diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 04ed57cb732dae53e0f35167e22343c16f218f1b..27fbf0d85e9c07f301299c285f3ffcb6f306cb3e 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/Marlin/src/feature/joystick.cpp b/Marlin/src/feature/joystick.cpp
index abfd77f4380460974cbab06dadaae920aad47565..acf6c13a10afca3c0802a59ebfb396d173ca2dca 100644
--- a/Marlin/src/feature/joystick.cpp
+++ b/Marlin/src/feature/joystick.cpp
@@ -42,25 +42,40 @@ Joystick joystick;
#if HAS_JOY_ADC_X
temp_info_t Joystick::x; // = { 0 }
+ #if ENABLED(INVERT_JOY_X)
+ #define JOY_X(N) (16383 - (N))
+ #else
+ #define JOY_X(N) (N)
+ #endif
#endif
#if HAS_JOY_ADC_Y
temp_info_t Joystick::y; // = { 0 }
+ #if ENABLED(INVERT_JOY_Y)
+ #define JOY_Y(N) (16383 - (N))
+ #else
+ #define JOY_Y(N) (N)
+ #endif
#endif
#if HAS_JOY_ADC_Z
temp_info_t Joystick::z; // = { 0 }
+ #if ENABLED(INVERT_JOY_Z)
+ #define JOY_Z(N) (16383 - (N))
+ #else
+ #define JOY_Z(N) (N)
+ #endif
#endif
#if ENABLED(JOYSTICK_DEBUG)
void Joystick::report() {
SERIAL_ECHOPGM("Joystick");
#if HAS_JOY_ADC_X
- SERIAL_ECHOPAIR_P(SP_X_STR, x.raw);
+ SERIAL_ECHOPAIR_P(SP_X_STR, JOY_X(x.raw));
#endif
#if HAS_JOY_ADC_Y
- SERIAL_ECHOPAIR_P(SP_Y_STR, y.raw);
+ SERIAL_ECHOPAIR_P(SP_Y_STR, JOY_Y(y.raw));
#endif
#if HAS_JOY_ADC_Z
- SERIAL_ECHOPAIR_P(SP_Z_STR, z.raw);
+ SERIAL_ECHOPAIR_P(SP_Z_STR, JOY_Z(z.raw));
#endif
#if HAS_JOY_ADC_EN
SERIAL_ECHO_TERNARY(READ(JOY_EN_PIN), " EN=", "HIGH (dis", "LOW (en", "abled)");
@@ -91,15 +106,15 @@ Joystick joystick;
#if HAS_JOY_ADC_X
static constexpr int16_t joy_x_limits[4] = JOY_X_LIMITS;
- _normalize_joy(norm_jog.x, x.raw, joy_x_limits);
+ _normalize_joy(norm_jog.x, JOY_X(x.raw), joy_x_limits);
#endif
#if HAS_JOY_ADC_Y
static constexpr int16_t joy_y_limits[4] = JOY_Y_LIMITS;
- _normalize_joy(norm_jog.y, y.raw, joy_y_limits);
+ _normalize_joy(norm_jog.y, JOY_Y(y.raw), joy_y_limits);
#endif
#if HAS_JOY_ADC_Z
static constexpr int16_t joy_z_limits[4] = JOY_Z_LIMITS;
- _normalize_joy(norm_jog.z, z.raw, joy_z_limits);
+ _normalize_joy(norm_jog.z, JOY_Z(z.raw), joy_z_limits);
#endif
}
diff --git a/config/default/Configuration_adv.h b/config/default/Configuration_adv.h
index 04ed57cb732dae53e0f35167e22343c16f218f1b..27fbf0d85e9c07f301299c285f3ffcb6f306cb3e 100644
--- a/config/default/Configuration_adv.h
+++ b/config/default/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
index 4ccf836ec658b6e0891903db04a701eef53220dc..8f5a984500a8e5c5943c40c93068a29f786693f2 100644
--- a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
+++ b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
@@ -2774,7 +2774,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h
index 56c2f38216b79133828e7ee567e045536d339139..073618ff446639cb282bbb1a5b785b2504be101b 100644
--- a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h
+++ b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h
index 1ceeb40ac5b0d27dec2f00fd06e7c2d1cae023b0..edf4711c9ecd61ac64eb2672d17d68a90647562f 100644
--- a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h
+++ b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/config/examples/AlephObjects/TAZ4/Configuration_adv.h
index 9357c66e79eb20199cf086a5d601f467aeececa3..d5cd2b057706e9f5456748910a9f84c0605f0ac7 100644
--- a/config/examples/AlephObjects/TAZ4/Configuration_adv.h
+++ b/config/examples/AlephObjects/TAZ4/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h
index 1ea78f0ac8c07683a245360b7e539ee47dac891d..ee539807d77b241141f6f0c8c149219e5a71e82b 100644
--- a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h
+++ b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h
@@ -2765,7 +2765,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Alfawise/U20/Configuration_adv.h b/config/examples/Alfawise/U20/Configuration_adv.h
index 0b94e63ba286d842a06bcfb01b3378c9a2a5889d..492849a5b69e9f78f5d3f131b0690d9ef7627c8b 100644
--- a/config/examples/Alfawise/U20/Configuration_adv.h
+++ b/config/examples/Alfawise/U20/Configuration_adv.h
@@ -2764,7 +2764,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/AliExpress/UM2pExt/Configuration_adv.h b/config/examples/AliExpress/UM2pExt/Configuration_adv.h
index 8ed4fb665ff4ebf054583ab8983253ca5ed916c0..e7d1cc06fa99bec570ea683d82d18da03e8a11d8 100644
--- a/config/examples/AliExpress/UM2pExt/Configuration_adv.h
+++ b/config/examples/AliExpress/UM2pExt/Configuration_adv.h
@@ -2765,7 +2765,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Anet/A2/Configuration_adv.h b/config/examples/Anet/A2/Configuration_adv.h
index b451d580e7bc9b7f24b0f6a76dd56b07d9816404..f3429d756c0cd68bf070a66d0e906b8d472f0b67 100644
--- a/config/examples/Anet/A2/Configuration_adv.h
+++ b/config/examples/Anet/A2/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Anet/A2plus/Configuration_adv.h b/config/examples/Anet/A2plus/Configuration_adv.h
index b451d580e7bc9b7f24b0f6a76dd56b07d9816404..f3429d756c0cd68bf070a66d0e906b8d472f0b67 100644
--- a/config/examples/Anet/A2plus/Configuration_adv.h
+++ b/config/examples/Anet/A2plus/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Anet/A6/Configuration_adv.h b/config/examples/Anet/A6/Configuration_adv.h
index 0e162a62e020d499f3068fdfdccd7cf7c4141f43..297f9683215f8fc808cb754c331193f3d36a0a85 100644
--- a/config/examples/Anet/A6/Configuration_adv.h
+++ b/config/examples/Anet/A6/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Anet/A8/Configuration_adv.h b/config/examples/Anet/A8/Configuration_adv.h
index 571450d40030db5455d83c416c438c69bc7ab41a..3297703b1a3930fc24418b0bf840299904694c8f 100644
--- a/config/examples/Anet/A8/Configuration_adv.h
+++ b/config/examples/Anet/A8/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Anet/A8plus/Configuration_adv.h b/config/examples/Anet/A8plus/Configuration_adv.h
index 386780cffbab1235a14c325af023d870e9785fba..f765edb494396cbf5e270790cea0d9e67d538f0b 100644
--- a/config/examples/Anet/A8plus/Configuration_adv.h
+++ b/config/examples/Anet/A8plus/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Anet/E10/Configuration_adv.h b/config/examples/Anet/E10/Configuration_adv.h
index b966de0eec73b9ba56c42c7c4cce0da29cc6fd1b..5eb24aa0a0f78aecc0142a63667582c23ad4400e 100644
--- a/config/examples/Anet/E10/Configuration_adv.h
+++ b/config/examples/Anet/E10/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Anet/E16/Configuration_adv.h b/config/examples/Anet/E16/Configuration_adv.h
index 30e854a6f425b1303cdac889fcd6aacd3fe79080..6bcac3b6346a657ba36dd9e5c514d752aed9763c 100644
--- a/config/examples/Anet/E16/Configuration_adv.h
+++ b/config/examples/Anet/E16/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/AnyCubic/i3/Configuration_adv.h b/config/examples/AnyCubic/i3/Configuration_adv.h
index 3db064d92b289799dc2bfa735f19ea42d7449765..03d2d90424dc233c9d0a0782f8e742f035b3451a 100644
--- a/config/examples/AnyCubic/i3/Configuration_adv.h
+++ b/config/examples/AnyCubic/i3/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/ArmEd/Configuration_adv.h b/config/examples/ArmEd/Configuration_adv.h
index 1b9cfc0bf6a3f6a9084dfcfe4395ec89432a4673..91d36066a95ee5451e09d132e7ab7755bd4c895f 100644
--- a/config/examples/ArmEd/Configuration_adv.h
+++ b/config/examples/ArmEd/Configuration_adv.h
@@ -2767,7 +2767,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Artillery/Genius/Configuration_adv.h b/config/examples/Artillery/Genius/Configuration_adv.h
index f467710bb6272905b1fa728cd108b8f826151fb4..3b2e37e74e6acb32c895d953f8ae37f32e11658f 100755
--- a/config/examples/Artillery/Genius/Configuration_adv.h
+++ b/config/examples/Artillery/Genius/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Artillery/Sidewinder X1/Configuration_adv.h b/config/examples/Artillery/Sidewinder X1/Configuration_adv.h
index f467710bb6272905b1fa728cd108b8f826151fb4..3b2e37e74e6acb32c895d953f8ae37f32e11658f 100755
--- a/config/examples/Artillery/Sidewinder X1/Configuration_adv.h
+++ b/config/examples/Artillery/Sidewinder X1/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
index 9f114209b3bc9b00126c3402299fcbe00cb6ecc3..06c52a5e7f56d69e8546a6e77c6a38cfc83463be 100644
--- a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
+++ b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/BIBO/TouchX/default/Configuration_adv.h b/config/examples/BIBO/TouchX/default/Configuration_adv.h
index 09726de2d0a6335e8af3cc7beb862bb39f1a8202..9062f003b1d65130240bc1f0015d4a44c95ae971 100644
--- a/config/examples/BIBO/TouchX/default/Configuration_adv.h
+++ b/config/examples/BIBO/TouchX/default/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/BQ/Hephestos/Configuration_adv.h b/config/examples/BQ/Hephestos/Configuration_adv.h
index c83d4f31a87fdd7c5703d4741baccb596e75e1ff..bc8b649b30e79df3e0e5aaac915329ec8573dc51 100644
--- a/config/examples/BQ/Hephestos/Configuration_adv.h
+++ b/config/examples/BQ/Hephestos/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/BQ/Hephestos_2/Configuration_adv.h b/config/examples/BQ/Hephestos_2/Configuration_adv.h
index b4d7df86997c7a724eaf333f73bc6b6a367e8587..72524ed6c0c07aa0d4b7f87db3bd96232be204ea 100644
--- a/config/examples/BQ/Hephestos_2/Configuration_adv.h
+++ b/config/examples/BQ/Hephestos_2/Configuration_adv.h
@@ -2771,7 +2771,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/BQ/WITBOX/Configuration_adv.h b/config/examples/BQ/WITBOX/Configuration_adv.h
index c83d4f31a87fdd7c5703d4741baccb596e75e1ff..bc8b649b30e79df3e0e5aaac915329ec8573dc51 100644
--- a/config/examples/BQ/WITBOX/Configuration_adv.h
+++ b/config/examples/BQ/WITBOX/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration_adv.h b/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration_adv.h
index 5e71b0d2594e7437d64e062913d53e5267a245ec..cbca51c32cc1753dc9fc422f7941865c6d5628a0 100644
--- a/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration_adv.h
+++ b/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h b/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h
index eea0eb204b5db1d66b0c9cf5cf2b6daf4d6bfa7b..41d6453a256ecc6aef13c51df071ce374aca2570 100644
--- a/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h
+++ b/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Cartesio/Configuration_adv.h b/config/examples/Cartesio/Configuration_adv.h
index 7eec0a40bdbaffad8ebe12827fc7081afe6bb496..20fed00c18dcf019b0d1f0014c1ddad756a4f494 100644
--- a/config/examples/Cartesio/Configuration_adv.h
+++ b/config/examples/Cartesio/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Creality/CR-10/Configuration_adv.h b/config/examples/Creality/CR-10/Configuration_adv.h
index ba91ac3e40ac2bffb218396d7ab3a80df99cd06e..05b76500769f331a150cb6be0d93c1c1f4cc7e22 100644
--- a/config/examples/Creality/CR-10/Configuration_adv.h
+++ b/config/examples/Creality/CR-10/Configuration_adv.h
@@ -2766,7 +2766,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Creality/CR-10S/Configuration_adv.h b/config/examples/Creality/CR-10S/Configuration_adv.h
index bb5496005a733f64b699d33a0eba7863d734479b..b99931263f3e8adfc1f5540c3007aea39b2cad79 100644
--- a/config/examples/Creality/CR-10S/Configuration_adv.h
+++ b/config/examples/Creality/CR-10S/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Creality/CR-10_5S/Configuration_adv.h b/config/examples/Creality/CR-10_5S/Configuration_adv.h
index f3eb54ed9acfab69274aeb7994e3b722becaa9a5..f67c0578e05d6f3cec3048ed8cef9088a64d7199 100644
--- a/config/examples/Creality/CR-10_5S/Configuration_adv.h
+++ b/config/examples/Creality/CR-10_5S/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Creality/CR-10mini/Configuration_adv.h b/config/examples/Creality/CR-10mini/Configuration_adv.h
index 14a7a9c501d4b301133fda9384dc394a6d9a8eb1..b3078a3c887f593eb38a2b0c160315b1c2366723 100644
--- a/config/examples/Creality/CR-10mini/Configuration_adv.h
+++ b/config/examples/Creality/CR-10mini/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Creality/CR-20 Pro/Configuration_adv.h b/config/examples/Creality/CR-20 Pro/Configuration_adv.h
index de9406fdaff10bfefa0025f2bc35b65ca9ec386b..92deade7539bbd159aaeb7c37cc3bf951d942d57 100644
--- a/config/examples/Creality/CR-20 Pro/Configuration_adv.h
+++ b/config/examples/Creality/CR-20 Pro/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Creality/CR-20/Configuration_adv.h b/config/examples/Creality/CR-20/Configuration_adv.h
index 2644688502c8aff23875827a6fefbbab266d5ce9..9c2d7e9c41834b2284e389ca12ed22db36c5c627 100644
--- a/config/examples/Creality/CR-20/Configuration_adv.h
+++ b/config/examples/Creality/CR-20/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Creality/CR-8/Configuration_adv.h b/config/examples/Creality/CR-8/Configuration_adv.h
index 3dcc8319b9709e663baba2ec95cb7cf2ccce20fd..19a0a275189b43970f7e20c95b4c98bd2cc14faf 100644
--- a/config/examples/Creality/CR-8/Configuration_adv.h
+++ b/config/examples/Creality/CR-8/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Creality/Ender-2/Configuration_adv.h b/config/examples/Creality/Ender-2/Configuration_adv.h
index cca4edcd42d5a325e59dbf21a3fa5fcdde5edd86..63a49b28954ed99c15097584ba7e8625e5f9a53a 100644
--- a/config/examples/Creality/Ender-2/Configuration_adv.h
+++ b/config/examples/Creality/Ender-2/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Creality/Ender-3/Configuration_adv.h b/config/examples/Creality/Ender-3/Configuration_adv.h
index 6782e1e80d99c5f6be739f424dc1698251cd7a06..6a8d0218bcd33dff9fbd2ead6fb33f6670c44e11 100644
--- a/config/examples/Creality/Ender-3/Configuration_adv.h
+++ b/config/examples/Creality/Ender-3/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Creality/Ender-4/Configuration_adv.h b/config/examples/Creality/Ender-4/Configuration_adv.h
index 59c4c3d76fd86fbb0a77cc2a9a9e50689056a5a3..7cf287f98658922dcd7961e576b23785d068d5ac 100644
--- a/config/examples/Creality/Ender-4/Configuration_adv.h
+++ b/config/examples/Creality/Ender-4/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Creality/Ender-5 Pro/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/Configuration_adv.h
index 9b6a22674524778207b554a4638ee93d1cdb45fe..f1d1ac09bbd471add42647e8a8f16ebae5722330 100644
--- a/config/examples/Creality/Ender-5 Pro/Configuration_adv.h
+++ b/config/examples/Creality/Ender-5 Pro/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Creality/Ender-5/Configuration_adv.h b/config/examples/Creality/Ender-5/Configuration_adv.h
index a27aea4d97bdbf3cd33e15f749e5854116a7a09c..0ebdd83b5879d2303438c8636331cadccbfcff54 100644
--- a/config/examples/Creality/Ender-5/Configuration_adv.h
+++ b/config/examples/Creality/Ender-5/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h
index 8887422c99c100cdc3381d388383fc8f6bbccb18..774cd6cd721c2a1706afa365582c246371275871 100644
--- a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h
+++ b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h b/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h
index 9bb5b7877199077b445368b130e1d338c8fe3e50..eb76a0b60dfac620480f9b38f47a71e7352ddb64 100644
--- a/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h
+++ b/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h
@@ -2759,7 +2759,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Einstart-S/Configuration_adv.h b/config/examples/Einstart-S/Configuration_adv.h
index ccba5f8063ad586b311b5a3ee246abc56cadca28..11d386d0a87045b5973714723698f5a9f00b0610 100644
--- a/config/examples/Einstart-S/Configuration_adv.h
+++ b/config/examples/Einstart-S/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/FYSETC/AIO_II/Configuration_adv.h b/config/examples/FYSETC/AIO_II/Configuration_adv.h
index 304daa9a7701226d12c125fb8d3706fb1fd8c667..f9f738937dc296a9b3b855fb82aa871d862b42fb 100644
--- a/config/examples/FYSETC/AIO_II/Configuration_adv.h
+++ b/config/examples/FYSETC/AIO_II/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h
index 3ded301674bb18fbb41e1a5ec4774e03c185ccc8..d0dfb609f5adb6c01c1ef620b857ceccb12eadcb 100644
--- a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h
+++ b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h b/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h
index 3ded301674bb18fbb41e1a5ec4774e03c185ccc8..d0dfb609f5adb6c01c1ef620b857ceccb12eadcb 100644
--- a/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h
+++ b/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h b/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h
index 3ded301674bb18fbb41e1a5ec4774e03c185ccc8..d0dfb609f5adb6c01c1ef620b857ceccb12eadcb 100644
--- a/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h
+++ b/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/FYSETC/Cheetah/base/Configuration_adv.h b/config/examples/FYSETC/Cheetah/base/Configuration_adv.h
index 3ded301674bb18fbb41e1a5ec4774e03c185ccc8..d0dfb609f5adb6c01c1ef620b857ceccb12eadcb 100644
--- a/config/examples/FYSETC/Cheetah/base/Configuration_adv.h
+++ b/config/examples/FYSETC/Cheetah/base/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/FYSETC/F6_13/Configuration_adv.h b/config/examples/FYSETC/F6_13/Configuration_adv.h
index 41e90f693ddc8f4d7e25956cfdb02f4f96274430..bcddc512cd69ec4ee06f76a678ffe6e1af2acf96 100644
--- a/config/examples/FYSETC/F6_13/Configuration_adv.h
+++ b/config/examples/FYSETC/F6_13/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/FYSETC/S6/Configuration_adv.h b/config/examples/FYSETC/S6/Configuration_adv.h
index 04ed57cb732dae53e0f35167e22343c16f218f1b..27fbf0d85e9c07f301299c285f3ffcb6f306cb3e 100644
--- a/config/examples/FYSETC/S6/Configuration_adv.h
+++ b/config/examples/FYSETC/S6/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Felix/DUAL/Configuration_adv.h b/config/examples/Felix/DUAL/Configuration_adv.h
index 00c26086d5fdee12583f6203368985531128e51e..af71111093a7558ebd3571375ee724ae62bbe112 100644
--- a/config/examples/Felix/DUAL/Configuration_adv.h
+++ b/config/examples/Felix/DUAL/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Felix/Single/Configuration_adv.h b/config/examples/Felix/Single/Configuration_adv.h
index 00c26086d5fdee12583f6203368985531128e51e..af71111093a7558ebd3571375ee724ae62bbe112 100644
--- a/config/examples/Felix/Single/Configuration_adv.h
+++ b/config/examples/Felix/Single/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/FlashForge/CreatorPro/Configuration_adv.h b/config/examples/FlashForge/CreatorPro/Configuration_adv.h
index 607fab29d3d00fad92914dd96f7fe1d9899a898f..b31419be85b17d8c4c31f0c48c38a1217ed64654 100644
--- a/config/examples/FlashForge/CreatorPro/Configuration_adv.h
+++ b/config/examples/FlashForge/CreatorPro/Configuration_adv.h
@@ -2762,7 +2762,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/config/examples/FolgerTech/i3-2020/Configuration_adv.h
index 118f703ec15f8aae8c4f7a4dd28a95c0dbcfae63..bae7f0442735e8e97b211d73d23604978b29d1bf 100644
--- a/config/examples/FolgerTech/i3-2020/Configuration_adv.h
+++ b/config/examples/FolgerTech/i3-2020/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Formbot/Raptor/Configuration_adv.h b/config/examples/Formbot/Raptor/Configuration_adv.h
index 9bb6c7183d9564e4c8ee3593853ce3b70b03a45f..7121f6ac819a404c6327fa71b35175e05901c9f3 100644
--- a/config/examples/Formbot/Raptor/Configuration_adv.h
+++ b/config/examples/Formbot/Raptor/Configuration_adv.h
@@ -2767,7 +2767,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
index 50d40f4088c26dba24aab157f25692ce4fbebb60..2dd6e53ec7fa6ffca63da3cc7a9d53c3b48cc782 100644
--- a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
+++ b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
@@ -2767,7 +2767,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Formbot/T_Rex_3/Configuration_adv.h b/config/examples/Formbot/T_Rex_3/Configuration_adv.h
index 51b5ea7ca9b72587995ee864b35c76fd90c46fc6..7fae4b7c8297413cfd84edd289ca3486e7d026dd 100644
--- a/config/examples/Formbot/T_Rex_3/Configuration_adv.h
+++ b/config/examples/Formbot/T_Rex_3/Configuration_adv.h
@@ -2762,7 +2762,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Geeetech/A10/Configuration_adv.h b/config/examples/Geeetech/A10/Configuration_adv.h
index bc215e621ef363f85ffc8391dd8d9e0a1a0ac08e..d905e7ba7bfb2899f9bc7d907285416dd4735117 100644
--- a/config/examples/Geeetech/A10/Configuration_adv.h
+++ b/config/examples/Geeetech/A10/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Geeetech/A10D/Configuration_adv.h b/config/examples/Geeetech/A10D/Configuration_adv.h
index 3f57bdd4a367772095d774c71b418fce5857e9c7..e35bd1919624c25e74b40d973f61b655a6f4a8dc 100644
--- a/config/examples/Geeetech/A10D/Configuration_adv.h
+++ b/config/examples/Geeetech/A10D/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Geeetech/A10M/Configuration_adv.h b/config/examples/Geeetech/A10M/Configuration_adv.h
index 001689fc52ecee801201f738b134ac3dd5392d84..0ddeba6a1e2e00df7ac4a5db1763118d2ca9c38c 100644
--- a/config/examples/Geeetech/A10M/Configuration_adv.h
+++ b/config/examples/Geeetech/A10M/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Geeetech/A10T/Configuration_adv.h b/config/examples/Geeetech/A10T/Configuration_adv.h
index 001689fc52ecee801201f738b134ac3dd5392d84..0ddeba6a1e2e00df7ac4a5db1763118d2ca9c38c 100644
--- a/config/examples/Geeetech/A10T/Configuration_adv.h
+++ b/config/examples/Geeetech/A10T/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Geeetech/A20/Configuration_adv.h b/config/examples/Geeetech/A20/Configuration_adv.h
index b1392f016b5bb3db081fa7920b8bd789682c24f6..c64956697f05b69bea0892dccfb7e5338730b5e7 100644
--- a/config/examples/Geeetech/A20/Configuration_adv.h
+++ b/config/examples/Geeetech/A20/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Geeetech/A20M/Configuration_adv.h b/config/examples/Geeetech/A20M/Configuration_adv.h
index b1392f016b5bb3db081fa7920b8bd789682c24f6..c64956697f05b69bea0892dccfb7e5338730b5e7 100644
--- a/config/examples/Geeetech/A20M/Configuration_adv.h
+++ b/config/examples/Geeetech/A20M/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Geeetech/A20T/Configuration_adv.h b/config/examples/Geeetech/A20T/Configuration_adv.h
index b1392f016b5bb3db081fa7920b8bd789682c24f6..c64956697f05b69bea0892dccfb7e5338730b5e7 100644
--- a/config/examples/Geeetech/A20T/Configuration_adv.h
+++ b/config/examples/Geeetech/A20T/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Geeetech/A30/Configuration_adv.h b/config/examples/Geeetech/A30/Configuration_adv.h
index 1f5ae3a092340259e29f5b22b0e89b3932ca0672..99e22b5d8b5db04dbaa53fe0a10436a1d9e6d048 100644
--- a/config/examples/Geeetech/A30/Configuration_adv.h
+++ b/config/examples/Geeetech/A30/Configuration_adv.h
@@ -2762,7 +2762,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Geeetech/D200/Configuration_adv.h b/config/examples/Geeetech/D200/Configuration_adv.h
index 408cee422650933dc4fedf3dd8055678bc3caf5b..43f48d9df094afbaf67fbb9319fc3fe276062364 100644
--- a/config/examples/Geeetech/D200/Configuration_adv.h
+++ b/config/examples/Geeetech/D200/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Geeetech/E180/Configuration_adv.h b/config/examples/Geeetech/E180/Configuration_adv.h
index 1f5ae3a092340259e29f5b22b0e89b3932ca0672..99e22b5d8b5db04dbaa53fe0a10436a1d9e6d048 100644
--- a/config/examples/Geeetech/E180/Configuration_adv.h
+++ b/config/examples/Geeetech/E180/Configuration_adv.h
@@ -2762,7 +2762,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Geeetech/M201/Configuration_adv.h b/config/examples/Geeetech/M201/Configuration_adv.h
index 408cee422650933dc4fedf3dd8055678bc3caf5b..43f48d9df094afbaf67fbb9319fc3fe276062364 100644
--- a/config/examples/Geeetech/M201/Configuration_adv.h
+++ b/config/examples/Geeetech/M201/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Geeetech/MeCreator2/Configuration_adv.h b/config/examples/Geeetech/MeCreator2/Configuration_adv.h
index 0a38e9465d3aabab4138234de9eac44cb4ecc894..b24bcfd769c786864e658d811fd9185719ee79f2 100644
--- a/config/examples/Geeetech/MeCreator2/Configuration_adv.h
+++ b/config/examples/Geeetech/MeCreator2/Configuration_adv.h
@@ -2762,7 +2762,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Geeetech/PI3A PRO/Configuration_adv.h b/config/examples/Geeetech/PI3A PRO/Configuration_adv.h
index 44bfce6ca2d7c6d42479f99f3a764ab053830a0e..4728d2af4944b94c7102e6e3093297f3747bfde5 100644
--- a/config/examples/Geeetech/PI3A PRO/Configuration_adv.h
+++ b/config/examples/Geeetech/PI3A PRO/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
index bc215e621ef363f85ffc8391dd8d9e0a1a0ac08e..d905e7ba7bfb2899f9bc7d907285416dd4735117 100644
--- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
+++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
index bc215e621ef363f85ffc8391dd8d9e0a1a0ac08e..d905e7ba7bfb2899f9bc7d907285416dd4735117 100644
--- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
+++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/HMS434/Configuration_adv.h b/config/examples/HMS434/Configuration_adv.h
index 7a51faedf123cb1360e2cf8ffe502b78ae4a8331..a146e69c2d062331aa59ab0b3bee1c004e07b7d4 100644
--- a/config/examples/HMS434/Configuration_adv.h
+++ b/config/examples/HMS434/Configuration_adv.h
@@ -2755,7 +2755,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Infitary/i3-M508/Configuration_adv.h b/config/examples/Infitary/i3-M508/Configuration_adv.h
index 37802a46244f6d51e026fb0a9af1d4ea4f98921b..bd47a908d9862c2903bda7f3970cc6492accbaf8 100644
--- a/config/examples/Infitary/i3-M508/Configuration_adv.h
+++ b/config/examples/Infitary/i3-M508/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/JGAurora/A1/Configuration_adv.h b/config/examples/JGAurora/A1/Configuration_adv.h
index 9035806b4b3a9a9f4fa3b8fc545dde520ab79a7b..7941eca0077756d3a7ad9d7675026d057be47122 100644
--- a/config/examples/JGAurora/A1/Configuration_adv.h
+++ b/config/examples/JGAurora/A1/Configuration_adv.h
@@ -2768,7 +2768,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/JGAurora/A5/Configuration_adv.h b/config/examples/JGAurora/A5/Configuration_adv.h
index e4d05182b92b3c76a356fec8f72a844c77a4d9e6..d6700d00f2e53f970080ff4230742321782852fd 100644
--- a/config/examples/JGAurora/A5/Configuration_adv.h
+++ b/config/examples/JGAurora/A5/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/JGAurora/A5S/Configuration_adv.h b/config/examples/JGAurora/A5S/Configuration_adv.h
index 9035806b4b3a9a9f4fa3b8fc545dde520ab79a7b..7941eca0077756d3a7ad9d7675026d057be47122 100644
--- a/config/examples/JGAurora/A5S/Configuration_adv.h
+++ b/config/examples/JGAurora/A5S/Configuration_adv.h
@@ -2768,7 +2768,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/JGAurora/Magic/Configuration_adv.h b/config/examples/JGAurora/Magic/Configuration_adv.h
index 7542701fd8866880c3244fc2e7ebd08c493c5ae0..02b28a052ab38f686b5e3ffa479c61c8e41293c8 100644
--- a/config/examples/JGAurora/Magic/Configuration_adv.h
+++ b/config/examples/JGAurora/Magic/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h b/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h
index 8ddba43d72b1ead42c26daf4d3d8ef1363fb113d..41212bfaf09d6623cef0140c634b175d03b80d52 100644
--- a/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h
+++ b/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h
@@ -2760,7 +2760,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/MakerParts/Configuration_adv.h b/config/examples/MakerParts/Configuration_adv.h
index a3a99987e497c18bec47556c9baf0470ac334206..22319f3ebbb2ea07dd6a425abdfce9a49f5b5adc 100644
--- a/config/examples/MakerParts/Configuration_adv.h
+++ b/config/examples/MakerParts/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Malyan/M150/Configuration_adv.h b/config/examples/Malyan/M150/Configuration_adv.h
index a71325f2a07668b56399004eb0eac5896c49c1b8..6c632fa27c2dfe296e1a40fc10e265243c9d98e6 100644
--- a/config/examples/Malyan/M150/Configuration_adv.h
+++ b/config/examples/Malyan/M150/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Malyan/M200/Configuration_adv.h b/config/examples/Malyan/M200/Configuration_adv.h
index 25842a8ae4fb83fd18d7f460d36a8f2d87693ebc..d6ccfe88b5744e81968e658afa5b45ef3c86a582 100644
--- a/config/examples/Malyan/M200/Configuration_adv.h
+++ b/config/examples/Malyan/M200/Configuration_adv.h
@@ -2765,7 +2765,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/config/examples/Micromake/C1/enhanced/Configuration_adv.h
index fb946ba21aaa5f9e79d79a6b33763b6738ab9f0c..2688b44d2e82ad58502e193fcb41bf687650be03 100644
--- a/config/examples/Micromake/C1/enhanced/Configuration_adv.h
+++ b/config/examples/Micromake/C1/enhanced/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Mks/Robin/Configuration_adv.h b/config/examples/Mks/Robin/Configuration_adv.h
index 90c9dbab437648a592cd879e2db20396a74086cc..b6a6538806656b6c0dccc240b82b56fc69fedcff 100644
--- a/config/examples/Mks/Robin/Configuration_adv.h
+++ b/config/examples/Mks/Robin/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Mks/Sbase/Configuration_adv.h b/config/examples/Mks/Sbase/Configuration_adv.h
index 49fdbf982c6c06315a7ea0dbec1d0ba975563d3d..bc59e1a935241ef513d60b650d149bea42ef75c2 100644
--- a/config/examples/Mks/Sbase/Configuration_adv.h
+++ b/config/examples/Mks/Sbase/Configuration_adv.h
@@ -2764,7 +2764,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Modix/Big60/Configuration_adv.h b/config/examples/Modix/Big60/Configuration_adv.h
index dbde1ff15bbc8973b2059592ba384757bb56b75d..35494a41f3fffc9123a986dd9560d19d51f138c2 100644
--- a/config/examples/Modix/Big60/Configuration_adv.h
+++ b/config/examples/Modix/Big60/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/RapideLite/RL200/Configuration_adv.h b/config/examples/RapideLite/RL200/Configuration_adv.h
index 997a15a4012c276b464d86d43c27ce3828950c6b..bcb251445df6af95b500117dd0a9e0a99fe36c4e 100644
--- a/config/examples/RapideLite/RL200/Configuration_adv.h
+++ b/config/examples/RapideLite/RL200/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Renkforce/RF100/Configuration_adv.h b/config/examples/Renkforce/RF100/Configuration_adv.h
index d25a5d025ea2908b7938ee1b0239b5ba23dd7119..881c8b303d217138255de6f76ac8f7093c9b25ce 100644
--- a/config/examples/Renkforce/RF100/Configuration_adv.h
+++ b/config/examples/Renkforce/RF100/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Renkforce/RF100XL/Configuration_adv.h b/config/examples/Renkforce/RF100XL/Configuration_adv.h
index d25a5d025ea2908b7938ee1b0239b5ba23dd7119..881c8b303d217138255de6f76ac8f7093c9b25ce 100644
--- a/config/examples/Renkforce/RF100XL/Configuration_adv.h
+++ b/config/examples/Renkforce/RF100XL/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Renkforce/RF100v2/Configuration_adv.h b/config/examples/Renkforce/RF100v2/Configuration_adv.h
index d25a5d025ea2908b7938ee1b0239b5ba23dd7119..881c8b303d217138255de6f76ac8f7093c9b25ce 100644
--- a/config/examples/Renkforce/RF100v2/Configuration_adv.h
+++ b/config/examples/Renkforce/RF100v2/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/RigidBot/Configuration_adv.h b/config/examples/RigidBot/Configuration_adv.h
index 72bea9fb262f0a19a70b798e27c28ad41633e33f..b9675b36348561ce4e6b7b89dca3b39ec880d4e5 100644
--- a/config/examples/RigidBot/Configuration_adv.h
+++ b/config/examples/RigidBot/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/SCARA/MP_SCARA/Configuration_adv.h b/config/examples/SCARA/MP_SCARA/Configuration_adv.h
index 5f3a2281b9790124d2ecbfde995d1c5fc5fbbd04..47b319dc86139cb4e97386ee7a8e23332c046be1 100644
--- a/config/examples/SCARA/MP_SCARA/Configuration_adv.h
+++ b/config/examples/SCARA/MP_SCARA/Configuration_adv.h
@@ -2616,7 +2616,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/SCARA/Morgan/Configuration_adv.h b/config/examples/SCARA/Morgan/Configuration_adv.h
index 1afcdb5e254fb454311d11fa493f59bdc80f47ea..d69476b520924117911e7093895bc9c51626714e 100644
--- a/config/examples/SCARA/Morgan/Configuration_adv.h
+++ b/config/examples/SCARA/Morgan/Configuration_adv.h
@@ -2760,7 +2760,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
index 05e01fcbfaf45805ba3c0da6250a4019cb03d1b6..5457678ad44ca9145295c979d261490886ef7819 100644
--- a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
+++ b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Sanguinololu/Configuration_adv.h b/config/examples/Sanguinololu/Configuration_adv.h
index 6ee203a516bb184485a1580de100e4ffd10d27cf..dd4eb94f4e8c7176345cc56b29c72fe905128cff 100644
--- a/config/examples/Sanguinololu/Configuration_adv.h
+++ b/config/examples/Sanguinololu/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Tevo/Michelangelo/Configuration_adv.h b/config/examples/Tevo/Michelangelo/Configuration_adv.h
index 12c0e2469c64b633d1023d474fe2907609a2e085..87a4ac48562bfbc42523f1aa45d74629be5bda51 100644
--- a/config/examples/Tevo/Michelangelo/Configuration_adv.h
+++ b/config/examples/Tevo/Michelangelo/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Tevo/Nereus/Configuration_adv.h b/config/examples/Tevo/Nereus/Configuration_adv.h
index c02e567ca7d70b1aceef895840688317d5ab1ce9..7d2ea316a8785fdc4654f10f36a12f7c1093ba7c 100755
--- a/config/examples/Tevo/Nereus/Configuration_adv.h
+++ b/config/examples/Tevo/Nereus/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h
index 90e4034a7247263ffdf58a109b72b17d550efc25..f3d1045aee62d527dac7e079fe146a886032ac77 100755
--- a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h
+++ b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h
index c04ec1ff805e25b374429825d721f7d95b9024bc..6ad36bc9e2f254eb54a91fa9f9e0a6fbf776033b 100755
--- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h
+++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h
index c04ec1ff805e25b374429825d721f7d95b9024bc..6ad36bc9e2f254eb54a91fa9f9e0a6fbf776033b 100755
--- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h
+++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/TheBorg/Configuration_adv.h b/config/examples/TheBorg/Configuration_adv.h
index a05c1b82652a28972ce4e190e7648008666383d3..cbde07da675a455e00517550bcd1aeebc47d3f07 100644
--- a/config/examples/TheBorg/Configuration_adv.h
+++ b/config/examples/TheBorg/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/TinyBoy2/Configuration_adv.h b/config/examples/TinyBoy2/Configuration_adv.h
index f0ae23b3f1b66910f1d2d56fcdea4a97ae6cfd75..76932479224cd3f7900604637f023ec256a1bdd3 100644
--- a/config/examples/TinyBoy2/Configuration_adv.h
+++ b/config/examples/TinyBoy2/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Tronxy/X3A/Configuration_adv.h b/config/examples/Tronxy/X3A/Configuration_adv.h
index f85383b0fb07ef9035bb503a157c41ac6248f76e..62658dd4e3df44eed3e836ccd8ce01031bf3f09f 100644
--- a/config/examples/Tronxy/X3A/Configuration_adv.h
+++ b/config/examples/Tronxy/X3A/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Tronxy/X5S-2E/Configuration_adv.h b/config/examples/Tronxy/X5S-2E/Configuration_adv.h
index 75236c8bb1d99c84be4171ac20399f24785be7ff..0e98cbc2c1ecd9253fc9c32490dde19d87268162 100644
--- a/config/examples/Tronxy/X5S-2E/Configuration_adv.h
+++ b/config/examples/Tronxy/X5S-2E/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/UltiMachine/Archim1/Configuration_adv.h b/config/examples/UltiMachine/Archim1/Configuration_adv.h
index 47b8d9e46e056128a057084b6dc34b23ab516c69..1ca189266a96a6552cddd51b558ccb451f3cdc8a 100644
--- a/config/examples/UltiMachine/Archim1/Configuration_adv.h
+++ b/config/examples/UltiMachine/Archim1/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/UltiMachine/Archim2/Configuration_adv.h b/config/examples/UltiMachine/Archim2/Configuration_adv.h
index 19092a5c5a516b5b72bf16ba0bfcb876937b7aa0..99c860659f95b162eda3417e0334c881d5d542b2 100644
--- a/config/examples/UltiMachine/Archim2/Configuration_adv.h
+++ b/config/examples/UltiMachine/Archim2/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/VORONDesign/Configuration_adv.h b/config/examples/VORONDesign/Configuration_adv.h
index 9301901808211512983c29008ef19470b08fbcd5..04a2e49965b5fea36ad801f10f4e34dec12d7d26 100644
--- a/config/examples/VORONDesign/Configuration_adv.h
+++ b/config/examples/VORONDesign/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Velleman/K8200/Configuration_adv.h b/config/examples/Velleman/K8200/Configuration_adv.h
index 51640c0a5ceb881c1a34bc34ef158b61e0f6e718..19978fc652623efd0243aff3f3bea89b532a6347 100644
--- a/config/examples/Velleman/K8200/Configuration_adv.h
+++ b/config/examples/Velleman/K8200/Configuration_adv.h
@@ -2776,7 +2776,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h
index 344b75b213433a63e13b30fb25e2c4ea9f6fe5b8..14f56db3cd19690411237a1c7bf79c6a240eeea6 100644
--- a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h
+++ b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h
index 344b75b213433a63e13b30fb25e2c4ea9f6fe5b8..14f56db3cd19690411237a1c7bf79c6a240eeea6 100644
--- a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h
+++ b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/WASP/PowerWASP/Configuration_adv.h b/config/examples/WASP/PowerWASP/Configuration_adv.h
index 0604afed73616c2caf9fa91b17875162049865df..127e0c20b883bbc4ca19816dfea0c7e0517a177e 100644
--- a/config/examples/WASP/PowerWASP/Configuration_adv.h
+++ b/config/examples/WASP/PowerWASP/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
index 9f18c6288607349d8648e2dcfc8f699f612d11c2..6f95b25cac7b842ee8c54821ad257dfce5fca0ac 100644
--- a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
+++ b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
@@ -2765,7 +2765,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h
index f4eecf9d6656b9a573463ab9e52593233e49f049..0235859d3cf53d0161b860a0f8f0b04606185779 100644
--- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h
+++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h
index f33bdfa10266d3c3eb5a4fc2cbabf1cfba350959..61d023dfcabb9facf5bf80c8cb13d1d075c186e4 100644
--- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h
+++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h
index 67f224a1e90a7bbffb68a8adc42c9f92a2680b0b..48c3ca0af4c0cd518abef0a4d6ba36ca5809c659 100644
--- a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h
+++ b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h
@@ -2765,7 +2765,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h
index 008d05a5b7e0b87646ae7914abee5c891fe393f4..0e0002b3ab59696ccddc26ee3108378ebdb5a1ff 100644
--- a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h
+++ b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h
@@ -2764,7 +2764,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h
index bce8576ae6b465868eed0a2aa98c2b932bf92f37..2bafa9cd704416c4271c02c337a732563f0464e3 100644
--- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h
+++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h
@@ -2765,7 +2765,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h b/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h
index 86bcf015ac341198db8403a5a7e322a7db632adc..c37de68a3edb2aca5f6b39b929f72aa6102b5171 100644
--- a/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h
+++ b/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h
@@ -2765,7 +2765,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
index b5fdd58180c7565f6a7619d8f5f5edaf9830d261..7e277f2a530f330c39e7df9fd2d092b583db5b12 100644
--- a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
+++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
@@ -2765,7 +2765,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/config/examples/delta/FLSUN/kossel/Configuration_adv.h
index b5fdd58180c7565f6a7619d8f5f5edaf9830d261..7e277f2a530f330c39e7df9fd2d092b583db5b12 100644
--- a/config/examples/delta/FLSUN/kossel/Configuration_adv.h
+++ b/config/examples/delta/FLSUN/kossel/Configuration_adv.h
@@ -2765,7 +2765,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
index 8d3a5f30282fdf9300e81b17ec65e927bbea02f0..502533dc11094f4227d0d28f150e6c4161fa624d 100644
--- a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
+++ b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
@@ -2765,7 +2765,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h
index f7ba1d7d90f9531fc4ff9a4df8386bd325192fe8..f9f3a9082b081fd7085f9a5bdf5911862ee4f99c 100644
--- a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h
+++ b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h
@@ -2765,7 +2765,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/delta/MKS/SBASE/Configuration_adv.h b/config/examples/delta/MKS/SBASE/Configuration_adv.h
index 512ff392976abca454f3c355e4bd8fbe3c6a9609..f0a442add696d91e6d3ba860b981ac167b5be511 100644
--- a/config/examples/delta/MKS/SBASE/Configuration_adv.h
+++ b/config/examples/delta/MKS/SBASE/Configuration_adv.h
@@ -2765,7 +2765,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/delta/Tevo Little Monster/Configuration_adv.h b/config/examples/delta/Tevo Little Monster/Configuration_adv.h
index fffdb639fb9616f2bfbf9a5db303b89feb36e706..10ce3ce224f670d0c13d5d203f6a5c009c7d05c2 100644
--- a/config/examples/delta/Tevo Little Monster/Configuration_adv.h
+++ b/config/examples/delta/Tevo Little Monster/Configuration_adv.h
@@ -2765,7 +2765,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/delta/generic/Configuration_adv.h b/config/examples/delta/generic/Configuration_adv.h
index 8d3a5f30282fdf9300e81b17ec65e927bbea02f0..502533dc11094f4227d0d28f150e6c4161fa624d 100644
--- a/config/examples/delta/generic/Configuration_adv.h
+++ b/config/examples/delta/generic/Configuration_adv.h
@@ -2765,7 +2765,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/delta/kossel_clear/Configuration_adv.h b/config/examples/delta/kossel_clear/Configuration_adv.h
index 4ef59e440b10e858aeb22fb0ecbd0672ca85eed5..0316631df95aa69dd45cd0da6ed21449481b7b30 100644
--- a/config/examples/delta/kossel_clear/Configuration_adv.h
+++ b/config/examples/delta/kossel_clear/Configuration_adv.h
@@ -2765,7 +2765,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/delta/kossel_mini/Configuration_adv.h b/config/examples/delta/kossel_mini/Configuration_adv.h
index 8d3a5f30282fdf9300e81b17ec65e927bbea02f0..502533dc11094f4227d0d28f150e6c4161fa624d 100644
--- a/config/examples/delta/kossel_mini/Configuration_adv.h
+++ b/config/examples/delta/kossel_mini/Configuration_adv.h
@@ -2765,7 +2765,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/delta/kossel_xl/Configuration_adv.h b/config/examples/delta/kossel_xl/Configuration_adv.h
index d61a8e293a4d335e9bf7e33a1348ae9fc6fdc9ba..5832d0c0a1637fc10ee085b6d915c32caea3d5b8 100644
--- a/config/examples/delta/kossel_xl/Configuration_adv.h
+++ b/config/examples/delta/kossel_xl/Configuration_adv.h
@@ -2765,7 +2765,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/config/examples/gCreate/gMax1.5+/Configuration_adv.h
index 4e68fb771672e6b307ac7913f542feaed2ee09f4..dc7be02c673503b80f261e848032ac361817176c 100644
--- a/config/examples/gCreate/gMax1.5+/Configuration_adv.h
+++ b/config/examples/gCreate/gMax1.5+/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/makibox/Configuration_adv.h b/config/examples/makibox/Configuration_adv.h
index a719f7e5d4702d87581e586625927e3d7f614a76..6198346b2240aeafa55bac8d8141866b3894e1f9 100644
--- a/config/examples/makibox/Configuration_adv.h
+++ b/config/examples/makibox/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/tvrrug/Round2/Configuration_adv.h b/config/examples/tvrrug/Round2/Configuration_adv.h
index 9a9665c77c9f319cee52d23d58c6764352378ebf..9000e207f3be476877e986a69d08c9bae6b47315 100644
--- a/config/examples/tvrrug/Round2/Configuration_adv.h
+++ b/config/examples/tvrrug/Round2/Configuration_adv.h
@@ -2763,7 +2763,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
diff --git a/config/examples/wt150/Configuration_adv.h b/config/examples/wt150/Configuration_adv.h
index 6c1645554576a33ed26bb4d3604ed18f7244e29a..50a361af6a064ac85d85e31e98c305e6e856420f 100644
--- a/config/examples/wt150/Configuration_adv.h
+++ b/config/examples/wt150/Configuration_adv.h
@@ -2764,7 +2764,11 @@
#define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
#define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
- // Use M119 to find reasonable values after connecting your hardware:
+ //#define INVERT_JOY_X // Enable if X direction is reversed
+ //#define INVERT_JOY_Y // Enable if Y direction is reversed
+ //#define INVERT_JOY_Z // Enable if Z direction is reversed
+
+ // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
#define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
#define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
#define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }