diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index a338ff85e6825980c31a45baf95a022c5fba9c30..3004cf12581c7b980da65d5639f00a9ecf6f0d43 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -950,6 +953,13 @@
#define UBL_PROBE_PT_3_Y 20
//#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1690,18 +1700,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1723,7 +1721,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/default/Configuration.h b/Marlin/src/config/default/Configuration.h
index a338ff85e6825980c31a45baf95a022c5fba9c30..3004cf12581c7b980da65d5639f00a9ecf6f0d43 100644
--- a/Marlin/src/config/default/Configuration.h
+++ b/Marlin/src/config/default/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -950,6 +953,13 @@
#define UBL_PROBE_PT_3_Y 20
//#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1690,18 +1700,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1723,7 +1721,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h
index 920f17ceac0dc905b9542038b5396ab2c9905beb..11aacd5246e048b20c92af9438b8216b26d305e5 100644
--- a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h
+++ b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -970,6 +973,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1710,18 +1720,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1743,7 +1741,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h b/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h
index 51ca09d5f41ad6e9d700fa9f233e6e1a2554f6b2..768f452eb87964525e515fba42122a9d5e8229e4 100644
--- a/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h
+++ b/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -950,6 +953,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1690,18 +1700,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1723,7 +1721,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/Anet/A6/Configuration.h b/Marlin/src/config/examples/Anet/A6/Configuration.h
index b2a8b57ea98b5fc7f76553d5bfff55c6e807e486..2de8adf1b89aca1a89ede73d555f31049ec3bf0b 100644
--- a/Marlin/src/config/examples/Anet/A6/Configuration.h
+++ b/Marlin/src/config/examples/Anet/A6/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -1093,6 +1096,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1849,18 +1859,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1882,7 +1880,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/Anet/A8/Configuration.h b/Marlin/src/config/examples/Anet/A8/Configuration.h
index ca66ccebc999e37f6ddb4606db184a1711781bbe..2684bb9b35b5764d11d1199e71d73853aac5bc77 100644
--- a/Marlin/src/config/examples/Anet/A8/Configuration.h
+++ b/Marlin/src/config/examples/Anet/A8/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -956,6 +959,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1698,18 +1708,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1731,7 +1729,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h b/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h
index ef515150867e64a1580fd80f527f8fb82980cbf3..4017d2688553302b3bb4e11823ec8c210f590c62 100644
--- a/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h
+++ b/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 2
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -950,6 +953,13 @@
#define UBL_PROBE_PT_3_Y 20
//#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1685,18 +1695,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1718,7 +1716,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/BQ/Hephestos/Configuration.h b/Marlin/src/config/examples/BQ/Hephestos/Configuration.h
index 98b6bd561626b884ef79d01e819c8dc1cf6e655d..24b7d63d8c883fcd7a909df1172d0cb561354135 100644
--- a/Marlin/src/config/examples/BQ/Hephestos/Configuration.h
+++ b/Marlin/src/config/examples/BQ/Hephestos/Configuration.h
@@ -139,6 +139,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -941,6 +944,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1681,18 +1691,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1714,7 +1712,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h
index 2a4df49f324f73791deba9fea9ebe8c0363706d8..901c3830478f3bf62220d02d4d6fa8ea390d830d 100644
--- a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h
+++ b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h
@@ -135,6 +135,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -951,6 +954,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1691,18 +1701,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1724,7 +1722,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 2.00 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/BQ/WITBOX/Configuration.h b/Marlin/src/config/examples/BQ/WITBOX/Configuration.h
index 10914bf1f1365a69c08d5e2fe748a821d9984e93..834089c525fbcc56162782b14f1b9800b64cff23 100644
--- a/Marlin/src/config/examples/BQ/WITBOX/Configuration.h
+++ b/Marlin/src/config/examples/BQ/WITBOX/Configuration.h
@@ -139,6 +139,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -941,6 +944,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1681,18 +1691,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1714,7 +1712,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/Cartesio/Configuration.h b/Marlin/src/config/examples/Cartesio/Configuration.h
index 6e98801dd52eee7009763f3f24027c64b9c4174a..e1934c9d909e4fa9e59054672026bb58ee43f87f 100644
--- a/Marlin/src/config/examples/Cartesio/Configuration.h
+++ b/Marlin/src/config/examples/Cartesio/Configuration.h
@@ -137,6 +137,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 3
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -949,6 +952,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1689,18 +1699,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1722,7 +1720,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/Creality/CR-10/Configuration.h b/Marlin/src/config/examples/Creality/CR-10/Configuration.h
index ba15c570bcab94fa6eb12059d6571c4aea3e68e1..cb430c48a1880552673d77e34b0a32a157855437 100755
--- a/Marlin/src/config/examples/Creality/CR-10/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-10/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -960,6 +963,13 @@
#define UBL_PROBE_PT_3_Y 20
//#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1700,18 +1710,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1736,7 +1734,7 @@
//#define DEFAULT_STDDEV_FILAMENT_DIA 0.02 // Typical advertised for higher quality filament
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT (DEFAULT_NOMINAL_FILAMENT_DIA+4*DEFAULT_STDDEV_FILAMENT_DIA) // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/Felix/Configuration.h b/Marlin/src/config/examples/Felix/Configuration.h
index 77ecd28a987002b2b2656b589ac18668d0dc5a09..02c01555529769b3c4bca880af16e20d6423082a 100644
--- a/Marlin/src/config/examples/Felix/Configuration.h
+++ b/Marlin/src/config/examples/Felix/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -932,6 +935,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1672,18 +1682,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1705,7 +1703,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/Felix/DUAL/Configuration.h b/Marlin/src/config/examples/Felix/DUAL/Configuration.h
index 147597c2acb513c0dc26ea02f90272d102a2040d..b79f659df47b182dde886b383b3d915134d358a1 100644
--- a/Marlin/src/config/examples/Felix/DUAL/Configuration.h
+++ b/Marlin/src/config/examples/Felix/DUAL/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 2
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -932,6 +935,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1672,18 +1682,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1705,7 +1703,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h
index 4a8551b982275a86ce4429409dc41de108e9279a..28a9a54036d7d7c3772be8be64872cff154d5f3e 100644
--- a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h
+++ b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h
@@ -137,6 +137,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -947,6 +950,13 @@
#define UBL_PROBE_PT_3_Y 25
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1687,18 +1697,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1720,7 +1718,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h b/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h
index 7a8d16d8b78d52d2f4097bb493571116f3dddf2b..263df4a75140f63d078ad449fc02079b66f5b6a5 100644
--- a/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h
+++ b/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -965,6 +968,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1705,18 +1715,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1738,7 +1736,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
index 21b6b0f31c9f0212fbeefecf5d8f51311c08b192..636e86006680f2448bbed725bbe651f2fbb9774b 100644
--- a/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
+++ b/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -950,6 +953,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1690,18 +1700,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1723,7 +1721,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h b/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h
index 17ca4a43ecfea86723c3918bd45b18b748b8b249..f69deff547d9878a5adb93fadc38ee7f7278ff23 100644
--- a/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h
+++ b/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -954,6 +957,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1694,18 +1704,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1727,7 +1725,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/Malyan/M150/Configuration.h b/Marlin/src/config/examples/Malyan/M150/Configuration.h
index bd667914c140ba31636c22978eac9b7a7411f863..a5482e310630791c675e0a01805f354b1a65dbc2 100644
--- a/Marlin/src/config/examples/Malyan/M150/Configuration.h
+++ b/Marlin/src/config/examples/Malyan/M150/Configuration.h
@@ -141,6 +141,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -978,6 +981,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1718,18 +1728,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1751,7 +1749,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h b/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h
index 31d99aa7207f1376e7c7e8ffb4fa2c914586b3df..581d1d4f7789ad71ae9698d849b3f9bff35eb4f7 100644
--- a/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h
+++ b/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -954,6 +957,13 @@
#define UBL_PROBE_PT_3_Y 20
//#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1694,18 +1704,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1727,7 +1725,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h
index 30c8ccd8eab080fbbb154552c99a1342aac9f14e..9963fc7bd3a41b07dd694127dd5ff2d17c42fdfe 100644
--- a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h
+++ b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -954,6 +957,13 @@
#define UBL_PROBE_PT_3_Y 20
//#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1694,18 +1704,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1727,7 +1725,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/Mks/Sbase/Configuration.h b/Marlin/src/config/examples/Mks/Sbase/Configuration.h
index 9f6b458c1577642c1876b4befb1e2e111175f650..0b30b26226e13db82490702e6d0b7e93441b0d95 100644
--- a/Marlin/src/config/examples/Mks/Sbase/Configuration.h
+++ b/Marlin/src/config/examples/Mks/Sbase/Configuration.h
@@ -137,6 +137,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -951,6 +954,13 @@
#define UBL_PROBE_PT_3_Y 20
//#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1665,18 +1675,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1698,7 +1696,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h b/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h
index 921a5df60f5c09507476926188ca11bfd89802d8..08299d6d8bd57ece7d46821b3dd3e3aa56713844 100644
--- a/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h
+++ b/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -950,6 +953,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1690,18 +1700,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1723,7 +1721,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/RigidBot/Configuration.h b/Marlin/src/config/examples/RigidBot/Configuration.h
index b296eb2d942ffdbd65b0191987d217271c15adf1..56197e605bedd5b3480ef53921d1e63b166d1b66 100644
--- a/Marlin/src/config/examples/RigidBot/Configuration.h
+++ b/Marlin/src/config/examples/RigidBot/Configuration.h
@@ -139,6 +139,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1 // Single extruder. Set to 2 for dual extruders
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -948,6 +951,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1690,18 +1700,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1723,7 +1721,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/SCARA/Configuration.h b/Marlin/src/config/examples/SCARA/Configuration.h
index 26afa9f40785a6b122370da6312c72e6008212c9..5ae2816ac838551bac6b33f0bee6dfdbe02fb954 100644
--- a/Marlin/src/config/examples/SCARA/Configuration.h
+++ b/Marlin/src/config/examples/SCARA/Configuration.h
@@ -166,6 +166,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -962,6 +965,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1702,18 +1712,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1735,7 +1733,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/STM32F10/Configuration.h b/Marlin/src/config/examples/STM32F10/Configuration.h
index 7c3b6bf2202a4645e25e756248c54e6a428810de..29e02f91b0299c7189d9629bae7e34461bfe95ca 100644
--- a/Marlin/src/config/examples/STM32F10/Configuration.h
+++ b/Marlin/src/config/examples/STM32F10/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -953,6 +956,13 @@
#define UBL_PROBE_PT_3_Y 20
//#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1693,18 +1703,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1726,7 +1724,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/Sanguinololu/Configuration.h b/Marlin/src/config/examples/Sanguinololu/Configuration.h
index 0df8eedec9688a05c3518a7df37f8ebb6446075c..0e514fc325873aa56dcc59e85a2c0797f9c58d5a 100644
--- a/Marlin/src/config/examples/Sanguinololu/Configuration.h
+++ b/Marlin/src/config/examples/Sanguinololu/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -981,6 +984,13 @@
#define UBL_PROBE_PT_3_Y 20
//#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1721,18 +1731,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1754,7 +1752,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/TinyBoy2/Configuration.h b/Marlin/src/config/examples/TinyBoy2/Configuration.h
index 8732e1caefcd18f484818078c2edbea073a56200..40a88d2518b891de4c23b9fcbec45a6f40f8be89 100644
--- a/Marlin/src/config/examples/TinyBoy2/Configuration.h
+++ b/Marlin/src/config/examples/TinyBoy2/Configuration.h
@@ -158,6 +158,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -1006,6 +1009,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1746,18 +1756,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1779,7 +1777,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h
index 882a061f9eadc6cf11abcc796971718f45f0719f..6f2cff13a0625cc5ce1c148e5ec73ceb253a81ef 100644
--- a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h
+++ b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -950,6 +953,13 @@
#define UBL_PROBE_PT_3_Y 20
//#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1691,18 +1701,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1724,7 +1722,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/Velleman/K8200/Configuration.h b/Marlin/src/config/examples/Velleman/K8200/Configuration.h
index 98b551ba39b35faa4a24e6dbceb3f2609494e59a..07ab2e2a5f5d004dfe4dc0cae1c114f09e9b9672 100644
--- a/Marlin/src/config/examples/Velleman/K8200/Configuration.h
+++ b/Marlin/src/config/examples/Velleman/K8200/Configuration.h
@@ -156,6 +156,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -980,6 +983,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1725,18 +1735,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1758,7 +1756,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/Velleman/K8400/Configuration.h b/Marlin/src/config/examples/Velleman/K8400/Configuration.h
index 76a99fcdc71f73358db595395b165d778e1a7beb..84e5be633551ffc892cb9cc37017e15ee2f09f28 100644
--- a/Marlin/src/config/examples/Velleman/K8400/Configuration.h
+++ b/Marlin/src/config/examples/Velleman/K8400/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -950,6 +953,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1690,18 +1700,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1723,7 +1721,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h b/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h
index 35da91713268dce1d6eb05fd24cc704a1cbce022..200526eaa9d2e982fb96b8eb78a53dd190cff12c 100644
--- a/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h
+++ b/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 2
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -950,6 +953,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1690,18 +1700,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1723,7 +1721,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/adafruit/ST7565/Configuration.h b/Marlin/src/config/examples/adafruit/ST7565/Configuration.h
index b0af4027afa4465e8cc23cf7d8796a590d2a023b..bfbf9bb3e8059139865aae4d8c9db4314d77157a 100644
--- a/Marlin/src/config/examples/adafruit/ST7565/Configuration.h
+++ b/Marlin/src/config/examples/adafruit/ST7565/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -950,6 +953,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1690,18 +1700,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1723,7 +1721,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
index cc63d79ac9a9b46f62a5d5fdaadc79bef4d02893..e167dcefa14a7db1f50ed1046eeed740564413f4 100644
--- a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
+++ b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -1084,6 +1087,13 @@
#define UBL_PROBE_PT_3_Y _PY(DELTA_PROBEABLE_RADIUS, 240)
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1824,18 +1834,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1857,7 +1855,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 1.95 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h
index 8a26868c211b991d34a050e127ee3f1578701695..7f32b514c70d18dcae19b00249741419e39bb95a 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -1078,6 +1081,13 @@
#define UBL_PROBE_PT_3_Y _PY(DELTA_PROBEABLE_RADIUS, 240)
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1817,18 +1827,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1850,7 +1848,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/delta/generic/Configuration.h b/Marlin/src/config/examples/delta/generic/Configuration.h
index 2bbcf10470b952a0e38fd8d73b41e9e5abf35615..de63e91acfc08507c7697b49333c514c48d85c72 100644
--- a/Marlin/src/config/examples/delta/generic/Configuration.h
+++ b/Marlin/src/config/examples/delta/generic/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -1073,6 +1076,13 @@
#define UBL_PROBE_PT_3_Y _PY(DELTA_PROBEABLE_RADIUS, 240)
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1812,18 +1822,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1845,7 +1843,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h
index 1de41f8a2c2efda6c8ec9ccde724851d9be38088..62007f2b90a2a02d0185764d49a83039f20e612c 100644
--- a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -1076,6 +1079,13 @@
#define UBL_PROBE_PT_3_Y _PY(DELTA_PROBEABLE_RADIUS, 240)
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1815,18 +1825,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1848,7 +1846,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h
index a61e16de3d2c6ca8e87db2ff144481f3ae8ac3b9..bce2cc2e75e7b831b2e86766758f3d71e8105a6d 100644
--- a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h
@@ -140,6 +140,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -1076,6 +1079,13 @@
#define UBL_PROBE_PT_3_Y _PY(DELTA_PROBEABLE_RADIUS, 240)
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1815,18 +1825,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1848,7 +1846,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h
index 3d992a29916e320da1acee7a66be2677942d4d98..15ac367b45ba0db7fb2fb1d7033b06a9f585c56b 100644
--- a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -1085,6 +1088,13 @@
#define UBL_PROBE_PT_3_Y _PY(DELTA_PROBEABLE_RADIUS, 240)
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1824,18 +1834,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1857,7 +1855,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h
index 0518c9ecc1e43a2c4d5054e2139360813f110da4..52d2b40f1222fd2b79857fd92ea467deb4d7043a 100644
--- a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h
+++ b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h
@@ -141,6 +141,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -964,6 +967,13 @@
#define UBL_PROBE_PT_3_Y 211
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1704,18 +1714,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .5 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .35 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1737,7 +1735,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/makibox/Configuration.h b/Marlin/src/config/examples/makibox/Configuration.h
index 573c49175e9bb68a108564c89e7d5c45a41b8289..0a03d94753ef5e6612ffba8a6618f8e1a74aedaa 100644
--- a/Marlin/src/config/examples/makibox/Configuration.h
+++ b/Marlin/src/config/examples/makibox/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -953,6 +956,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1693,18 +1703,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1726,7 +1724,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/tvrrug/Round2/Configuration.h b/Marlin/src/config/examples/tvrrug/Round2/Configuration.h
index a7d2ad0f1b6b314ddf1e84a2d58ce1d36bfc845c..a269c9b4a753db2946f61049d56a3f01a9b615a2 100644
--- a/Marlin/src/config/examples/tvrrug/Round2/Configuration.h
+++ b/Marlin/src/config/examples/tvrrug/Round2/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -945,6 +948,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1685,18 +1695,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1718,7 +1716,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/config/examples/wt150/Configuration.h b/Marlin/src/config/examples/wt150/Configuration.h
index a350f433019d727400c497e85be180f421c248a4..a3f899a514a44b278fd51a6f03826b86c62d6590 100644
--- a/Marlin/src/config/examples/wt150/Configuration.h
+++ b/Marlin/src/config/examples/wt150/Configuration.h
@@ -136,6 +136,9 @@
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
@@ -955,6 +958,13 @@
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #if ENABLED(UBL_G26_MESH_VALIDATION)
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (c) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (c) Default bed temperature for the G26 Mesh Validation Tool.
+ #endif
+
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
@@ -1695,18 +1705,6 @@
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
-/**
- * Default extrusion settings
- *
- * These settings control basic extrusion from within the Marlin firmware.
- *
- */
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-#define DEFAULT_NOZZLE_SIZE .4 // (mm) Diameter of primary nozzle. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_LAYER_HEIGHT .2 // (mm) Default layer height that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_HOTEND_TEMP 205.0 // (c) Default nozzle temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-#define DEFAULT_BED_TEMP 60.0 // (c) Default bed temperature that will produce usable results by the printer. Used by G26 Mesh Validation Pattern tool.
-
/**
* Filament Width Sensor
*
@@ -1728,7 +1726,7 @@
//#define FILAMENT_WIDTH_SENSOR
#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
diff --git a/Marlin/src/feature/bedlevel/ubl/G26_Mesh_Validation_Tool.cpp b/Marlin/src/feature/bedlevel/ubl/G26_Mesh_Validation_Tool.cpp
index 4ab3f94e161205b02cb7619ea2ee36d03f14eb62..543337ac688b711357c1e24be1b80aa618174ef8 100644
--- a/Marlin/src/feature/bedlevel/ubl/G26_Mesh_Validation_Tool.cpp
+++ b/Marlin/src/feature/bedlevel/ubl/G26_Mesh_Validation_Tool.cpp
@@ -618,12 +618,12 @@ bool unified_bed_leveling::parse_G26_parameters() {
g26_extrusion_multiplier = EXTRUSION_MULTIPLIER;
g26_retraction_multiplier = RETRACTION_MULTIPLIER;
- g26_nozzle = DEFAULT_NOZZLE_SIZE;
+ g26_nozzle = MESH_TEST_NOZZLE_SIZE;
g26_filament_diameter = DEFAULT_NOMINAL_FILAMENT_DIA;
- g26_layer_height = DEFAULT_LAYER_HEIGHT;
+ g26_layer_height = MESH_TEST_LAYER_HEIGHT;
g26_prime_length = PRIME_LENGTH;
- g26_bed_temp = DEFAULT_BED_TEMP;
- g26_hotend_temp = DEFAULT_HOTEND_TEMP;
+ g26_bed_temp = MESH_TEST_BED_TEMP;
+ g26_hotend_temp = MESH_TEST_HOTEND_TEMP;
g26_prime_flag = 0;
g26_ooze_amount = parser.linearval('O', OOZE_AMOUNT);