diff --git a/Marlin/SanityCheck.h b/Marlin/SanityCheck.h
index ee67417a1cb064c5a5a2ed886faa7354ecc28a51..e52eea62a299830e963aaf3612707a04dfd8350c 100644
--- a/Marlin/SanityCheck.h
+++ b/Marlin/SanityCheck.h
@@ -96,13 +96,13 @@
*/
#ifdef MESH_BED_LEVELING
#ifdef DELTA
- #error MESH_BED_LEVELING does not yet support DELTA printers
+ #error MESH_BED_LEVELING does not yet support DELTA printers.
#endif
#ifdef ENABLE_AUTO_BED_LEVELING
- #error Select ENABLE_AUTO_BED_LEVELING or MESH_BED_LEVELING, not both
+ #error Select ENABLE_AUTO_BED_LEVELING or MESH_BED_LEVELING, not both.
#endif
#if MESH_NUM_X_POINTS > 7 || MESH_NUM_Y_POINTS > 7
- #error MESH_NUM_X_POINTS and MESH_NUM_Y_POINTS need to be less than 8
+ #error MESH_NUM_X_POINTS and MESH_NUM_Y_POINTS need to be less than 8.
#endif
#endif
@@ -129,23 +129,23 @@
*/
#if defined(Z_PROBE_ENDSTOP)
#ifndef Z_PROBE_PIN
- #error You must have a Z_PROBE_PIN defined in your pins_XXXX.h file if you enable Z_PROBE_ENDSTOP
+ #error You must have a Z_PROBE_PIN defined in your pins_XXXX.h file if you enable Z_PROBE_ENDSTOP.
#endif
#if Z_PROBE_PIN == -1
- #error You must set Z_PROBE_PIN to a valid pin if you enable Z_PROBE_ENDSTOP
+ #error You must set Z_PROBE_PIN to a valid pin if you enable Z_PROBE_ENDSTOP.
#endif
// Forcing Servo definitions can break some hall effect sensor setups. Leaving these here for further comment.
// #ifndef NUM_SERVOS
-// #error You must have NUM_SERVOS defined and there must be at least 1 configured to use Z_PROBE_ENDSTOP
+// #error You must have NUM_SERVOS defined and there must be at least 1 configured to use Z_PROBE_ENDSTOP.
// #endif
// #if defined(NUM_SERVOS) && NUM_SERVOS < 1
-// #error You must have at least 1 servo defined for NUM_SERVOS to use Z_PROBE_ENDSTOP
+// #error You must have at least 1 servo defined for NUM_SERVOS to use Z_PROBE_ENDSTOP.
// #endif
// #ifndef SERVO_ENDSTOPS
-// #error You must have SERVO_ENDSTOPS defined and have the Z index set to at least 0 or above to use Z_PROBE_ENDSTOP
+// #error You must have SERVO_ENDSTOPS defined and have the Z index set to at least 0 or above to use Z_PROBE_ENDSTOP.
// #endif
// #ifndef SERVO_ENDSTOP_ANGLES
-// #error You must have SERVO_ENDSTOP_ANGLES defined for Z Extend and Retract to use Z_PROBE_AND_ENSTOP
+// #error You must have SERVO_ENDSTOP_ANGLES defined for Z Extend and Retract to use Z_PROBE_ENDSTOP.
// #endif
#endif
/**
@@ -176,7 +176,7 @@
#define X_PROBE_ERROR
#endif
#ifdef X_PROBE_ERROR
- #error The X axis probing range is too small to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS
+ #error The X axis probing range is too small to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS.
#endif
#if Y_PROBE_OFFSET_FROM_EXTRUDER < 0
#if PROBE_SIZE_Y <= -PROBE_AREA_DEPTH
@@ -186,7 +186,7 @@
#define Y_PROBE_ERROR
#endif
#ifdef Y_PROBE_ERROR
- #error The Y axis probing range is too small to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS
+ #error The Y axis probing range is too small to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS.
#endif
#undef PROBE_SIZE_X
@@ -272,18 +272,18 @@
*/
#if HAS_AUTO_FAN && HAS_FAN
#if EXTRUDER_0_AUTO_FAN_PIN == FAN_PIN
- #error You cannot set EXTRUDER_0_AUTO_FAN_PIN equal to FAN_PIN
+ #error You cannot set EXTRUDER_0_AUTO_FAN_PIN equal to FAN_PIN.
#elif EXTRUDER_1_AUTO_FAN_PIN == FAN_PIN
- #error You cannot set EXTRUDER_1_AUTO_FAN_PIN equal to FAN_PIN
+ #error You cannot set EXTRUDER_1_AUTO_FAN_PIN equal to FAN_PIN.
#elif EXTRUDER_2_AUTO_FAN_PIN == FAN_PIN
- #error You cannot set EXTRUDER_2_AUTO_FAN_PIN equal to FAN_PIN
+ #error You cannot set EXTRUDER_2_AUTO_FAN_PIN equal to FAN_PIN.
#elif EXTRUDER_3_AUTO_FAN_PIN == FAN_PIN
- #error You cannot set EXTRUDER_3_AUTO_FAN_PIN equal to FAN_PIN
+ #error You cannot set EXTRUDER_3_AUTO_FAN_PIN equal to FAN_PIN.
#endif
#endif
#if HAS_FAN && CONTROLLERFAN_PIN == FAN_PIN
- #error You cannot set CONTROLLERFAN_PIN equal to FAN_PIN
+ #error You cannot set CONTROLLERFAN_PIN equal to FAN_PIN.
#endif
/**
@@ -291,38 +291,38 @@
*/
#if EXTRUDERS > 3
#if !HAS_HEATER_3
- #error HEATER_3_PIN not defined for this board
+ #error HEATER_3_PIN not defined for this board.
#endif
#elif EXTRUDERS > 2
#if !HAS_HEATER_2
- #error HEATER_2_PIN not defined for this board
+ #error HEATER_2_PIN not defined for this board.
#endif
#elif EXTRUDERS > 1 || defined(HEATERS_PARALLEL)
#if !HAS_HEATER_1
- #error HEATER_1_PIN not defined for this board
+ #error HEATER_1_PIN not defined for this board.
#endif
#endif
#if !HAS_HEATER_0
- #error HEATER_0_PIN not defined for this board
+ #error HEATER_0_PIN not defined for this board.
#endif
/**
* Warnings for old configurations
*/
#ifdef X_HOME_RETRACT_MM
- #error [XYZ]_HOME_RETRACT_MM settings have been renamed [XYZ]_HOME_BUMP_MM
+ #error [XYZ]_HOME_RETRACT_MM settings have been renamed [XYZ]_HOME_BUMP_MM.
#endif
#if WATCH_TEMP_PERIOD > 500
- #error WATCH_TEMP_PERIOD now uses seconds instead of milliseconds
+ #error WATCH_TEMP_PERIOD now uses seconds instead of milliseconds.
#endif
#if !defined(THERMAL_PROTECTION_HOTENDS) && (defined(WATCH_TEMP_PERIOD) || defined(THERMAL_PROTECTION_PERIOD))
- #error Thermal Runaway Protection for hotends must now be enabled with THERMAL_PROTECTION_HOTENDS
+ #error Thermal Runaway Protection for hotends must now be enabled with THERMAL_PROTECTION_HOTENDS.
#endif
#if !defined(THERMAL_PROTECTION_BED) && defined(THERMAL_PROTECTION_BED_PERIOD)
- #error Thermal Runaway Protection for the bed must now be enabled with THERMAL_PROTECTION_BED
+ #error Thermal Runaway Protection for the bed must now be enabled with THERMAL_PROTECTION_BED.
#endif
#endif //SANITYCHECK_H