diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 5c318507a4433c8201f2ab08e54b68abb97348d7..236121b71e7970280684ba451316f8bf62215428 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2266,7 +2266,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2326,7 +2326,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/Marlin/src/feature/bltouch.cpp b/Marlin/src/feature/bltouch.cpp
index c42af565e67dad8a190a394a5b6a10fd2964a559..6166b7d195447171420cbce2cf01ea2fdfa3e8e6 100644
--- a/Marlin/src/feature/bltouch.cpp
+++ b/Marlin/src/feature/bltouch.cpp
@@ -114,7 +114,7 @@ bool BLTouch::stow_proc() {
// At the moment that we come in here, we might (pulse) or will (SW mode) see the trigger on the pin.
// So even though we know a STOW will be ignored if an ALARM condition is active, we will STOW.
// Note: If the probe is deployed AND in an ALARM condition, this STOW will not pull up the pin
- // and the ALARM condition will still be there. --> ANTClabs should change this behaviour maybe
+ // and the ALARM condition will still be there. --> ANTClabs should change this behavior maybe
// Attempt to STOW, wait for STOW_DELAY or ALARM
if (_stow_query_alarm()) {
diff --git a/Marlin/src/gcode/bedlevel/G26.cpp b/Marlin/src/gcode/bedlevel/G26.cpp
index cdc2b7478eab247a164a511e19a7546d3252796a..c847141873ef3cff218bc86baefcb8c84da7d464 100644
--- a/Marlin/src/gcode/bedlevel/G26.cpp
+++ b/Marlin/src/gcode/bedlevel/G26.cpp
@@ -87,7 +87,7 @@
* D Disable Disable the Unified Bed Leveling System. In the normal case the user is invoking this
* command to see how well a Mesh as been adjusted to match a print surface. In order to do
* this the Unified Bed Leveling System is turned on by the G26 command. The D parameter
- * alters the command's normal behaviour and disables the Unified Bed Leveling System even if
+ * alters the command's normal behavior and disables the Unified Bed Leveling System even if
* it is on.
*
* H # Hotend Set the Nozzle Temperature. If not specified, a default of 205 C. will be assumed.
@@ -131,7 +131,7 @@
* U # Random Randomize the order that the circles are drawn on the bed. The search for the closest
* un-drawn circle is still done. But the distance to the location for each circle has a
* random number of the specified size added to it. Specifying S50 will give an interesting
- * deviation from the normal behaviour on a 10 x 10 Mesh.
+ * deviation from the normal behavior on a 10 x 10 Mesh.
*
* X # X Coord. Specify the starting location of the drawing activity.
*
diff --git a/Marlin/src/gcode/config/M301.cpp b/Marlin/src/gcode/config/M301.cpp
index 531aa88db3fe9a6da49bbfdc5edca685c9d23c45..f9ebe9b82289407e44a1cc7765dcfb121030efa6 100644
--- a/Marlin/src/gcode/config/M301.cpp
+++ b/Marlin/src/gcode/config/M301.cpp
@@ -42,7 +42,7 @@
void GcodeSuite::M301() {
// multi-extruder PID patch: M301 updates or prints a single extruder's PID values
- // default behaviour (omitting E parameter) is to update for extruder 0 only
+ // default behavior (omitting E parameter) is to update for extruder 0 only
const uint8_t e = parser.byteval('E'); // extruder being updated
if (e < HOTENDS) { // catch bad input value
diff --git a/Marlin/src/gcode/control/M999.cpp b/Marlin/src/gcode/control/M999.cpp
index 8ddbf859e7d33342d97388f34040a4cdfe7453fd..1d2dfae73384e872eb6da27c44738ef8cbd83bd6 100644
--- a/Marlin/src/gcode/control/M999.cpp
+++ b/Marlin/src/gcode/control/M999.cpp
@@ -29,7 +29,7 @@
/**
* M999: Restart after being stopped
*
- * Default behaviour is to flush the serial buffer and request
+ * Default behavior is to flush the serial buffer and request
* a resend to the host starting on the last N line received.
*
* Sending "M999 S1" will resume printing without flushing the
diff --git a/Marlin/src/module/thermistor/thermistor_20.h b/Marlin/src/module/thermistor/thermistor_20.h
index fa1a7568124269fdf8563ea6ebc9c6bd939b1467..7619bfc78fed39083a9500b48dd91ef60a458e2b 100644
--- a/Marlin/src/module/thermistor/thermistor_20.h
+++ b/Marlin/src/module/thermistor/thermistor_20.h
@@ -22,7 +22,7 @@
// PT100 with INA826 amp on Ultimaker v2.0 electronics
// The PT100 in the Ultimaker v2.0 electronics has a high sample value for a high temperature.
-// This does not match the normal thermistor behaviour so we need to set the following defines
+// This does not match the normal thermistor behavior so we need to set the following defines
#if THERMISTOR_HEATER_0 == 20
#define HEATER_0_RAW_HI_TEMP 16383
#define HEATER_0_RAW_LO_TEMP 0
diff --git a/config/default/Configuration_adv.h b/config/default/Configuration_adv.h
index fc2ddb76f1fef1ce0d242135937a1ff4e7b8e195..a9a15211f3b3b6c0de9aff7cfaa7e5e4dea5c2f6 100644
--- a/config/default/Configuration_adv.h
+++ b/config/default/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
index 788e58f8b82a5f75bef17dd5459092a959d5d725..4f40b804129e2e13f8e699da6b4e4946bc22e170 100644
--- a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
+++ b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2270,7 +2270,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2330,7 +2330,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/config/examples/AlephObjects/TAZ4/Configuration_adv.h
index 260899ac8765a9a2c157de5ab6dc5bc3ac2f3455..44227d4d0fb9330512ab0ee0c8e6c5d3dc4e3b98 100644
--- a/config/examples/AlephObjects/TAZ4/Configuration_adv.h
+++ b/config/examples/AlephObjects/TAZ4/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/AliExpress/UM2pExt/Configuration_adv.h b/config/examples/AliExpress/UM2pExt/Configuration_adv.h
index 5a98ffe6bf02015b8e9e88c1106b0ae3feeb4128..160cb86f4a6dbc3c430049e926b86cdc3d33cb97 100644
--- a/config/examples/AliExpress/UM2pExt/Configuration_adv.h
+++ b/config/examples/AliExpress/UM2pExt/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2270,7 +2270,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2330,7 +2330,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Anet/A2/Configuration_adv.h b/config/examples/Anet/A2/Configuration_adv.h
index 32aedb9fd4b4ae040cae3288d7853c23c2b3b8fc..9ace82c328e64cc797f53bd6bdf3e1fc3e1d4369 100644
--- a/config/examples/Anet/A2/Configuration_adv.h
+++ b/config/examples/Anet/A2/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Anet/A2plus/Configuration_adv.h b/config/examples/Anet/A2plus/Configuration_adv.h
index 32aedb9fd4b4ae040cae3288d7853c23c2b3b8fc..9ace82c328e64cc797f53bd6bdf3e1fc3e1d4369 100644
--- a/config/examples/Anet/A2plus/Configuration_adv.h
+++ b/config/examples/Anet/A2plus/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Anet/A6/Configuration_adv.h b/config/examples/Anet/A6/Configuration_adv.h
index 0d072b5aaf3be680c26b23d7cf1189bacacad602..e0b52cb7b36e65b4b8d46f637562e94d9e678388 100644
--- a/config/examples/Anet/A6/Configuration_adv.h
+++ b/config/examples/Anet/A6/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Anet/A8/Configuration_adv.h b/config/examples/Anet/A8/Configuration_adv.h
index a51ac18d71f4db75cbd0cfcd3bf9557a03e75ef4..083c067f0fb27673c173006325d7910dc8a81fc9 100644
--- a/config/examples/Anet/A8/Configuration_adv.h
+++ b/config/examples/Anet/A8/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Anet/A8plus/Configuration_adv.h b/config/examples/Anet/A8plus/Configuration_adv.h
index e59c6c99ec21663e3e92fb820cbffa554dd44bb4..4b3003f9792fd4e6bb1981f65c60ddc0460d3b91 100644
--- a/config/examples/Anet/A8plus/Configuration_adv.h
+++ b/config/examples/Anet/A8plus/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2266,7 +2266,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2326,7 +2326,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Anet/E16/Configuration_adv.h b/config/examples/Anet/E16/Configuration_adv.h
index 5c74d313d6b707f22e0b1a6e938f0431a3e65c8e..5ef03528bd42a4f3a856c0d4ae136a3b7f75a177 100644
--- a/config/examples/Anet/E16/Configuration_adv.h
+++ b/config/examples/Anet/E16/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/AnyCubic/i3/Configuration_adv.h b/config/examples/AnyCubic/i3/Configuration_adv.h
index e68721807f356a41b76049ea4133c1e4fc7c7dfb..6abd184f4375589c9c2e305b64adea632cb9cb90 100644
--- a/config/examples/AnyCubic/i3/Configuration_adv.h
+++ b/config/examples/AnyCubic/i3/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/ArmEd/Configuration_adv.h b/config/examples/ArmEd/Configuration_adv.h
index 143fd076f3f8b778e4fe7aff07ed2ce12f3731d0..382abf1d9975d5e0965c01cbb82f0295cdb082dc 100644
--- a/config/examples/ArmEd/Configuration_adv.h
+++ b/config/examples/ArmEd/Configuration_adv.h
@@ -320,7 +320,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2272,7 +2272,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2332,7 +2332,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
index 0df6bbe0dc45abba5b79d8f86ebf545bb14222a4..00423bcd5be8e75da3e696991dd74e08b12fcfd8 100644
--- a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
+++ b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/BIBO/TouchX/default/Configuration_adv.h b/config/examples/BIBO/TouchX/default/Configuration_adv.h
index 800245d4253576dcc7b3bf8cfc3b1d3a4b5b2eb9..54ffd7cbd1e2a1f261f3b779742e8502bb91ce8d 100644
--- a/config/examples/BIBO/TouchX/default/Configuration_adv.h
+++ b/config/examples/BIBO/TouchX/default/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/BQ/Hephestos/Configuration_adv.h b/config/examples/BQ/Hephestos/Configuration_adv.h
index caea74b4b973a7270dd343024a527257bbf6b4c1..129a6b33e90b99e0d6734d4ca85c006e1ba437ed 100644
--- a/config/examples/BQ/Hephestos/Configuration_adv.h
+++ b/config/examples/BQ/Hephestos/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2265,7 +2265,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2325,7 +2325,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/BQ/Hephestos_2/Configuration_adv.h b/config/examples/BQ/Hephestos_2/Configuration_adv.h
index c7a2637edf05f23b554c6e9c487f506571229f55..e918c47ce00dede6e75ef1bc0b6d81b7f2598cf1 100644
--- a/config/examples/BQ/Hephestos_2/Configuration_adv.h
+++ b/config/examples/BQ/Hephestos_2/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2273,7 +2273,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2333,7 +2333,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/BQ/WITBOX/Configuration_adv.h b/config/examples/BQ/WITBOX/Configuration_adv.h
index caea74b4b973a7270dd343024a527257bbf6b4c1..129a6b33e90b99e0d6734d4ca85c006e1ba437ed 100644
--- a/config/examples/BQ/WITBOX/Configuration_adv.h
+++ b/config/examples/BQ/WITBOX/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2265,7 +2265,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2325,7 +2325,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Cartesio/Configuration_adv.h b/config/examples/Cartesio/Configuration_adv.h
index 904d2e6e6f3344a3c63483a44a65a7735b14f430..ba2a6fb92b5cb2179d7373d8ff01a05ce51c7f83 100644
--- a/config/examples/Cartesio/Configuration_adv.h
+++ b/config/examples/Cartesio/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Creality/CR-10/Configuration_adv.h b/config/examples/Creality/CR-10/Configuration_adv.h
index 91b658bb46fecd2fd644c19ce887ae61ae76e3ad..0af4542443b1091f3acad8f36d3d2d5a2ddc82d9 100644
--- a/config/examples/Creality/CR-10/Configuration_adv.h
+++ b/config/examples/Creality/CR-10/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2271,7 +2271,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2331,7 +2331,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Creality/CR-10S/Configuration_adv.h b/config/examples/Creality/CR-10S/Configuration_adv.h
index cc07ab5bf2ff09739d8d590709ad01202a4c2237..828dbab2981abce490809f35c2062853190459f3 100644
--- a/config/examples/Creality/CR-10S/Configuration_adv.h
+++ b/config/examples/Creality/CR-10S/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Creality/CR-10_5S/Configuration_adv.h b/config/examples/Creality/CR-10_5S/Configuration_adv.h
index 4d85499a98571ff9077ec4bd5124d4cd65041b29..e2b04629657dae2a4166bfda75808524b8c5a4c7 100644
--- a/config/examples/Creality/CR-10_5S/Configuration_adv.h
+++ b/config/examples/Creality/CR-10_5S/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Creality/CR-10mini/Configuration_adv.h b/config/examples/Creality/CR-10mini/Configuration_adv.h
index fca675a23bb9c56201e32f3a9db49bfcb01d6c11..af56eb00ab7f54ea96d56a5338e856ddf9c0e1ec 100644
--- a/config/examples/Creality/CR-10mini/Configuration_adv.h
+++ b/config/examples/Creality/CR-10mini/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Creality/CR-8/Configuration_adv.h b/config/examples/Creality/CR-8/Configuration_adv.h
index 14c873ed2a2a25863be32e8b96e9746a617f8d2b..cdce19034566e40c312ddabd97b5664cfc030632 100644
--- a/config/examples/Creality/CR-8/Configuration_adv.h
+++ b/config/examples/Creality/CR-8/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Creality/Ender-2/Configuration_adv.h b/config/examples/Creality/Ender-2/Configuration_adv.h
index 6798cc5b288feae4530c9d7d4c23d2df834ca56b..a38c1dc2674f6c795857c33067e3ff376bfc79dd 100644
--- a/config/examples/Creality/Ender-2/Configuration_adv.h
+++ b/config/examples/Creality/Ender-2/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2265,7 +2265,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2325,7 +2325,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Creality/Ender-3/Configuration_adv.h b/config/examples/Creality/Ender-3/Configuration_adv.h
index 709ff4e3aebbd9f9bf0c51d9bba2f58a0d86f1eb..af2e7764990ab1c2e1030d714e6e9774d1e4e227 100644
--- a/config/examples/Creality/Ender-3/Configuration_adv.h
+++ b/config/examples/Creality/Ender-3/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2265,7 +2265,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2325,7 +2325,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Creality/Ender-4/Configuration_adv.h b/config/examples/Creality/Ender-4/Configuration_adv.h
index 81ac92f850471725f6aaf32a32ef58b9179a0ee6..b01b8fca1d7574e90d0d044832ec8888dbafdffc 100644
--- a/config/examples/Creality/Ender-4/Configuration_adv.h
+++ b/config/examples/Creality/Ender-4/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Einstart-S/Configuration_adv.h b/config/examples/Einstart-S/Configuration_adv.h
index 40df8a7d913c00a131b6ac629b2fe7d179fc9873..5a15ddd21b0b2587fbb1c535e7f46f45721cf2dc 100644
--- a/config/examples/Einstart-S/Configuration_adv.h
+++ b/config/examples/Einstart-S/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Felix/Configuration_adv.h b/config/examples/Felix/Configuration_adv.h
index d9e68ae5f8edaf6961cb529ff1ec53a1d5773f57..03bdafa5c7f8d255d010975cfad625c39e075087 100644
--- a/config/examples/Felix/Configuration_adv.h
+++ b/config/examples/Felix/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/FlashForge/CreatorPro/Configuration_adv.h b/config/examples/FlashForge/CreatorPro/Configuration_adv.h
index 33986fe856cacf73ca53eae4aba69752b0ad6065..0c62be5536d3ae098d9ab3a958419f6a9f590d38 100644
--- a/config/examples/FlashForge/CreatorPro/Configuration_adv.h
+++ b/config/examples/FlashForge/CreatorPro/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2264,7 +2264,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2324,7 +2324,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/config/examples/FolgerTech/i3-2020/Configuration_adv.h
index a13f1bf9a4e403828a5928960c2cb0268009fb8a..0caa02b4406785066086e81e171b670d68d9f1e1 100644
--- a/config/examples/FolgerTech/i3-2020/Configuration_adv.h
+++ b/config/examples/FolgerTech/i3-2020/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2336,7 +2336,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Formbot/Raptor/Configuration_adv.h b/config/examples/Formbot/Raptor/Configuration_adv.h
index 2c3708abdb1191667bb2dd06dbed9dd4fd89b14d..f7418ee67f5c69bb7cfb3a9dae85fae6736e0bfd 100644
--- a/config/examples/Formbot/Raptor/Configuration_adv.h
+++ b/config/examples/Formbot/Raptor/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2272,7 +2272,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2332,7 +2332,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
index c8fb69737d1377cfc468bf859a8ec58762c530f3..29776b3cc148c68a86c69f71252ba2462530f27f 100644
--- a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
+++ b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2272,7 +2272,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2342,7 +2342,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Formbot/T_Rex_3/Configuration_adv.h b/config/examples/Formbot/T_Rex_3/Configuration_adv.h
index 272c0e0c84d029bf1667d57d32197540e15639e1..5f81cfaf418b408b353f4ba633180603c4d43d99 100644
--- a/config/examples/Formbot/T_Rex_3/Configuration_adv.h
+++ b/config/examples/Formbot/T_Rex_3/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2267,7 +2267,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2337,7 +2337,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Geeetech/A10M/Configuration_adv.h b/config/examples/Geeetech/A10M/Configuration_adv.h
index f0611bd213502501caaaa868b6e39330a76d0fee..8f0350b529e1cab5cde2e177294b4e088bf89521 100644
--- a/config/examples/Geeetech/A10M/Configuration_adv.h
+++ b/config/examples/Geeetech/A10M/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Geeetech/A20M/Configuration_adv.h b/config/examples/Geeetech/A20M/Configuration_adv.h
index f618e84595c447e1d24d351ff07bf0eb43aa0975..656a020e2773c3766881d32a8dab1d01d35922d5 100644
--- a/config/examples/Geeetech/A20M/Configuration_adv.h
+++ b/config/examples/Geeetech/A20M/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Geeetech/MeCreator2/Configuration_adv.h b/config/examples/Geeetech/MeCreator2/Configuration_adv.h
index 30d3121e15a8f2cee505cf8c908f34ed8d6bc05f..438cc2babb4a879c39011a52eb17f319e49e1ce5 100644
--- a/config/examples/Geeetech/MeCreator2/Configuration_adv.h
+++ b/config/examples/Geeetech/MeCreator2/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2252,7 +2252,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2312,7 +2312,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
index dfc64c2cf8d9450ef19137fd09ae68c2318281fc..072b82c5ad6c990f5736c697335864daaba3d5f2 100644
--- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
+++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
index dfc64c2cf8d9450ef19137fd09ae68c2318281fc..072b82c5ad6c990f5736c697335864daaba3d5f2 100644
--- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
+++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Infitary/i3-M508/Configuration_adv.h b/config/examples/Infitary/i3-M508/Configuration_adv.h
index 18ff0a1fbe24a35aaf3c1b8e0b3678a829db7699..58e91fe49b2e24c2323c66d2ab9d8780500d097a 100644
--- a/config/examples/Infitary/i3-M508/Configuration_adv.h
+++ b/config/examples/Infitary/i3-M508/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/JGAurora/A5/Configuration_adv.h b/config/examples/JGAurora/A5/Configuration_adv.h
index b2a6c44f590212d9738b0ea6a5a1cae8a152d20d..00f80ecea8e194561e6dc25ea86768c19db237ad 100644
--- a/config/examples/JGAurora/A5/Configuration_adv.h
+++ b/config/examples/JGAurora/A5/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2265,7 +2265,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2325,7 +2325,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/MakerParts/Configuration_adv.h b/config/examples/MakerParts/Configuration_adv.h
index 1426f379ae3ff004bb5514cf025867ab7d27cac4..05ee019c6b9e0b12b6e65824342d9c7c3e7cbadd 100644
--- a/config/examples/MakerParts/Configuration_adv.h
+++ b/config/examples/MakerParts/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Malyan/M150/Configuration_adv.h b/config/examples/Malyan/M150/Configuration_adv.h
index 7733dedf080530e3bd2c2893468fc1936041c2d0..4e7489990b70a6df28e41ea1e79cae2092324674 100644
--- a/config/examples/Malyan/M150/Configuration_adv.h
+++ b/config/examples/Malyan/M150/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Malyan/M200/Configuration_adv.h b/config/examples/Malyan/M200/Configuration_adv.h
index 7b342362d32577733630f50ef02eb19de605831f..42116551781b6b01a554b0e6582be1ddddfc1e10 100644
--- a/config/examples/Malyan/M200/Configuration_adv.h
+++ b/config/examples/Malyan/M200/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/config/examples/Micromake/C1/enhanced/Configuration_adv.h
index 54e2ce88ab3d97ea962449e6d84e2f2464cd0e62..bf159cd1fa2ec8a5fb2eb42bf5d76cc144516848 100644
--- a/config/examples/Micromake/C1/enhanced/Configuration_adv.h
+++ b/config/examples/Micromake/C1/enhanced/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Mks/Robin/Configuration_adv.h b/config/examples/Mks/Robin/Configuration_adv.h
index 9fdd481f74463170c2748f2cd909ef090c418d86..6799d0df02dd2edf7e96ce4ec946f27c53859334 100644
--- a/config/examples/Mks/Robin/Configuration_adv.h
+++ b/config/examples/Mks/Robin/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Mks/Sbase/Configuration_adv.h b/config/examples/Mks/Sbase/Configuration_adv.h
index d37f3f8c75822c9f603cf717d186797a150a6d81..4a672e5223bd61a66085f03c194068c1aec36624 100644
--- a/config/examples/Mks/Sbase/Configuration_adv.h
+++ b/config/examples/Mks/Sbase/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2269,7 +2269,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2329,7 +2329,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/RapideLite/RL200/Configuration_adv.h b/config/examples/RapideLite/RL200/Configuration_adv.h
index b58239a594f90372e58328860cd2b48a02acf43b..18a2de5f80262b3f3ac7bf29f81bd7d6e43198d6 100644
--- a/config/examples/RapideLite/RL200/Configuration_adv.h
+++ b/config/examples/RapideLite/RL200/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/RigidBot/Configuration_adv.h b/config/examples/RigidBot/Configuration_adv.h
index 2d0226b7b56fed7f57511f17f6c330513d6996e7..a9858fd38e154cc78a7b3dee2d4dfe9b8ce77602 100644
--- a/config/examples/RigidBot/Configuration_adv.h
+++ b/config/examples/RigidBot/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/SCARA/Configuration_adv.h b/config/examples/SCARA/Configuration_adv.h
index 1eb07393e0f449efece2e50b28812a71a8b4ecbf..b58848792c5b7c022b00f26f23b077803e8482c3 100644
--- a/config/examples/SCARA/Configuration_adv.h
+++ b/config/examples/SCARA/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2265,7 +2265,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2325,7 +2325,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
index 150f06d546d949d10d477cbd226e3e5ae95fbc68..1a978afadee014b62b28d7bf3970c7636df8f175 100644
--- a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
+++ b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2263,7 +2263,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2323,7 +2323,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Sanguinololu/Configuration_adv.h b/config/examples/Sanguinololu/Configuration_adv.h
index e44e5632bbaa1c43a8d53684ec37e4b128608eaf..a5099391f61c9e0dc41890116aa8b7035f4dd803 100644
--- a/config/examples/Sanguinololu/Configuration_adv.h
+++ b/config/examples/Sanguinololu/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/TheBorg/Configuration_adv.h b/config/examples/TheBorg/Configuration_adv.h
index 1501e45bc68e4859d1be21a9a68cd12a5dcddecc..2b69e488cd9716c62566a53feafd03caeffd4ac3 100644
--- a/config/examples/TheBorg/Configuration_adv.h
+++ b/config/examples/TheBorg/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/TinyBoy2/Configuration_adv.h b/config/examples/TinyBoy2/Configuration_adv.h
index 2b095d8953e67381cdf9714907a0ddafda43ab43..95c48add828a782c3201a860d7e7c30f757bf418 100644
--- a/config/examples/TinyBoy2/Configuration_adv.h
+++ b/config/examples/TinyBoy2/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Tronxy/X3A/Configuration_adv.h b/config/examples/Tronxy/X3A/Configuration_adv.h
index a86f37c8590d0d22d236782ba576834c7fdb8d0f..26e74390ed0b7aee8099f31b03fe26ff83585153 100644
--- a/config/examples/Tronxy/X3A/Configuration_adv.h
+++ b/config/examples/Tronxy/X3A/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Tronxy/X5S-2E/Configuration_adv.h b/config/examples/Tronxy/X5S-2E/Configuration_adv.h
index 443264ad1d5d7442045811d6980b2a98a7bddbc6..a876f31eb3b9ea925d43f72a761ddb6b56b037ab 100644
--- a/config/examples/Tronxy/X5S-2E/Configuration_adv.h
+++ b/config/examples/Tronxy/X5S-2E/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/UltiMachine/Archim1/Configuration_adv.h b/config/examples/UltiMachine/Archim1/Configuration_adv.h
index 619927ce24b53992f87dabc2b64fe4f37e1a00c8..8249046bf8e1c74da345d6e351867e89f2084712 100644
--- a/config/examples/UltiMachine/Archim1/Configuration_adv.h
+++ b/config/examples/UltiMachine/Archim1/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/UltiMachine/Archim2/Configuration_adv.h b/config/examples/UltiMachine/Archim2/Configuration_adv.h
index d3e60beca5bdabcec2a6175bb5e96c0f005f72a2..99515bf98fbb24d6993b75e0e6827324a43b4536 100644
--- a/config/examples/UltiMachine/Archim2/Configuration_adv.h
+++ b/config/examples/UltiMachine/Archim2/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/VORONDesign/Configuration_adv.h b/config/examples/VORONDesign/Configuration_adv.h
index 429f06a5794b3b537e471186950cfc1379ee40fb..301c989859c44d87cc80584abcb0c5390c01d048 100644
--- a/config/examples/VORONDesign/Configuration_adv.h
+++ b/config/examples/VORONDesign/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Velleman/K8200/Configuration_adv.h b/config/examples/Velleman/K8200/Configuration_adv.h
index f2d281baaa3495c52411e69089f14ad0a410bf28..3124c5b1cc6f301c3f6da4893f79c23497d02254 100644
--- a/config/examples/Velleman/K8200/Configuration_adv.h
+++ b/config/examples/Velleman/K8200/Configuration_adv.h
@@ -329,7 +329,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2281,7 +2281,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2341,7 +2341,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Velleman/K8400/Configuration_adv.h b/config/examples/Velleman/K8400/Configuration_adv.h
index 2859c0a9390e3f51028e272ee1fd9542861f6032..51938770b57369e085e860ffaea9d3c05e6e4ed0 100644
--- a/config/examples/Velleman/K8400/Configuration_adv.h
+++ b/config/examples/Velleman/K8400/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/WASP/PowerWASP/Configuration_adv.h b/config/examples/WASP/PowerWASP/Configuration_adv.h
index 003638da8a462f6e384464d6502a8541e0f18a29..ff4096699afaa777a3d96db5ca438924bbc253a6 100644
--- a/config/examples/WASP/PowerWASP/Configuration_adv.h
+++ b/config/examples/WASP/PowerWASP/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
index 871140a4623325324591d4857eccb7b5c84b37c4..17b98d56b943a8513b60cea069976d83ebd9442f 100644
--- a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
+++ b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2267,7 +2267,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2327,7 +2327,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h
index fcfa96be0d79c1abbb2666ccb5f8e62b8318410f..12feb146d88da92624f2cef695d468872e393149 100644
--- a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h
+++ b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2267,7 +2267,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2327,7 +2327,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
index 571f9b1bf55557ba6188dd18a1133e8cf1e8cc6b..1e22594afcc1421c753314e3fcaf396046d824fb 100644
--- a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
+++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2267,7 +2267,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2327,7 +2327,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/config/examples/delta/FLSUN/kossel/Configuration_adv.h
index 571f9b1bf55557ba6188dd18a1133e8cf1e8cc6b..1e22594afcc1421c753314e3fcaf396046d824fb 100644
--- a/config/examples/delta/FLSUN/kossel/Configuration_adv.h
+++ b/config/examples/delta/FLSUN/kossel/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2267,7 +2267,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2327,7 +2327,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
index 9f4130d8fde01fe1f657541c5b528bee8a91ac35..e0487a9f9bc48f3fef7c4836ac2f5cafe3eaed01 100644
--- a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
+++ b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2267,7 +2267,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2327,7 +2327,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h
index 9f4130d8fde01fe1f657541c5b528bee8a91ac35..e0487a9f9bc48f3fef7c4836ac2f5cafe3eaed01 100644
--- a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h
+++ b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2267,7 +2267,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2327,7 +2327,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/delta/MKS/SBASE/Configuration_adv.h b/config/examples/delta/MKS/SBASE/Configuration_adv.h
index abe99866d8b6b0199769e04d1fce8a6f141e814d..5db914a78f3ea3945eb09d71ba4326bc541e94d5 100644
--- a/config/examples/delta/MKS/SBASE/Configuration_adv.h
+++ b/config/examples/delta/MKS/SBASE/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2267,7 +2267,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2327,7 +2327,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/delta/Tevo Little Monster/Configuration_adv.h b/config/examples/delta/Tevo Little Monster/Configuration_adv.h
index aa70f283001c8e7067ffdaf290716bb8cba0bfca..9984ccb86aea48d498a8e244f0dd0976087b5c94 100644
--- a/config/examples/delta/Tevo Little Monster/Configuration_adv.h
+++ b/config/examples/delta/Tevo Little Monster/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2255,7 +2255,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2315,7 +2315,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/delta/generic/Configuration_adv.h b/config/examples/delta/generic/Configuration_adv.h
index 9f4130d8fde01fe1f657541c5b528bee8a91ac35..e0487a9f9bc48f3fef7c4836ac2f5cafe3eaed01 100644
--- a/config/examples/delta/generic/Configuration_adv.h
+++ b/config/examples/delta/generic/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2267,7 +2267,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2327,7 +2327,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/delta/kossel_mini/Configuration_adv.h b/config/examples/delta/kossel_mini/Configuration_adv.h
index e3e5491135dd9fb924db7e622f05ed364b9c999c..bf29999ba9a302242cbd6052cc804dbb5fb50651 100644
--- a/config/examples/delta/kossel_mini/Configuration_adv.h
+++ b/config/examples/delta/kossel_mini/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2266,7 +2266,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2326,7 +2326,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/delta/kossel_xl/Configuration_adv.h b/config/examples/delta/kossel_xl/Configuration_adv.h
index 6aeb81f1d6b68674773a5a7b3e024979180b062c..fafbd0bd124a5b0eb481324d2ab50b4e882ef0de 100644
--- a/config/examples/delta/kossel_xl/Configuration_adv.h
+++ b/config/examples/delta/kossel_xl/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2267,7 +2267,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2327,7 +2327,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/config/examples/gCreate/gMax1.5+/Configuration_adv.h
index 2b628de27232a8a33608b737849ab47dc29ea5f7..7e2165e91f3f047d7eebba2108e0a38331960689 100644
--- a/config/examples/gCreate/gMax1.5+/Configuration_adv.h
+++ b/config/examples/gCreate/gMax1.5+/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/makibox/Configuration_adv.h b/config/examples/makibox/Configuration_adv.h
index 66b09c1551788aa339e455b13f98fda3ae787a22..80dc806692ebabf84a9d44e3bd6f8d567e3c23ed 100644
--- a/config/examples/makibox/Configuration_adv.h
+++ b/config/examples/makibox/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/tvrrug/Round2/Configuration_adv.h b/config/examples/tvrrug/Round2/Configuration_adv.h
index 4fb007a0b614cff268f8b7ce776d82e577557344..4f58660ded1378faa7f6294ed32a3e28001c7bad 100644
--- a/config/examples/tvrrug/Round2/Configuration_adv.h
+++ b/config/examples/tvrrug/Round2/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2268,7 +2268,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2328,7 +2328,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**
diff --git a/config/examples/wt150/Configuration_adv.h b/config/examples/wt150/Configuration_adv.h
index 71b1fac4d09317df0e03173decc57ebf0d163a9f..5e2675f4f4ad2a535d29df8c85f7222e6ceb0012 100644
--- a/config/examples/wt150/Configuration_adv.h
+++ b/config/examples/wt150/Configuration_adv.h
@@ -316,7 +316,7 @@
* If left undefined this defaults to F = F_CPU/(2*255*1)
* ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers
* These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
- * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour.
+ * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
*
* USE_OCR2A_AS_TOP [undefined by default]
* Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -2269,7 +2269,7 @@
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
- // disable abort behaviour.
+ // disable abort behavior.
#define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
@@ -2329,7 +2329,7 @@
//#define NANODLP_Z_SYNC
#if ENABLED(NANODLP_Z_SYNC)
//#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
- // Default behaviour is limited to Z axis only.
+ // Default behavior is limited to Z axis only.
#endif
/**