diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index fab4236ba6e30c8627277891982fb465a5fb1c9d..03690b51b5fa8fe2a47b6a0f967501c7ce5e3363 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/default/Configuration_adv.h b/Marlin/src/config/default/Configuration_adv.h
index fab4236ba6e30c8627277891982fb465a5fb1c9d..03690b51b5fa8fe2a47b6a0f967501c7ce5e3363 100644
--- a/Marlin/src/config/default/Configuration_adv.h
+++ b/Marlin/src/config/default/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
index cdd488d8015bd618b5c99f6425fa1c8e6cde3d00..c68f25311f2ef7ddbf019210e39d986fa82a6fe9 100644
--- a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
+++ b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/Anet/A6/Configuration_adv.h b/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
index e6af12e38d755babc037a9550edf0afe290bb2f9..7d77a5109c34cc3609f0cff91b5f8924b104b8ce 100644
--- a/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/Anet/A8/Configuration_adv.h b/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
index 6aed5686dc9a68e71c870d80c0b3b49936095c0c..fe3111f1f6af282385534f81087f1bc4198bb962 100644
--- a/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h b/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
index 0ff3026413292f0bfff56a0c7fd4047dd7298188..f79a4246c2b091bdec320402e20d9af72143175b 100644
--- a/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
+++ b/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
@@ -1000,9 +1000,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1088,9 +1089,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h b/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
index 2fabd2df7a7c8c38112cb6814e51ace44d2307d4..043ac8bd3103b4d3eb083732fc2a30e71e6e9898 100644
--- a/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
index d4ff484ab933a17577ee4aa5284a6ca4570e10af..4d9c7f702c861bc2bbdbdb1dc596b4ce1dca8aab 100644
--- a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h b/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
index 2fabd2df7a7c8c38112cb6814e51ace44d2307d4..043ac8bd3103b4d3eb083732fc2a30e71e6e9898 100644
--- a/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/Cartesio/Configuration_adv.h b/Marlin/src/config/examples/Cartesio/Configuration_adv.h
index 1cf9bb4a8605663adcdc435ae4df94f882f3efc4..4e82c79936e5648724f4a22d2e5ad675726dab7b 100644
--- a/Marlin/src/config/examples/Cartesio/Configuration_adv.h
+++ b/Marlin/src/config/examples/Cartesio/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
index 7ae777b3a6524637a72c1e5097de10d8b8fe2e8a..7048b4a3e0e83d62e23bed2d472d74f890531f00 100755
--- a/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
index 6a6ed75b94eb88ee21a52e58e96a23ee9c7b5ae9..dd3e4afd49fb274bcbaa840c26b9a6f7f315b843 100644
--- a/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1085,6 +1086,16 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
+ /**
+ * Use software SPI for TMC2130.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
+ */
+ //#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
+
/**
* Use Trinamic's ultra quiet stepping mode.
* When disabled, Marlin will use spreadCycle stepping mode.
diff --git a/Marlin/src/config/examples/Creality/Ender/Configuration_adv.h b/Marlin/src/config/examples/Creality/Ender/Configuration_adv.h
index 8672c4aa7d8a251455a92d152bda899dfabb7b0c..d8b6f231abc46d97326a95a63eaa07e2d70f99b4 100644
--- a/Marlin/src/config/examples/Creality/Ender/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/Ender/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1085,6 +1086,16 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
+ /**
+ * Use software SPI for TMC2130.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
+ */
+ //#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
+
/**
* Use Trinamic's ultra quiet stepping mode.
* When disabled, Marlin will use spreadCycle stepping mode.
diff --git a/Marlin/src/config/examples/Felix/Configuration_adv.h b/Marlin/src/config/examples/Felix/Configuration_adv.h
index 19b1a2249c21e27de73188c2c208a58a6aa61456..d71a9f77f6aa312f32b8a7214c4a88edd53cf09d 100644
--- a/Marlin/src/config/examples/Felix/Configuration_adv.h
+++ b/Marlin/src/config/examples/Felix/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
index 43bcd5f32be7d7d2bdea8af853744f190e4190b3..9bd3dae95f0885e7c13381a3c5c545bdac3ebde8 100644
--- a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
+++ b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h b/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
index 055b2516ce88294e8134b2f8e1fc65a02cfbd1de..f3592dc740a85ab4bfd853a4895080997756919b 100644
--- a/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
+++ b/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h b/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
index 0a15d7af523a5e44289d4ec205506a986761a2c7..ad0ede72fa26025a364ef60e75383a0da6169967 100644
--- a/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
+++ b/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1085,6 +1086,16 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
+ /**
+ * Use software SPI for TMC2130.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
+ */
+ //#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
+
/**
* Use Trinamic's ultra quiet stepping mode.
* When disabled, Marlin will use spreadCycle stepping mode.
diff --git a/Marlin/src/config/examples/MakerParts/Configuration_adv.h b/Marlin/src/config/examples/MakerParts/Configuration_adv.h
index 725b5bfc70bca3fd555a7a3a01a839692a7ddaca..96d1cee9902c5e3a689f496d4ef41a4afcf196ef 100644
--- a/Marlin/src/config/examples/MakerParts/Configuration_adv.h
+++ b/Marlin/src/config/examples/MakerParts/Configuration_adv.h
@@ -1000,9 +1000,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1088,9 +1089,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h b/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
index 1e81d6fbb510da78b3d9431688a309253ecdebab..ea8603520e6d7416e9defa68ae002c2c0b5b8776 100644
--- a/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
+++ b/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h b/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
index cf040f5a487aadf68df8cb8a663c1b18a3be83ae..96124faacb425ab356604fa09a243b759a94fa01 100644
--- a/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
+++ b/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
index 92139143cfd871300edcb937ee355de3f347d780..0535470c9250a42af87b740b4629446778373300 100644
--- a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
+++ b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h b/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
index ff9ce83ad639f1b9e1fd8a12cc2a5a1f311e6384..5083e8b811a69e48fa41a726b479877576ea25ad 100644
--- a/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
+++ b/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
@@ -1007,9 +1007,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1095,9 +1096,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/RigidBot/Configuration_adv.h b/Marlin/src/config/examples/RigidBot/Configuration_adv.h
index cc692d35f4e0a77b399bde0c5d9f80b82cece0aa..24855847d903762d3e7ca862e6a0edf29be5f005 100644
--- a/Marlin/src/config/examples/RigidBot/Configuration_adv.h
+++ b/Marlin/src/config/examples/RigidBot/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/SCARA/Configuration_adv.h b/Marlin/src/config/examples/SCARA/Configuration_adv.h
index 49f2d1ee68b9b4116898addd0fdf9a8eb3702865..39b1dda88f614b0177e92c65b1f491a8a206926a 100644
--- a/Marlin/src/config/examples/SCARA/Configuration_adv.h
+++ b/Marlin/src/config/examples/SCARA/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h b/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
index c4246e8c79de201a7638d259b5f7512df773c91a..64cde0b4bdc25c3884d85976eb0a872bbd5d1e27 100644
--- a/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
+++ b/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/TheBorg/Configuration_adv.h b/Marlin/src/config/examples/TheBorg/Configuration_adv.h
index 0777756e09f7c6e6f2fbd6579d0fc1ab16dab3e0..7b195b47a6d0d527012bc3fe5d94b7e7eb7663a4 100644
--- a/Marlin/src/config/examples/TheBorg/Configuration_adv.h
+++ b/Marlin/src/config/examples/TheBorg/Configuration_adv.h
@@ -996,9 +996,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1082,6 +1083,16 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
+ /**
+ * Use software SPI for TMC2130.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
+ */
+ //#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
+
/**
* Use Trinamic's ultra quiet stepping mode.
* When disabled, Marlin will use spreadCycle stepping mode.
diff --git a/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h b/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
index 39c18e22a63b03e253b13a8a7831004faf606da2..f96f1d9bc2ce055f542aa94f38a24c028e016cb3 100644
--- a/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
+++ b/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h
index 6b7efc454c2a8f18240d1f3bff2b45239fe75847..879ab4a326e541e541f7a49c652bd286ac311b0f 100644
--- a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h
+++ b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h b/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h
index 19fcde8dad72fd8117f753d3c82a3333f7b4515f..5a9de6070be0fd75206a0dbeed3c29e27479d39e 100644
--- a/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h
+++ b/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h
@@ -1012,9 +1012,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1100,9 +1101,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h b/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h
index 53c72e484921245f942220339aeef44a180849e6..ac79e75a12e82791a61de0fff845be710a4aa10c 100644
--- a/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h
+++ b/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
index ffc2a6ef80155b15150a032f2507d6f6ed65550b..e2991376c21d46ab36a6a475c261069080757444 100644
--- a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
+++ b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
@@ -1001,9 +1001,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1089,9 +1090,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
index 59e62b6d1de7a311488f9fcc37930190c50f46ff..f1d706244806060c125d8c67512dc2e5a5a67079 100644
--- a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
@@ -1001,9 +1001,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1089,9 +1090,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h
index 03fd74743752503509ec4f2f53f03f62fb6adbcd..8f111531b52069a5c8bb1f21a0932cf907e4c0c0 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h
@@ -1001,9 +1001,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,6 +1088,16 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
+ /**
+ * Use software SPI for TMC2130.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
+ */
+ //#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
+
/**
* Use Trinamic's ultra quiet stepping mode.
* When disabled, Marlin will use spreadCycle stepping mode.
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
index 8b632a9882ca84b07d09854cb9b15d9dd37bb890..941036748b439648fb4176e9b9f9497d869e74e5 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
@@ -1001,9 +1001,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1089,9 +1090,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/delta/generic/Configuration_adv.h b/Marlin/src/config/examples/delta/generic/Configuration_adv.h
index 8b632a9882ca84b07d09854cb9b15d9dd37bb890..941036748b439648fb4176e9b9f9497d869e74e5 100644
--- a/Marlin/src/config/examples/delta/generic/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/generic/Configuration_adv.h
@@ -1001,9 +1001,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1089,9 +1090,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
index 8b632a9882ca84b07d09854cb9b15d9dd37bb890..941036748b439648fb4176e9b9f9497d869e74e5 100644
--- a/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
@@ -1001,9 +1001,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1089,9 +1090,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
index ed8af1ea49acd5abf06bd1658b7e6294fe08d445..f7b4e535d063eb1c7cff0b744e0ac2eb505c41a9 100644
--- a/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
@@ -1006,9 +1006,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1094,9 +1095,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
index 35f6a5fb249ae3254bd1205f9ef7638ab9782906..bff637b55b881c11fb3e5299ed6d03dc41add57a 100644
--- a/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
@@ -1001,9 +1001,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1089,9 +1090,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
index ae221c3d1e97edc89baa4240a228b7c17f269580..f5de9dca163dee45ecf687edda2b59c191cfc4de 100644
--- a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
+++ b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/makibox/Configuration_adv.h b/Marlin/src/config/examples/makibox/Configuration_adv.h
index 814112cf96daa7b929dd91c53c8cf6446398c139..345b812324a844a21ae912b5a17e2861a033a281 100644
--- a/Marlin/src/config/examples/makibox/Configuration_adv.h
+++ b/Marlin/src/config/examples/makibox/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h b/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h
index 0f1e7f74845233687e39d62cf8595a9d34930514..37144c3343f1792108916d464e79053c35c2017a 100644
--- a/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h
+++ b/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h
@@ -999,9 +999,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1087,9 +1088,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.
diff --git a/Marlin/src/config/examples/wt150/Configuration_adv.h b/Marlin/src/config/examples/wt150/Configuration_adv.h
index c4d0f7ec645da6d1f16bb1d56dfe7fee069c9684..5471455498d9ba967b5d13b37bea6be9330db214 100644
--- a/Marlin/src/config/examples/wt150/Configuration_adv.h
+++ b/Marlin/src/config/examples/wt150/Configuration_adv.h
@@ -1000,9 +1000,10 @@
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
- * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
*/
//#define HAVE_TMC2130
@@ -1088,9 +1089,13 @@
/**
* Use software SPI for TMC2130.
- * SW SPI pins are defined the respective pins files.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
*/
//#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
/**
* Use Trinamic's ultra quiet stepping mode.