,72 +838,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
index 0348e7eabf560c56a3dea37c613ed6e44a912feb..c098a182e1e62f7f767fbfb88fc9e8db363eef53 100644
--- a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
+++ b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/adafruit/ST7565/Configuration.h b/config/examples/adafruit/ST7565/Configuration.h
index cc5538cfaddb5f2817c346feeee2018c8a880122..d054246de43d8ba34ab04753077f9f6fa66a9bc3 100644
--- a/config/examples/adafruit/ST7565/Configuration.h
+++ b/config/examples/adafruit/ST7565/Configuration.h
@@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/delta/Anycubic/Kossel/Configuration.h b/config/examples/delta/Anycubic/Kossel/Configuration.h
index c37f7b3f86599dcbcbf93f20a3f16b92fb214479..b9318f52980a89f768a9ed25c245fc81e4309aa3 100644
--- a/config/examples/delta/Anycubic/Kossel/Configuration.h
+++ b/config/examples/delta/Anycubic/Kossel/Configuration.h
@@ -964,72 +964,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h
index 8a5631d6167131268c93978a13ba27c563d4c57b..b2ab1c9e8b88b6a621cba6ef179cbe78688d6c3c 100644
--- a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h
+++ b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
index efb572b617bd35a739a66b8d9824c9d03d486a2e..6d21f025b893bfad1c776d0ae67962a8f80d8720 100644
--- a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
+++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
@@ -910,72 +910,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
index e5930d4d097c023ca88965368d8a5538c6bff759..0a1f394ee8a60e469bb78440b2cb93e579af476f 100644
--- a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
+++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/delta/FLSUN/kossel/Configuration.h b/config/examples/delta/FLSUN/kossel/Configuration.h
index ff0f9fedcf0e80384da4f7852f8471997972a2d0..0d648a1e996d8e4d08f96722e0b9fb98be5205eb 100644
--- a/config/examples/delta/FLSUN/kossel/Configuration.h
+++ b/config/examples/delta/FLSUN/kossel/Configuration.h
@@ -910,72 +910,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/config/examples/delta/FLSUN/kossel/Configuration_adv.h
index e5930d4d097c023ca88965368d8a5538c6bff759..0a1f394ee8a60e469bb78440b2cb93e579af476f 100644
--- a/config/examples/delta/FLSUN/kossel/Configuration_adv.h
+++ b/config/examples/delta/FLSUN/kossel/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/config/examples/delta/FLSUN/kossel_mini/Configuration.h
index e0f14e49706b3ca909cf7c0abf3381e6c91f00b8..ecd3f24c6eab251b45386d8e2926c584bcad6ed1 100644
--- a/config/examples/delta/FLSUN/kossel_mini/Configuration.h
+++ b/config/examples/delta/FLSUN/kossel_mini/Configuration.h
@@ -910,72 +910,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
index 51366ab4573f6ddd9921e0cf1dfea90a9fd8a7cb..c16cccf51aeeb3be2e6a51865e3826d6893272ca 100644
--- a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
+++ b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration.h b/config/examples/delta/Geeetech/Rostock 301/Configuration.h
index f33b75943881ea07e1bd9ab29ef377307d6c7034..37d21e6bf4181b357f9cc4eb730e637d5c08e190 100644
--- a/config/examples/delta/Geeetech/Rostock 301/Configuration.h
+++ b/config/examples/delta/Geeetech/Rostock 301/Configuration.h
@@ -900,72 +900,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h
index 51366ab4573f6ddd9921e0cf1dfea90a9fd8a7cb..c16cccf51aeeb3be2e6a51865e3826d6893272ca 100644
--- a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h
+++ b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/delta/Hatchbox_Alpha/Configuration.h b/config/examples/delta/Hatchbox_Alpha/Configuration.h
index 9d1ca4b879ac042945db5be36a5c035fdede0aa4..f942c3cdc8ab785b2e923c680a2edb924fb5f219 100644
--- a/config/examples/delta/Hatchbox_Alpha/Configuration.h
+++ b/config/examples/delta/Hatchbox_Alpha/Configuration.h
@@ -915,72 +915,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/delta/MKS/SBASE/Configuration.h b/config/examples/delta/MKS/SBASE/Configuration.h
index 0a1e637cfdab37bfff7ec06e49f2c56161cf4c45..f1a065de3be5e5fce518aa9b29693c934f99fd9d 100644
--- a/config/examples/delta/MKS/SBASE/Configuration.h
+++ b/config/examples/delta/MKS/SBASE/Configuration.h
@@ -900,72 +900,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/delta/MKS/SBASE/Configuration_adv.h b/config/examples/delta/MKS/SBASE/Configuration_adv.h
index 9a79048ca78eac8ba9da5e384386f0ef851328db..2e7c675ad5ebf1e15c885ee33a856fc0600c9d48 100644
--- a/config/examples/delta/MKS/SBASE/Configuration_adv.h
+++ b/config/examples/delta/MKS/SBASE/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/delta/Tevo Little Monster/Configuration.h b/config/examples/delta/Tevo Little Monster/Configuration.h
index ed9c4794d33d5db82c27e0834f2866ba0978ab30..5b8f22894440da4d11ec1bba6f799ba326f6a456 100644
--- a/config/examples/delta/Tevo Little Monster/Configuration.h
+++ b/config/examples/delta/Tevo Little Monster/Configuration.h
@@ -904,9 +904,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
#define BLTOUCH
-#if ENABLED(BLTOUCH)
- #define BLTOUCH_DELAY 500 // (ms) Enable and increase if needed
-#endif
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/delta/Tevo Little Monster/Configuration_adv.h b/config/examples/delta/Tevo Little Monster/Configuration_adv.h
index a64cb6d9df2fa3cadb6dbfcdc6f41d20974b7e59..301027944d76821e862945f0c8bf19af31b1f8ff 100644
--- a/config/examples/delta/Tevo Little Monster/Configuration_adv.h
+++ b/config/examples/delta/Tevo Little Monster/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ #define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/delta/generic/Configuration.h b/config/examples/delta/generic/Configuration.h
index 7d8ac8b7dc9c1d15994876cdbb36e1c8ac82104f..b8151d4c294185d823faf008ac2bf068fd89fd5b 100644
--- a/config/examples/delta/generic/Configuration.h
+++ b/config/examples/delta/generic/Configuration.h
@@ -900,72 +900,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/delta/generic/Configuration_adv.h b/config/examples/delta/generic/Configuration_adv.h
index 51366ab4573f6ddd9921e0cf1dfea90a9fd8a7cb..c16cccf51aeeb3be2e6a51865e3826d6893272ca 100644
--- a/config/examples/delta/generic/Configuration_adv.h
+++ b/config/examples/delta/generic/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/delta/kossel_mini/Configuration.h b/config/examples/delta/kossel_mini/Configuration.h
index a0bd3f4837a1c73de76df65b44b0df10260c2964..075eecd97327ebb9670161fd066bc19013b7b6b7 100644
--- a/config/examples/delta/kossel_mini/Configuration.h
+++ b/config/examples/delta/kossel_mini/Configuration.h
@@ -900,72 +900,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/delta/kossel_mini/Configuration_adv.h b/config/examples/delta/kossel_mini/Configuration_adv.h
index 7cd0f34eb2e7cb486543c7459e6da2ef477137a1..8e0aa391461d12883a0a5d12907bc69f4c1e263a 100644
--- a/config/examples/delta/kossel_mini/Configuration_adv.h
+++ b/config/examples/delta/kossel_mini/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/delta/kossel_pro/Configuration.h b/config/examples/delta/kossel_pro/Configuration.h
index 9ff612e3d175e68d0783be292634cf6a29381602..8490c2fd08caa9039eb531b7747dc7fac93696a7 100644
--- a/config/examples/delta/kossel_pro/Configuration.h
+++ b/config/examples/delta/kossel_pro/Configuration.h
@@ -893,72 +893,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/delta/kossel_xl/Configuration.h b/config/examples/delta/kossel_xl/Configuration.h
index 98bbb578dbc74d7526018061d92fa6a02be31642..ce240d02b02f04b79e3070abd23a85447f12e1e2 100644
--- a/config/examples/delta/kossel_xl/Configuration.h
+++ b/config/examples/delta/kossel_xl/Configuration.h
@@ -903,72 +903,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/delta/kossel_xl/Configuration_adv.h b/config/examples/delta/kossel_xl/Configuration_adv.h
index 9fc842d529289c985778cf83120d8bfc5d2a053c..cf1622c8eab12baa66d5a1fa806d237293259f1f 100644
--- a/config/examples/delta/kossel_xl/Configuration_adv.h
+++ b/config/examples/delta/kossel_xl/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/gCreate/gMax1.5+/Configuration.h b/config/examples/gCreate/gMax1.5+/Configuration.h
index 4d8243abb9e117a5b05a16d4d8bf2d2f436514b6..a6fc8700f8f591f09bdf784fa68ef139472ce4a0 100644
--- a/config/examples/gCreate/gMax1.5+/Configuration.h
+++ b/config/examples/gCreate/gMax1.5+/Configuration.h
@@ -841,9 +841,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
#define BLTOUCH
-#if ENABLED(BLTOUCH)
- #define BLTOUCH_DELAY 500 // (ms) Enable and increase if needed
-#endif
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/config/examples/gCreate/gMax1.5+/Configuration_adv.h
index 8ecf7f8838f387498d9b1643e8d118d780c82f2b..f17c1c83913d1b55227e5a20a6b57df3a5b45f2a 100644
--- a/config/examples/gCreate/gMax1.5+/Configuration_adv.h
+++ b/config/examples/gCreate/gMax1.5+/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/makibox/Configuration.h b/config/examples/makibox/Configuration.h
index 3024b8a44a5310f285010a92adf7a95fce774186..4de7ede07b6ba4e539dc8d69ce0df687af825fda 100644
--- a/config/examples/makibox/Configuration.h
+++ b/config/examples/makibox/Configuration.h
@@ -831,72 +831,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/makibox/Configuration_adv.h b/config/examples/makibox/Configuration_adv.h
index b5436955163950e213aea4905254e1ee89b6f7b6..95f2b7b6706c3872215c9b591c65b5e66b7beb19 100644
--- a/config/examples/makibox/Configuration_adv.h
+++ b/config/examples/makibox/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/tvrrug/Round2/Configuration.h b/config/examples/tvrrug/Round2/Configuration.h
index 091376d9475c4b2b59a38f51931b53fd100f1875..369bc51d4526b408de5004b2a973598da3ba70b6 100644
--- a/config/examples/tvrrug/Round2/Configuration.h
+++ b/config/examples/tvrrug/Round2/Configuration.h
@@ -823,72 +823,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/tvrrug/Round2/Configuration_adv.h b/config/examples/tvrrug/Round2/Configuration_adv.h
index 8ef697e220ce643255ec117c9651da7cf35e9c08..c0178785e7ec4a81dc4938b1760ab820bcfe542c 100644
--- a/config/examples/tvrrug/Round2/Configuration_adv.h
+++ b/config/examples/tvrrug/Round2/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.
diff --git a/config/examples/wt150/Configuration.h b/config/examples/wt150/Configuration.h
index b9eb51590816ac52c62ea18d94cc1fce3b539825..f94d34856b1ca07897d2b3858974e6e59803e285 100644
--- a/config/examples/wt150/Configuration.h
+++ b/config/examples/wt150/Configuration.h
@@ -833,72 +833,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- /**
- * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
- * Do not activate settings that the probe might not understand. Clones might misunderstand
- * advanced commands.
- *
- * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
- * check the wiring of the BROWN, RED and ORANGE wires.
- *
- * Note: If the trigger signal of your probe is not being recognized, it has been very often
- * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
- * like they would be with a real switch. So please check the wiring first.
- *
- * Settings for all BLTouch and clone probes:
- */
-
- // Safety: The probe needs time to recognize the command.
- // Minimum command delay (ms). Enable and increase if needed.
- //#define BLTOUCH_DELAY 500
-
- /**
- * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
- */
-
- // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
- // in special cases, like noisy or filtered input configurations.
- //#define BLTOUCH_FORCE_SW_MODE
-
- /**
- * Settings for BLTouch Smart 3.0 and 3.1
- * Summary:
- * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
- * - High-Speed mode
- * - Disable LCD voltage options
- */
-
- /**
- * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
- * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
- * If disabled, OD mode is the hard-coded default on 3.0
- * On startup, Marlin will compare its eeprom to this vale. If the selected mode
- * differs, a mode set eeprom write will be completed at initialization.
- * Use the option below to force an eeprom write to a V3.1 probe regardless.
- */
- //#define BLTOUCH_SET_5V_MODE
-
- /**
- * Safety: Activate if connecting a probe with an unknown voltage mode.
- * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
- * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
- * To preserve the life of the probe, use this once then turn it off and re-flash.
- */
- //#define BLTOUCH_FORCE_MODE_SET
-
- /**
- * Use "HIGH SPEED" mode for probing.
- * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
- * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
- * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
- */
- //#define BLTOUCH_HS_MODE
-
- // Safety: Enable voltage mode settings in the LCD menu.
- //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
diff --git a/config/examples/wt150/Configuration_adv.h b/config/examples/wt150/Configuration_adv.h
index c6b1912d7b4a88fb59f7164fb683064aeebd23d8..396e9424d4af3cc8e5e001b0b8839ce9844da7b8 100644
--- a/config/examples/wt150/Configuration_adv.h
+++ b/config/examples/wt150/Configuration_adv.h
@@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
+#if ENABLED(BLTOUCH)
+ /**
+ * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+ * Do not activate settings that the probe might not understand. Clones might misunderstand
+ * advanced commands.
+ *
+ * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+ * check the wiring of the BROWN, RED and ORANGE wires.
+ *
+ * Note: If the trigger signal of your probe is not being recognized, it has been very often
+ * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+ * like they would be with a real switch. So please check the wiring first.
+ *
+ * Settings for all BLTouch and clone probes:
+ */
+
+ // Safety: The probe needs time to recognize the command.
+ // Minimum command delay (ms). Enable and increase if needed.
+ //#define BLTOUCH_DELAY 500
+
+ /**
+ * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+ */
+
+ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+ // in special cases, like noisy or filtered input configurations.
+ //#define BLTOUCH_FORCE_SW_MODE
+
+ /**
+ * Settings for BLTouch Smart 3.0 and 3.1
+ * Summary:
+ * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+ * - High-Speed mode
+ * - Disable LCD voltage options
+ */
+
+ /**
+ * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+ * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+ * If disabled, OD mode is the hard-coded default on 3.0
+ * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+ * differs, a mode set eeprom write will be completed at initialization.
+ * Use the option below to force an eeprom write to a V3.1 probe regardless.
+ */
+ //#define BLTOUCH_SET_5V_MODE
+
+ /**
+ * Safety: Activate if connecting a probe with an unknown voltage mode.
+ * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+ * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+ * To preserve the life of the probe, use this once then turn it off and re-flash.
+ */
+ //#define BLTOUCH_FORCE_MODE_SET
+
+ /**
+ * Use "HIGH SPEED" mode for probing.
+ * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+ * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+ * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+ */
+ //#define BLTOUCH_HS_MODE
+
+ // Safety: Enable voltage mode settings in the LCD menu.
+ //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.