diff --git a/Marlin/src/config/examples/Creality/CR-10S/Configuration.h b/Marlin/src/config/examples/Creality/CR-10S/Configuration.h
index d40535a31566b2c885e4ed33d0424e56df2c4bc8..8ca00396fb0325287b627ee950f67b082b9d5171 100644
--- a/Marlin/src/config/examples/Creality/CR-10S/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-10S/Configuration.h
@@ -620,7 +620,7 @@
* Use G29 repeatedly, adjusting the Z height at each point with movement commands
* or (with LCD_BED_LEVELING) the LCD controller.
*/
-//#define PROBE_MANUALLY
+#define PROBE_MANUALLY
/**
* A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
@@ -768,7 +768,7 @@
//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed
-//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case.
// Direction of endstops when homing; 1=MAX, -1=MIN
@@ -871,9 +871,9 @@
*/
//#define AUTO_BED_LEVELING_3POINT
//#define AUTO_BED_LEVELING_LINEAR
-//#define AUTO_BED_LEVELING_BILINEAR
+#define AUTO_BED_LEVELING_BILINEAR
//#define AUTO_BED_LEVELING_UBL
-#define MESH_BED_LEVELING
+//#define MESH_BED_LEVELING
/**
* Enable detailed logging of G28, G29, M48, etc.
@@ -899,10 +899,10 @@
*/
#define G26_MESH_VALIDATION // Enable G26 mesh validation
#if ENABLED(G26_MESH_VALIDATION)
- #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
- #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
- #define MESH_TEST_HOTEND_TEMP 205.0 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
- #define MESH_TEST_BED_TEMP 60.0 // (°C) Default bed temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
+ #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
+ #define MESH_TEST_HOTEND_TEMP 205.0 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
+ #define MESH_TEST_BED_TEMP 60.0 // (°C) Default bed temperature for the G26 Mesh Validation Tool.
#endif
#endif
@@ -1113,8 +1113,8 @@
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
//
-#define EEPROM_SETTINGS // Enable for M500 and M501 commands
-#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
+#define EEPROM_SETTINGS // Enable for M500 and M501 commands
+//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
//
diff --git a/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
index 4406f8ed61fd418935d12251a2d1786f06bc63bb..8187e89269b877add07169a4b0fff4d44ad08ebf 100644
--- a/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
@@ -123,7 +123,7 @@
#endif
// Show extra position information in M114
-//#define M114_DETAIL
+#define M114_DETAIL
// Show Temperature ADC value
// Enable for M105 to include ADC values read from temperature sensors.
@@ -471,7 +471,7 @@
// @section lcd
// Include a page of printer information in the LCD Main Menu
-//#define LCD_INFO_MENU
+#define LCD_INFO_MENU
// Leave out seldom-used LCD menu items to recover some Program Memory
//#define SLIM_LCD_MENUS
@@ -552,7 +552,7 @@
#define FOLDER_SORTING -1 // -1=above 0=none 1=below
#define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code.
#define SDSORT_USES_RAM true // Pre-allocate a static array for faster pre-sorting.
- #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
+ #define SDSORT_USES_STACK true // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
#define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option.
#define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
#define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting.
@@ -582,7 +582,7 @@
//#define LONG_FILENAME_HOST_SUPPORT
// Enable this option to scroll long filenames in the SD card menu
- //#define SCROLL_LONG_FILENAMES
+ #define SCROLL_LONG_FILENAMES
/**
* This option allows you to abort SD printing when any endstop is triggered.
@@ -614,7 +614,7 @@
*/
#if ENABLED(DOGLCD)
// Show SD percentage next to the progress bar
- //#define DOGM_SD_PERCENT
+ #define DOGM_SD_PERCENT
// Enable to save many cycles by drawing a hollow frame on the Info Screen
#define XYZ_HOLLOW_FRAME
@@ -736,7 +736,7 @@
//
// G2/G3 Arc Support
//
-//#define ARC_SUPPORT // Disable this feature to save ~3226 bytes
+#define ARC_SUPPORT // Disable this feature to save ~3226 bytes
#if ENABLED(ARC_SUPPORT)
#define MM_PER_ARC_SEGMENT 1 // Length of each arc segment
#define N_ARC_CORRECTION 25 // Number of intertpolated segments between corrections
@@ -821,7 +821,7 @@
// enter the serial receive buffer, so they cannot be blocked.
// Currently handles M108, M112, M410
// Does not work on boards using AT90USB (USBCON) processors!
-//#define EMERGENCY_PARSER
+#define EMERGENCY_PARSER
// Bad Serial-connections can miss a received command by sending an 'ok'
// Therefore some clients abort after 30 seconds in a timeout.
@@ -830,7 +830,7 @@
//#define NO_TIMEOUTS 1000 // Milliseconds
// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
-//#define ADVANCED_OK
+#define ADVANCED_OK
// @section extras