diff --git a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
index 6468fecdbd675c2be9615c3f9521a7dc46efe080..6acdde3da8fc8d2cee7480223c7059323df147ba 100644
--- a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
+++ b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Anet/A6/Configuration_adv.h b/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
index 3c583e99a6eaa09772cc291c00df3d59d59044a4..2634b8c5d94e3de875ff8e2150fd43479819c493 100644
--- a/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Anet/A8/Configuration_adv.h b/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
index a956ed55784ab5aeb81e5304a65df8da0fc09825..ad00302991c6d86c9bd15231e4346ba91c0d5c78 100644
--- a/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h b/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
index 7aab802c5418c9fcebe71690ac9d912a75a973f4..1cc2bdc4ec69c4f983ab9239e04d4cd5d1a8999b 100644
--- a/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
+++ b/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
index feb4e1afe5d91097c497141b6139990e191fe7a1..6269446a6bb850f4d1ecd04e005c4d54f6e11696 100644
--- a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h
index faf55b9b5b1abdfb13e8434745911719ee7e0420..a9e198fc6decad90eb652fcb0651c0fe9db81ade 100644
--- a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h b/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
index 40661a358fea1839a838f9411ea7112474fcdf9f..13abc50004fded24fcfdf6f96e5e3d383b80d6c2 100644
--- a/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
index 9cc2bf8747480f9526de178b9147e473a72d36bf..e900d958966118936af9220ba8b89716ff84e35b 100644
--- a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h b/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
index 40661a358fea1839a838f9411ea7112474fcdf9f..13abc50004fded24fcfdf6f96e5e3d383b80d6c2 100644
--- a/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Cartesio/Configuration_adv.h b/Marlin/src/config/examples/Cartesio/Configuration_adv.h
index d632feba0dc15ca1941f5416168fa391f1b2e7c7..5f1461a1b37162dc468c1a903a450e84489aed13 100644
--- a/Marlin/src/config/examples/Cartesio/Configuration_adv.h
+++ b/Marlin/src/config/examples/Cartesio/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
index 45992cce41eff3d705ebb2683af42468464ca9e3..6e97c0b835f686a505ca39ce94508998ce9a2220 100755
--- a/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
index b8c1b5620f5beb2c8757c35be46a91da87260d0b..b77f7cbbe609f6d685e3bfd00f0df079e338f357 100644
--- a/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h
index 24aa8b1aeadc66922ca2ca2a27cf057677f0c291..4b461a812c0950ec3c0c1cf8f0766b1143c36e19 100644
--- a/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h
index eb9818aeac0f1ca6b271c1d015f182818a60c2d7..efe2a65dcf447edce8e14d9575a74125ccb0177d 100644
--- a/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h b/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h
index e7befc76720619b0eee74306acc17f244a1c1656..00f32b35baa718211816719c01cb5d91c60a7753 100644
--- a/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h b/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
index eb9818aeac0f1ca6b271c1d015f182818a60c2d7..efe2a65dcf447edce8e14d9575a74125ccb0177d 100644
--- a/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Felix/Configuration_adv.h b/Marlin/src/config/examples/Felix/Configuration_adv.h
index 205f9b2be32c373b7fc41f25dfb36671b1bac5ec..55fdd9253c268a3764033f248f9cfe7b30ecf06c 100644
--- a/Marlin/src/config/examples/Felix/Configuration_adv.h
+++ b/Marlin/src/config/examples/Felix/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
index 217676fe436f9989bcfdafa25e2c70e65e89d865..11e3e23e7aef7277d6816880ba275b4a8bcd9b35 100644
--- a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
+++ b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h b/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
index 1f4dfd5f91b047a765bda0a8ae9d76509f424a08..d2c14372bab6f1bc3b6e6745d0ca0b40acfa583b 100644
--- a/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
+++ b/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h b/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
index bc41b990f401856669e1ce2e0528b75f824de7fc..0ee2c9146b50fd89c1449c501ef64c8267dfb123 100644
--- a/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
+++ b/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/MakerParts/Configuration_adv.h b/Marlin/src/config/examples/MakerParts/Configuration_adv.h
index 7aebd01bdaa54e8fb6fa5258fc8ec31f79752a14..c3608c8d5514ec924895e135037d2e8c41f85ef5 100644
--- a/Marlin/src/config/examples/MakerParts/Configuration_adv.h
+++ b/Marlin/src/config/examples/MakerParts/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h b/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
index 7c65ff699017200e6d195aba0287aeaabe493afa..27f5ed9d70774da26b4c4335fe03a5122a1b656d 100644
--- a/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
+++ b/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h b/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
index e55d1d8917f4c1256b7f7e1d9cee9a6a5b7966fa..c9cf0e883aaea6eaec1058edd2d35277f3eaac7e 100644
--- a/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
+++ b/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
index 72917b9141d0c409a04622592545e137883a4de4..d94d77dd053edd0ba44c960f881c5b4a42d7d236 100644
--- a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
+++ b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h b/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
index 484e52cd646984ca699e5c1d719cbeca9567cb2e..08c606f71306665a5349a6fe8dd257270dae9daa 100644
--- a/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
+++ b/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
@@ -754,6 +754,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/RigidBot/Configuration_adv.h b/Marlin/src/config/examples/RigidBot/Configuration_adv.h
index 52c2fafd28ab45a726699ce1722e0ebc08ee7618..b9b8052f6f97d7bec3da9b011ef308c5fd55fb03 100644
--- a/Marlin/src/config/examples/RigidBot/Configuration_adv.h
+++ b/Marlin/src/config/examples/RigidBot/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/SCARA/Configuration_adv.h b/Marlin/src/config/examples/SCARA/Configuration_adv.h
index ed6290d1a2794c146f967dff44c79a707373f982..70c7f35501212864de1230d96e2b45b97af739f8 100644
--- a/Marlin/src/config/examples/SCARA/Configuration_adv.h
+++ b/Marlin/src/config/examples/SCARA/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h b/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
index db8101419212d3976d3027e6e1304db5b5e0e589..1007df1bf6dbf063b53419f65f35cbc320fc116e 100644
--- a/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
+++ b/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/TheBorg/Configuration_adv.h b/Marlin/src/config/examples/TheBorg/Configuration_adv.h
index 6d72365f557a721428f896a4103536d3ebc394ba..fb5d0048a6a41358b325e1a989c4284bb47275b1 100644
--- a/Marlin/src/config/examples/TheBorg/Configuration_adv.h
+++ b/Marlin/src/config/examples/TheBorg/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h b/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
index 932a4d258752ecf7d2abfe5af6658f708421fc08..037d2cfd7cc82cbad64622779ccf047440c0abdd 100644
--- a/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
+++ b/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h
index d387726ecbcfc0b6a0491c62eb2a627fb82fca25..aef9570d1897be5f3b7773a098ef05c68b2ab9e6 100644
--- a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h
+++ b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h b/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h
index da3717be45ce2313b4c1d9c3db18a0f5ca61c34a..890a3fd2674e59990ce24aac094d5793673286ec 100644
--- a/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h
+++ b/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h
@@ -759,6 +759,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h b/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h
index 04ca9efebf123d75aa2c617c0d1bfb00dd7c878a..bd5f2641fbb74cc8df0146fb43078a3cd18234d3 100644
--- a/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h
+++ b/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
index a17c69209343f6c7093c582a6e19c873fd95b4f6..e863cfd8821a30d12137ecc6987786dcc5039760 100644
--- a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h	
+++ b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h	
@@ -748,6 +748,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
index 4fc0e364ec2630afab439be0267cfe0e5fc477c6..bf875efe079f244f19845cef3e5c238b7fbec67c 100644
--- a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
@@ -748,6 +748,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h
index bf4ec5dba1c0ec0330eb5949029aae0276272b26..6c6f18c66dceaeade92e9b995ae8a1d6edabee19 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h
@@ -748,6 +748,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
index eb471b709d449ad3fa86818b1a74384ed6d13e3e..aa14fe39085e1503fa97c01af718bd5f83880fb4 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
@@ -748,6 +748,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/delta/generic/Configuration_adv.h b/Marlin/src/config/examples/delta/generic/Configuration_adv.h
index eb471b709d449ad3fa86818b1a74384ed6d13e3e..aa14fe39085e1503fa97c01af718bd5f83880fb4 100644
--- a/Marlin/src/config/examples/delta/generic/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/generic/Configuration_adv.h
@@ -748,6 +748,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
index eb471b709d449ad3fa86818b1a74384ed6d13e3e..aa14fe39085e1503fa97c01af718bd5f83880fb4 100644
--- a/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
@@ -748,6 +748,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
index ea5c5da504cf6c41163535a033496bcded42c8a7..373b3d453b69f42cf566bd9decb3724d4ed802c1 100644
--- a/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
@@ -753,6 +753,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
index c35d5dfb5694ecdae8b65ec5e2813a9a0d2c22ff..a0a82a177f0a21156c9c5bd3dfa9294de1761003 100644
--- a/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
@@ -748,6 +748,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
index 96f21ce3ca1a1be98d614ffbf6e3c6d1000dffde..810e5857c78ca24473d9d8818229a11c1386eb2f 100644
--- a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
+++ b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/makibox/Configuration_adv.h b/Marlin/src/config/examples/makibox/Configuration_adv.h
index 9db0c555914c3c1c9edb462b85093a8a13f8e1ec..6d1b38c94558fe502f3773f4786a2c3cb41b1dde 100644
--- a/Marlin/src/config/examples/makibox/Configuration_adv.h
+++ b/Marlin/src/config/examples/makibox/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h b/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h
index fc8b2af43f3e34d7aaf38d4d11190808a4b0ed7d..60a28b09bbb3b004f1701691f3383967b382fcad 100644
--- a/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h
+++ b/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/wt150/Configuration_adv.h b/Marlin/src/config/examples/wt150/Configuration_adv.h
index e7ce5cc26e23cb13979f062cc3335681193d036f..f84a0691f5e02201e8cdde0d18bd3cca6523c020 100644
--- a/Marlin/src/config/examples/wt150/Configuration_adv.h
+++ b/Marlin/src/config/examples/wt150/Configuration_adv.h
@@ -747,6 +747,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //