diff --git a/.travis.yml b/.travis.yml
new file mode 100644
index 0000000000000000000000000000000000000000..c646ff0805c8db5ac4711a380219e5ad69edd630
--- /dev/null
+++ b/.travis.yml
@@ -0,0 +1,14 @@
+---
+language: c
+
+before_install:
+ - sudo add-apt-repository -y ppa:ubuntu-toolchain-r/test
+ - sudo apt-get update -qq
+install:
+ - sudo apt-get install -qq gcc-avr binutils-avr avr-libc gcc-4.8 g++-4.8 arduino
+ - sudo update-alternatives --install /usr/bin/gcc gcc /usr/bin/gcc-4.8 90
+ - sudo update-alternatives --install /usr/bin/g++ g++ /usr/bin/g++-4.8 90
+ - gcc --version
+ - g++ --version
+
+script: "cd Marlin && make HARDWARE_MOTHERBOARD=70 ARDUINO_INSTALL_DIR=/usr/share/arduino"
diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index d2aba196d9ec6ec058c28bb53e5e7637e96a5271..2702024e568655cf45a2376549c1caa72bcff167 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -777,7 +777,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
* 301 - Rambo - uses Analog input 3
* Note may require analog pins to be defined for different motherboards
**********************************************************************/
-#define FILAMENT_SENSOR
+// Uncomment below to enable
+//#define FILAMENT_SENSOR
+
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 6398f4161b49835eac1ddda043774f54f55d7db4..bce45851dfcb247101d12963dbfa3cdfc28e3e25 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -219,9 +219,11 @@
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
#define AXIS_RELATIVE_MODES {false, false, false, false}
-
+#ifdef CONFIG_STEPPERS_TOSHIBA
+#define MAX_STEP_FREQUENCY 10000 // Max step frequency for Toshiba Stepper Controllers
+#else
#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)
-
+#endif
//By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
#define INVERT_X_STEP_PIN false
#define INVERT_Y_STEP_PIN false
diff --git a/Marlin/DOGMbitmaps.h b/Marlin/DOGMbitmaps.h
index 984f421c0a32fe449bca9dc655a3f97625b48934..d4b8659a0a7de6d68a8d5b76b1999b1b33d4dafe 100644
--- a/Marlin/DOGMbitmaps.h
+++ b/Marlin/DOGMbitmaps.h
@@ -68,54 +68,162 @@ const unsigned char start_bmp[574] PROGMEM = { //AVR-GCC, WinAVR
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xF0
};
-#define STATUS_SCREENWIDTH 115 //Width in pixels
-#define STATUS_SCREENHEIGHT 19 //Height in pixels
-#define STATUS_SCREENBYTEWIDTH 15 //Width in bytes
-const unsigned char status_screen0_bmp[] PROGMEM = { //AVR-GCC, WinAVR
-0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0xFF,0xE0,
-0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
-0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x63,0x0C,0x60,
-0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x47,0x0E,0x20,
-0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x4F,0x0F,0x20,
-0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x5F,0x0F,0xA0,
-0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x5E,0x07,0xA0,
-0x7F,0x80,0x00,0x3F,0xC0,0x00,0x3F,0xC0,0x00,0x41,0x04,0x00,0x40,0x60,0x20,
-0xFB,0xC0,0x00,0x79,0xE0,0x00,0x79,0xE0,0x00,0x20,0x82,0x00,0x40,0xF0,0x20,
-0xF3,0xC0,0x00,0x76,0xE0,0x00,0x76,0xE0,0x00,0x20,0x82,0x00,0x40,0xF0,0x20,
-0xEB,0xC0,0x00,0x7E,0xE0,0x00,0x7E,0xE0,0x00,0x41,0x04,0x00,0x40,0x60,0x20,
-0x7B,0x80,0x00,0x3D,0xC0,0x00,0x39,0xC0,0x00,0x82,0x08,0x00,0x5E,0x07,0xA0,
-0x7B,0x80,0x00,0x3B,0xC0,0x00,0x3E,0xC0,0x01,0x04,0x10,0x00,0x5F,0x0F,0xA0,
-0xFB,0xC0,0x00,0x77,0xE0,0x00,0x76,0xE0,0x01,0x04,0x10,0x00,0x4F,0x0F,0x20,
-0xFB,0xC0,0x00,0x70,0xE0,0x00,0x79,0xE0,0x00,0x82,0x08,0x00,0x47,0x0E,0x20,
-0xFF,0xC0,0x00,0x7F,0xE0,0x00,0x7F,0xE0,0x00,0x41,0x04,0x00,0x63,0x0C,0x60,
-0x3F,0x00,0x00,0x1F,0x80,0x00,0x1F,0x80,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
-0x1E,0x00,0x00,0x0F,0x00,0x00,0x0F,0x00,0x01,0xFF,0xFF,0x80,0x7F,0xFF,0xE0,
-0x0C,0x00,0x00,0x06,0x00,0x00,0x06,0x00,0x01,0xFF,0xFF,0x80,0x00,0x00,0x00
-};
+// Here comes a compile-time operation to match the extruder symbols
+// on the info screen to the set number of extruders in configuration.h
+//
+// When only one extruder is selected, the "1" on the symbol will not
+// be displayed.
-#define STATUS_SCREENWIDTH 115 //Width in pixels
-#define STATUS_SCREENHEIGHT 19 //Height in pixels
-#define STATUS_SCREENBYTEWIDTH 15 //Width in bytes
-const unsigned char status_screen1_bmp[] PROGMEM = { //AVR-GCC, WinAVR
-0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0xFF,0xE0,
-0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
-0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x61,0xF8,0x60,
-0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x41,0xF8,0x20,
-0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0xF0,0x20,
-0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0x60,0x20,
-0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x58,0x01,0xA0,
-0x7F,0x80,0x00,0x3F,0xC0,0x00,0x3F,0xC0,0x00,0x41,0x04,0x00,0x5C,0x63,0xA0,
-0xFB,0xC0,0x00,0x79,0xE0,0x00,0x79,0xE0,0x00,0x20,0x82,0x00,0x5E,0xF7,0xA0,
-0xF3,0xC0,0x00,0x76,0xE0,0x00,0x76,0xE0,0x00,0x20,0x82,0x00,0x5E,0xF7,0xA0,
-0xEB,0xC0,0x00,0x7E,0xE0,0x00,0x7E,0xE0,0x00,0x41,0x04,0x00,0x5C,0x63,0xA0,
-0x7B,0x80,0x00,0x3D,0xC0,0x00,0x39,0xC0,0x00,0x82,0x08,0x00,0x58,0x01,0xA0,
-0x7B,0x80,0x00,0x3B,0xC0,0x00,0x3E,0xC0,0x01,0x04,0x10,0x00,0x40,0x60,0x20,
-0xFB,0xC0,0x00,0x77,0xE0,0x00,0x76,0xE0,0x01,0x04,0x10,0x00,0x40,0xF0,0x20,
-0xFB,0xC0,0x00,0x70,0xE0,0x00,0x79,0xE0,0x00,0x82,0x08,0x00,0x41,0xF8,0x20,
-0xFF,0xC0,0x00,0x7F,0xE0,0x00,0x7F,0xE0,0x00,0x41,0x04,0x00,0x61,0xF8,0x60,
-0x3F,0x00,0x00,0x1F,0x80,0x00,0x1F,0x80,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
-0x1E,0x00,0x00,0x0F,0x00,0x00,0x0F,0x00,0x01,0xFF,0xFF,0x80,0x7F,0xFF,0xE0,
-0x0C,0x00,0x00,0x06,0x00,0x00,0x06,0x00,0x01,0xFF,0xFF,0x80,0x00,0x00,0x00
-};
+#if EXTRUDERS == 1
+ #define STATUS_SCREENWIDTH 115 //Width in pixels
+ #define STATUS_SCREENHEIGHT 19 //Height in pixels
+ #define STATUS_SCREENBYTEWIDTH 15 //Width in bytes
+ const unsigned char status_screen0_bmp[] PROGMEM = { //AVR-GCC, WinAVR
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0xFF,0xE0,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x63,0x0C,0x60,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x47,0x0E,0x20,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x4F,0x0F,0x20,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x5F,0x0F,0xA0,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x5E,0x07,0xA0,
+ 0x7F,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x40,0x60,0x20,
+ 0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x82,0x00,0x40,0xF0,0x20,
+ 0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x82,0x00,0x40,0xF0,0x20,
+ 0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x40,0x60,0x20,
+ 0x7F,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x82,0x08,0x00,0x5E,0x07,0xA0,
+ 0x7F,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x04,0x10,0x00,0x5F,0x0F,0xA0,
+ 0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x04,0x10,0x00,0x4F,0x0F,0x20,
+ 0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x82,0x08,0x00,0x47,0x0E,0x20,
+ 0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x63,0x0C,0x60,
+ 0x3F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
+ 0x1E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0xFF,0xFF,0x80,0x7F,0xFF,0xE0,
+ 0x0C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0xFF,0xFF,0x80,0x00,0x00,0x00
+ };
+
+ #define STATUS_SCREENWIDTH 115 //Width in pixels
+ #define STATUS_SCREENHEIGHT 19 //Height in pixels
+ #define STATUS_SCREENBYTEWIDTH 15 //Width in bytes
+ const unsigned char status_screen1_bmp[] PROGMEM = { //AVR-GCC, WinAVR
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0xFF,0xE0,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x61,0xF8,0x60,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x41,0xF8,0x20,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0xF0,0x20,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0x60,0x20,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x58,0x01,0xA0,
+ 0x7F,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x5C,0x63,0xA0,
+ 0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x82,0x00,0x5E,0xF7,0xA0,
+ 0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x82,0x00,0x5E,0xF7,0xA0,
+ 0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x5C,0x63,0xA0,
+ 0x7F,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x82,0x08,0x00,0x58,0x01,0xA0,
+ 0x7F,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x04,0x10,0x00,0x40,0x60,0x20,
+ 0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x04,0x10,0x00,0x40,0xF0,0x20,
+ 0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x82,0x08,0x00,0x41,0xF8,0x20,
+ 0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x61,0xF8,0x60,
+ 0x3F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
+ 0x1E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0xFF,0xFF,0x80,0x7F,0xFF,0xE0,
+ 0x0C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0xFF,0xFF,0x80,0x00,0x00,0x00
+ };
+#elif EXTRUDERS == 2
+ #define STATUS_SCREENWIDTH 115 //Width in pixels
+ #define STATUS_SCREENHEIGHT 19 //Height in pixels
+ #define STATUS_SCREENBYTEWIDTH 15 //Width in bytes
+ const unsigned char status_screen0_bmp[] PROGMEM = { //AVR-GCC, WinAVR
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0xFF,0xE0,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x63,0x0C,0x60,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x47,0x0E,0x20,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x4F,0x0F,0x20,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x5F,0x0F,0xA0,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x5E,0x07,0xA0,
+ 0x7F,0x80,0x00,0x3F,0xC0,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x40,0x60,0x20,
+ 0xFB,0xC0,0x00,0x79,0xE0,0x00,0x00,0x00,0x00,0x20,0x82,0x00,0x40,0xF0,0x20,
+ 0xF3,0xC0,0x00,0x76,0xE0,0x00,0x00,0x00,0x00,0x20,0x82,0x00,0x40,0xF0,0x20,
+ 0xEB,0xC0,0x00,0x7E,0xE0,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x40,0x60,0x20,
+ 0x7B,0x80,0x00,0x3D,0xC0,0x00,0x00,0x00,0x00,0x82,0x08,0x00,0x5E,0x07,0xA0,
+ 0x7B,0x80,0x00,0x3B,0xC0,0x00,0x00,0x00,0x01,0x04,0x10,0x00,0x5F,0x0F,0xA0,
+ 0xFB,0xC0,0x00,0x77,0xE0,0x00,0x00,0x00,0x01,0x04,0x10,0x00,0x4F,0x0F,0x20,
+ 0xFB,0xC0,0x00,0x70,0xE0,0x00,0x00,0x00,0x00,0x82,0x08,0x00,0x47,0x0E,0x20,
+ 0xFF,0xC0,0x00,0x7F,0xE0,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x63,0x0C,0x60,
+ 0x3F,0x00,0x00,0x1F,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
+ 0x1E,0x00,0x00,0x0F,0x00,0x00,0x00,0x00,0x01,0xFF,0xFF,0x80,0x7F,0xFF,0xE0,
+ 0x0C,0x00,0x00,0x06,0x00,0x00,0x00,0x00,0x01,0xFF,0xFF,0x80,0x00,0x00,0x00
+ };
+
+ #define STATUS_SCREENWIDTH 115 //Width in pixels
+ #define STATUS_SCREENHEIGHT 19 //Height in pixels
+ #define STATUS_SCREENBYTEWIDTH 15 //Width in bytes
+ const unsigned char status_screen1_bmp[] PROGMEM = { //AVR-GCC, WinAVR
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0xFF,0xE0,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x61,0xF8,0x60,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x41,0xF8,0x20,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0xF0,0x20,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0x60,0x20,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x58,0x01,0xA0,
+ 0x7F,0x80,0x00,0x3F,0xC0,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x5C,0x63,0xA0,
+ 0xFB,0xC0,0x00,0x79,0xE0,0x00,0x00,0x00,0x00,0x20,0x82,0x00,0x5E,0xF7,0xA0,
+ 0xF3,0xC0,0x00,0x76,0xE0,0x00,0x00,0x00,0x00,0x20,0x82,0x00,0x5E,0xF7,0xA0,
+ 0xEB,0xC0,0x00,0x7E,0xE0,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x5C,0x63,0xA0,
+ 0x7B,0x80,0x00,0x3D,0xC0,0x00,0x00,0x00,0x00,0x82,0x08,0x00,0x58,0x01,0xA0,
+ 0x7B,0x80,0x00,0x3B,0xC0,0x00,0x00,0x00,0x01,0x04,0x10,0x00,0x40,0x60,0x20,
+ 0xFB,0xC0,0x00,0x77,0xE0,0x00,0x00,0x00,0x01,0x04,0x10,0x00,0x40,0xF0,0x20,
+ 0xFB,0xC0,0x00,0x70,0xE0,0x00,0x00,0x00,0x00,0x82,0x08,0x00,0x41,0xF8,0x20,
+ 0xFF,0xC0,0x00,0x7F,0xE0,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x61,0xF8,0x60,
+ 0x3F,0x00,0x00,0x1F,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
+ 0x1E,0x00,0x00,0x0F,0x00,0x00,0x00,0x00,0x01,0xFF,0xFF,0x80,0x7F,0xFF,0xE0,
+ 0x0C,0x00,0x00,0x06,0x00,0x00,0x00,0x00,0x01,0xFF,0xFF,0x80,0x00,0x00,0x00
+ };
+#else
+ #define STATUS_SCREENWIDTH 115 //Width in pixels
+ #define STATUS_SCREENHEIGHT 19 //Height in pixels
+ #define STATUS_SCREENBYTEWIDTH 15 //Width in bytes
+ const unsigned char status_screen0_bmp[] PROGMEM = { //AVR-GCC, WinAVR
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0xFF,0xE0,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x63,0x0C,0x60,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x47,0x0E,0x20,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x4F,0x0F,0x20,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x5F,0x0F,0xA0,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x5E,0x07,0xA0,
+ 0x7F,0x80,0x00,0x3F,0xC0,0x00,0x3F,0xC0,0x00,0x41,0x04,0x00,0x40,0x60,0x20,
+ 0xFB,0xC0,0x00,0x79,0xE0,0x00,0x79,0xE0,0x00,0x20,0x82,0x00,0x40,0xF0,0x20,
+ 0xF3,0xC0,0x00,0x76,0xE0,0x00,0x76,0xE0,0x00,0x20,0x82,0x00,0x40,0xF0,0x20,
+ 0xEB,0xC0,0x00,0x7E,0xE0,0x00,0x7E,0xE0,0x00,0x41,0x04,0x00,0x40,0x60,0x20,
+ 0x7B,0x80,0x00,0x3D,0xC0,0x00,0x39,0xC0,0x00,0x82,0x08,0x00,0x5E,0x07,0xA0,
+ 0x7B,0x80,0x00,0x3B,0xC0,0x00,0x3E,0xC0,0x01,0x04,0x10,0x00,0x5F,0x0F,0xA0,
+ 0xFB,0xC0,0x00,0x77,0xE0,0x00,0x76,0xE0,0x01,0x04,0x10,0x00,0x4F,0x0F,0x20,
+ 0xFB,0xC0,0x00,0x70,0xE0,0x00,0x79,0xE0,0x00,0x82,0x08,0x00,0x47,0x0E,0x20,
+ 0xFF,0xC0,0x00,0x7F,0xE0,0x00,0x7F,0xE0,0x00,0x41,0x04,0x00,0x63,0x0C,0x60,
+ 0x3F,0x00,0x00,0x1F,0x80,0x00,0x1F,0x80,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
+ 0x1E,0x00,0x00,0x0F,0x00,0x00,0x0F,0x00,0x01,0xFF,0xFF,0x80,0x7F,0xFF,0xE0,
+ 0x0C,0x00,0x00,0x06,0x00,0x00,0x06,0x00,0x01,0xFF,0xFF,0x80,0x00,0x00,0x00
+ };
+
+ #define STATUS_SCREENWIDTH 115 //Width in pixels
+ #define STATUS_SCREENHEIGHT 19 //Height in pixels
+ #define STATUS_SCREENBYTEWIDTH 15 //Width in bytes
+ const unsigned char status_screen1_bmp[] PROGMEM = { //AVR-GCC, WinAVR
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0xFF,0xE0,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x61,0xF8,0x60,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x41,0xF8,0x20,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0xF0,0x20,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0x60,0x20,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x58,0x01,0xA0,
+ 0x7F,0x80,0x00,0x3F,0xC0,0x00,0x3F,0xC0,0x00,0x41,0x04,0x00,0x5C,0x63,0xA0,
+ 0xFB,0xC0,0x00,0x79,0xE0,0x00,0x79,0xE0,0x00,0x20,0x82,0x00,0x5E,0xF7,0xA0,
+ 0xF3,0xC0,0x00,0x76,0xE0,0x00,0x76,0xE0,0x00,0x20,0x82,0x00,0x5E,0xF7,0xA0,
+ 0xEB,0xC0,0x00,0x7E,0xE0,0x00,0x7E,0xE0,0x00,0x41,0x04,0x00,0x5C,0x63,0xA0,
+ 0x7B,0x80,0x00,0x3D,0xC0,0x00,0x39,0xC0,0x00,0x82,0x08,0x00,0x58,0x01,0xA0,
+ 0x7B,0x80,0x00,0x3B,0xC0,0x00,0x3E,0xC0,0x01,0x04,0x10,0x00,0x40,0x60,0x20,
+ 0xFB,0xC0,0x00,0x77,0xE0,0x00,0x76,0xE0,0x01,0x04,0x10,0x00,0x40,0xF0,0x20,
+ 0xFB,0xC0,0x00,0x70,0xE0,0x00,0x79,0xE0,0x00,0x82,0x08,0x00,0x41,0xF8,0x20,
+ 0xFF,0xC0,0x00,0x7F,0xE0,0x00,0x7F,0xE0,0x00,0x41,0x04,0x00,0x61,0xF8,0x60,
+ 0x3F,0x00,0x00,0x1F,0x80,0x00,0x1F,0x80,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
+ 0x1E,0x00,0x00,0x0F,0x00,0x00,0x0F,0x00,0x01,0xFF,0xFF,0x80,0x7F,0xFF,0xE0,
+ 0x0C,0x00,0x00,0x06,0x00,0x00,0x06,0x00,0x01,0xFF,0xFF,0x80,0x00,0x00,0x00
+ };
+#endif // Extruders
diff --git a/Marlin/Marlin_main.cpp b/Marlin/Marlin_main.cpp
index 3bd8e317898bc7b8c52ecb65dfa0b0955c00205a..e8d800eb484a36d5b4666335fdc600fe3117f6bd 100644
--- a/Marlin/Marlin_main.cpp
+++ b/Marlin/Marlin_main.cpp
@@ -1385,7 +1385,7 @@ void process_commands()
st_synchronize();
codenum += millis(); // keep track of when we started waiting
previous_millis_cmd = millis();
- while(millis() < codenum ){
+ while(millis() < codenum) {
manage_heater();
manage_inactivity();
lcd_update();
@@ -1413,7 +1413,6 @@ void process_commands()
plan_bed_level_matrix.set_to_identity(); //Reset the plane ("erase" all leveling data)
#endif //ENABLE_AUTO_BED_LEVELING
-
saved_feedrate = feedrate;
saved_feedmultiply = feedmultiply;
feedmultiply = 100;
@@ -1863,20 +1862,39 @@ void process_commands()
case 0: // M0 - Unconditional stop - Wait for user button press on LCD
case 1: // M1 - Conditional stop - Wait for user button press on LCD
{
- LCD_MESSAGEPGM(MSG_USERWAIT);
+ char *src = strchr_pointer + 2;
+
codenum = 0;
- if(code_seen('P')) codenum = code_value(); // milliseconds to wait
- if(code_seen('S')) codenum = code_value() * 1000; // seconds to wait
+ bool hasP = false, hasS = false;
+ if (code_seen('P')) {
+ codenum = code_value(); // milliseconds to wait
+ hasP = codenum > 0;
+ }
+ if (code_seen('S')) {
+ codenum = code_value() * 1000; // seconds to wait
+ hasS = codenum > 0;
+ }
+ starpos = strchr(src, '*');
+ if (starpos != NULL) *(starpos) = '\0';
+ while (*src == ' ') ++src;
+ if (!hasP && !hasS && *src != '\0') {
+ lcd_setstatus(src);
+ } else {
+ LCD_MESSAGEPGM(MSG_USERWAIT);
+ }
+
+ lcd_ignore_click();
st_synchronize();
previous_millis_cmd = millis();
if (codenum > 0){
codenum += millis(); // keep track of when we started waiting
- while(millis() < codenum && !lcd_clicked()){
+ while(millis() < codenum && !lcd_clicked()){
manage_heater();
manage_inactivity();
lcd_update();
}
+ lcd_ignore_click(false);
}else{
if (!lcd_detected())
break;
@@ -1886,7 +1904,10 @@ void process_commands()
lcd_update();
}
}
- LCD_MESSAGEPGM(MSG_RESUMING);
+ if (IS_SD_PRINTING)
+ LCD_MESSAGEPGM(MSG_RESUMING);
+ else
+ LCD_MESSAGEPGM(WELCOME_MSG);
}
break;
#endif
diff --git a/Marlin/dogm_lcd_implementation.h b/Marlin/dogm_lcd_implementation.h
index 8d450cb37098e8ccb38f998dcf6390742576501a..d0570c99c367ff20e29358e356663b64d2fcb854 100644
--- a/Marlin/dogm_lcd_implementation.h
+++ b/Marlin/dogm_lcd_implementation.h
@@ -245,9 +245,6 @@ static void lcd_implementation_status_screen()
u8g.drawBox(38,17,2,2);
u8g.setColorIndex(1); // black on white
}
- #else
- u8g.setPrintPos(31,27);
- u8g.print("---");
#endif
// Extruder 3
@@ -266,9 +263,6 @@ static void lcd_implementation_status_screen()
u8g.drawBox(62,17,2,2);
u8g.setColorIndex(1); // black on white
}
- #else
- u8g.setPrintPos(55,27);
- u8g.print("---");
#endif
// Heatbed
diff --git a/Marlin/example_configurations/delta/Configuration.h b/Marlin/example_configurations/delta/Configuration.h
index 975e52efd2af43fd6db433417bbaaf60f8f31936..042b221c3275887e7fcd708829b7fa72c5bf1f4d 100644
--- a/Marlin/example_configurations/delta/Configuration.h
+++ b/Marlin/example_configurations/delta/Configuration.h
@@ -41,6 +41,7 @@
// 33 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed)
// 34 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed)
// 35 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan)
+// 36 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Fan)
// 4 = Duemilanove w/ ATMega328P pin assignment
// 5 = Gen6
// 51 = Gen6 deluxe
@@ -54,12 +55,14 @@
// 68 = Azteeg X3 Pro
// 7 = Ultimaker
// 71 = Ultimaker (Older electronics. Pre 1.5.4. This is rare)
+// 72 = Ultimainboard 2.x (Uses TEMP_SENSOR 20)
// 77 = 3Drag Controller
// 8 = Teensylu
// 80 = Rumba
// 81 = Printrboard (AT90USB1286)
// 82 = Brainwave (AT90USB646)
// 83 = SAV Mk-I (AT90USB1286)
+// 84 = Teensy++2.0 (AT90USB1286) // CLI compile: DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84 make
// 9 = Gen3+
// 70 = Megatronics
// 701= Megatronics v2.0
@@ -68,6 +71,8 @@
// 91 = Final OMCA board
// 301= Rambo
// 21 = Elefu Ra Board (v3)
+// 88 = 5DPrint D8 Driver Board
+// 999 = Leapfrog
#ifndef MOTHERBOARD
#define MOTHERBOARD 33
@@ -141,7 +146,11 @@
// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
// 10 is 100k RS thermistor 198-961 (4.7k pullup)
-// 60 is 100k Maker's Tool Works Kapton Bed Thermistor
+// 11 is 100k beta 3950 1% thermistor (4.7k pullup)
+// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
+// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
+// 20 is the PT100 circuit found in the Ultimainboard V2.x
+// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
//
// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
// (but gives greater accuracy and more stable PID)
@@ -205,7 +214,7 @@
// is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
#define PID_INTEGRAL_DRIVE_MAX 255 //limit for the integral term
#define K1 0.95 //smoothing factor within the PID
- #define PID_dT ((16.0 * 8.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
+ #define PID_dT ((OVERSAMPLENR * 10.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
// Ultimaker
@@ -271,6 +280,44 @@
#define EXTRUDE_MINTEMP 170
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
+/*================== Thermal Runaway Protection ==============================
+This is a feature to protect your printer from burn up in flames if it has
+a thermistor coming off place (this happened to a friend of mine recently and
+motivated me writing this feature).
+
+The issue: If a thermistor come off, it will read a lower temperature than actual.
+The system will turn the heater on forever, burning up the filament and anything
+else around.
+
+After the temperature reaches the target for the first time, this feature will
+start measuring for how long the current temperature stays below the target
+minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS).
+
+If it stays longer than _PERIOD, it means the thermistor temperature
+cannot catch up with the target, so something *may be* wrong. Then, to be on the
+safe side, the system will he halt.
+
+Bear in mind the count down will just start AFTER the first time the
+thermistor temperature is over the target, so you will have no problem if
+your extruder heater takes 2 minutes to hit the target on heating.
+
+*/
+// If you want to enable this feature for all your extruder heaters,
+// uncomment the 2 defines below:
+
+// Parameters for all extruder heaters
+//#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds
+//#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
+
+// If you want to enable this feature for your bed heater,
+// uncomment the 2 defines below:
+
+// Parameters for the bed heater
+//#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds
+//#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
+//===========================================================================
+
+
//===========================================================================
//=============================Mechanical Settings===========================
//===========================================================================
@@ -326,6 +373,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
#define DISABLE_Y false
#define DISABLE_Z false
#define DISABLE_E false // For all extruders
+#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
#define INVERT_X_DIR false // DELTA does not invert
#define INVERT_Y_DIR false
@@ -359,14 +407,53 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
//============================= Bed Auto Leveling ===========================
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
+#define Z_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
#ifdef ENABLE_AUTO_BED_LEVELING
- // these are the positions on the bed to do the probing
- #define LEFT_PROBE_BED_POSITION 15
- #define RIGHT_PROBE_BED_POSITION 170
- #define BACK_PROBE_BED_POSITION 180
- #define FRONT_PROBE_BED_POSITION 20
+// There are 2 different ways to pick the X and Y locations to probe:
+
+// - "grid" mode
+// Probe every point in a rectangular grid
+// You must specify the rectangle, and the density of sample points
+// This mode is preferred because there are more measurements.
+// It used to be called ACCURATE_BED_LEVELING but "grid" is more descriptive
+
+// - "3-point" mode
+// Probe 3 arbitrary points on the bed (that aren't colinear)
+// You must specify the X & Y coordinates of all 3 points
+
+ #define AUTO_BED_LEVELING_GRID
+ // with AUTO_BED_LEVELING_GRID, the bed is sampled in a
+ // AUTO_BED_LEVELING_GRID_POINTSxAUTO_BED_LEVELING_GRID_POINTS grid
+ // and least squares solution is calculated
+ // Note: this feature occupies 10'206 byte
+ #ifdef AUTO_BED_LEVELING_GRID
+
+ // set the rectangle in which to probe
+ #define LEFT_PROBE_BED_POSITION 15
+ #define RIGHT_PROBE_BED_POSITION 170
+ #define BACK_PROBE_BED_POSITION 180
+ #define FRONT_PROBE_BED_POSITION 20
+
+ // set the number of grid points per dimension
+ // I wouldn't see a reason to go above 3 (=9 probing points on the bed)
+ #define AUTO_BED_LEVELING_GRID_POINTS 2
+
+
+ #else // not AUTO_BED_LEVELING_GRID
+ // with no grid, just probe 3 arbitrary points. A simple cross-product
+ // is used to esimate the plane of the print bed
+
+ #define ABL_PROBE_PT_1_X 15
+ #define ABL_PROBE_PT_1_Y 180
+ #define ABL_PROBE_PT_2_X 15
+ #define ABL_PROBE_PT_2_Y 20
+ #define ABL_PROBE_PT_3_X 170
+ #define ABL_PROBE_PT_3_Y 20
+
+ #endif // AUTO_BED_LEVELING_GRID
+
// these are the offsets to the probe relative to the extruder tip (Hotend - Probe)
#define X_PROBE_OFFSET_FROM_EXTRUDER -25
@@ -381,6 +468,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
#define Z_RAISE_BEFORE_PROBING 15 //How much the extruder will be raised before traveling to the first probing point.
#define Z_RAISE_BETWEEN_PROBINGS 5 //How much the extruder will be raised when traveling from between next probing points
+ //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
+ //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
//If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
//The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
@@ -406,7 +495,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
#endif
-#endif
+#endif // ENABLE_AUTO_BED_LEVELING
// The position of the homing switches
@@ -451,6 +540,15 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
//=============================Additional Features===========================
//===========================================================================
+// Custom M code points
+#define CUSTOM_M_CODES
+#ifdef CUSTOM_M_CODES
+ #define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
+ #define Z_PROBE_OFFSET_RANGE_MIN -15
+ #define Z_PROBE_OFFSET_RANGE_MAX -5
+#endif
+
+
// EEPROM
// The microcontroller can store settings in the EEPROM, e.g. max velocity...
// M500 - stores parameters in EEPROM
@@ -476,10 +574,13 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
//#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
//#define SDSUPPORT // Enable SD Card Support in Hardware Console
//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
+//#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
//#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
//#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
//#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
//#define ULTIPANEL //the UltiPanel as on Thingiverse
+//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
+//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
// The MaKr3d Makr-Panel with graphic controller and SD support
// http://reprap.org/wiki/MaKr3d_MaKrPanel
@@ -565,6 +666,21 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
#define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD
#define NEWPANEL
#define ULTIPANEL
+
+ #ifndef ENCODER_PULSES_PER_STEP
+ #define ENCODER_PULSES_PER_STEP 4
+ #endif
+
+ #ifndef ENCODER_STEPS_PER_MENU_ITEM
+ #define ENCODER_STEPS_PER_MENU_ITEM 1
+ #endif
+
+
+ #ifdef LCD_USE_I2C_BUZZER
+ #define LCD_FEEDBACK_FREQUENCY_HZ 1000
+ #define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
+ #endif
+
#endif
// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
@@ -587,7 +703,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
//#define SR_LCD
#ifdef SR_LCD
- #define SR_LCD_2W_NL // Non latching 2 wire shiftregister
+ #define SR_LCD_2W_NL // Non latching 2 wire shift register
//#define NEWPANEL
#endif
@@ -676,6 +792,35 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
//#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
//#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
+/**********************************************************************\
+ * Support for a filament diameter sensor
+ * Also allows adjustment of diameter at print time (vs at slicing)
+ * Single extruder only at this point (extruder 0)
+ *
+ * Motherboards
+ * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector
+ * 81 - Printrboard - Uses Analog input 2 on the Aux 2 connector
+ * 301 - Rambo - uses Analog input 3
+ * Note may require analog pins to be defined for different motherboards
+ **********************************************************************/
+#define FILAMENT_SENSOR
+#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
+#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
+
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation
+#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm
+#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm
+#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
+
+//defines used in the code
+#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
+
+
+
+
+
+
+
#include "Configuration_adv.h"
#include "thermistortables.h"
diff --git a/Marlin/example_configurations/delta/Configuration_adv.h b/Marlin/example_configurations/delta/Configuration_adv.h
index 4d6e78b4d9ac908dc377372040a62cdf4e9b3aa4..ee42481be1ac63fcb9bdfdb82bf89b0b08a56137 100644
--- a/Marlin/example_configurations/delta/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/Configuration_adv.h
@@ -281,6 +281,9 @@
//=============================Additional Features===========================
//===========================================================================
+//#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
+#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
+
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
@@ -401,8 +404,16 @@ const unsigned int dropsegments=5; //everything with less than this number of st
// the moves are than replaced by the firmware controlled ones.
// #define FWRETRACT //ONLY PARTIALLY TESTED
-#define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt
-
+#ifdef FWRETRACT
+ #define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt
+ #define RETRACT_LENGTH 3 //default retract length (positive mm)
+ #define RETRACT_LENGTH_SWAP 13 //default swap retract length (positive mm), for extruder change
+ #define RETRACT_FEEDRATE 45 //default feedrate for retracting (mm/s)
+ #define RETRACT_ZLIFT 0 //default retract Z-lift
+ #define RETRACT_RECOVER_LENGTH 0 //default additional recover length (mm, added to retract length when recovering)
+ #define RETRACT_RECOVER_LENGTH_SWAP 0 //default additional swap recover length (mm, added to retract length when recovering from extruder change)
+ #define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
+#endif
//adds support for experimental filament exchange support M600; requires display
#ifdef ULTIPANEL
diff --git a/Marlin/language.h b/Marlin/language.h
index ee5d77dbcd3beb5d9b359b91543f62bb3bf818b0..8fd165b4009e7018f1896b5a69382fb4a6ad266d 100644
--- a/Marlin/language.h
+++ b/Marlin/language.h
@@ -665,7 +665,7 @@
#define MSG_AUTOSTART " Autostart"
#define MSG_DISABLE_STEPPERS "Apagar motores"
#define MSG_AUTO_HOME "Llevar al origen"
- #define MSG_SET_HOME_OFFSETS "Set home offsets"
+ #define MSG_SET_HOME_OFFSETS "Ajustar offsets"
#define MSG_SET_ORIGIN "Establecer cero"
#define MSG_PREHEAT_PLA "Precalentar PLA"
#define MSG_PREHEAT_PLA0 "Precalentar PLA 1"
@@ -682,8 +682,8 @@
#define MSG_PREHEAT_ABS_BEDONLY "Precal. ABS Base"
#define MSG_PREHEAT_ABS_SETTINGS "Ajustar temp. ABS"
#define MSG_COOLDOWN "Enfriar"
- #define MSG_SWITCH_PS_ON "Switch Power On"
- #define MSG_SWITCH_PS_OFF "Switch Power Off"
+ #define MSG_SWITCH_PS_ON "Encender"
+ #define MSG_SWITCH_PS_OFF "Apagar"
#define MSG_EXTRUDE "Extruir"
#define MSG_RETRACT "Retraer"
#define MSG_MOVE_AXIS "Mover ejes"
@@ -727,7 +727,7 @@
#define MSG_Z "z"
#define MSG_E "e"
#define MSG_VMIN "Vmin"
- #define MSG_VTRAV_MIN "VTrav min"
+ #define MSG_VTRAV_MIN "Vvacio min"
#define MSG_AMAX "Amax"
#define MSG_A_RETRACT "A-retrac."
#define MSG_XSTEPS "X pasos/mm"
@@ -775,14 +775,14 @@
#define MSG_CONTROL_ARROW "Control"
#define MSG_RETRACT_ARROW "Retraer"
#define MSG_STEPPER_RELEASED "Desacoplada."
- #define MSG_ZPROBE_OUT "Z probe out. bed"
- #define MSG_POSITION_UNKNOWN "Home X/Y before Z"
- #define MSG_ZPROBE_ZOFFSET "Z Offset"
+ #define MSG_ZPROBE_OUT "sonda Z fuera"
+ #define MSG_POSITION_UNKNOWN "Reiniciar X/Y y Z"
+ #define MSG_ZPROBE_ZOFFSET "Offset Z"
#define MSG_BABYSTEP_X "Babystep X"
#define MSG_BABYSTEP_Y "Babystep Y"
#define MSG_BABYSTEP_Z "Babystep Z"
#define MSG_ENDSTOP_ABORT "Endstop abort"
- #define MSG_CONTRAST "Contrast"
+ #define MSG_CONTRAST "Contraste"
#endif
diff --git a/Marlin/stepper.cpp b/Marlin/stepper.cpp
index 9e22eb198bd50a1cb9c8b3cf59690b1331c0372f..b2e7d1208055df1f7e22a9f9e6302b788d1a1481 100644
--- a/Marlin/stepper.cpp
+++ b/Marlin/stepper.cpp
@@ -559,6 +559,58 @@ ISR(TIMER1_COMPA_vect)
#endif //ADVANCE
counter_x += current_block->steps_x;
+ #ifdef CONFIG_STEPPERS_TOSHIBA
+ /* The toshiba stepper controller require much longer pulses
+ * tjerfore we 'stage' decompose the pulses between high, and
+ * low instead of doing each in turn. The extra tests add enough
+ * lag to allow it work with without needing NOPs */
+ if (counter_x > 0) {
+ WRITE(X_STEP_PIN, HIGH);
+ }
+
+ counter_y += current_block->steps_y;
+ if (counter_y > 0) {
+ WRITE(Y_STEP_PIN, HIGH);
+ }
+
+ counter_z += current_block->steps_z;
+ if (counter_z > 0) {
+ WRITE(Z_STEP_PIN, HIGH);
+ }
+
+ #ifndef ADVANCE
+ counter_e += current_block->steps_e;
+ if (counter_e > 0) {
+ WRITE_E_STEP(HIGH);
+ }
+ #endif //!ADVANCE
+
+ if (counter_x > 0) {
+ counter_x -= current_block->step_event_count;
+ count_position[X_AXIS]+=count_direction[X_AXIS];
+ WRITE(X_STEP_PIN, LOW);
+ }
+
+ if (counter_y > 0) {
+ counter_y -= current_block->step_event_count;
+ count_position[Y_AXIS]+=count_direction[Y_AXIS];
+ WRITE(Y_STEP_PIN, LOW);
+ }
+
+ if (counter_z > 0) {
+ counter_z -= current_block->step_event_count;
+ count_position[Z_AXIS]+=count_direction[Z_AXIS];
+ WRITE(Z_STEP_PIN, LOW);
+ }
+
+ #ifndef ADVANCE
+ if (counter_e > 0) {
+ counter_e -= current_block->step_event_count;
+ count_position[E_AXIS]+=count_direction[E_AXIS];
+ WRITE_E_STEP(LOW);
+ }
+ #endif //!ADVANCE
+#else
if (counter_x > 0) {
#ifdef DUAL_X_CARRIAGE
if (extruder_duplication_enabled){
@@ -635,6 +687,7 @@ ISR(TIMER1_COMPA_vect)
WRITE_E_STEP(INVERT_E_STEP_PIN);
}
#endif //!ADVANCE
+ #endif
step_events_completed += 1;
if(step_events_completed >= current_block->step_event_count) break;
}
diff --git a/Marlin/ultralcd.cpp b/Marlin/ultralcd.cpp
index 8d55bb91d3e7af20b86de029917744aa77674d12..3f1952f5e99024ddf5ed386a3c4f00c12289b4a1 100644
--- a/Marlin/ultralcd.cpp
+++ b/Marlin/ultralcd.cpp
@@ -162,6 +162,8 @@ bool lcd_oldcardstatus;
menuFunc_t currentMenu = lcd_status_screen; /* function pointer to the currently active menu */
uint32_t lcd_next_update_millis;
uint8_t lcd_status_update_delay;
+bool ignore_click = false;
+bool wait_for_unclick;
uint8_t lcdDrawUpdate = 2; /* Set to none-zero when the LCD needs to draw, decreased after every draw. Set to 2 in LCD routines so the LCD gets at least 1 full redraw (first redraw is partial) */
//prevMenu and prevEncoderPosition are used to store the previous menu location when editing settings.
@@ -189,7 +191,26 @@ static void lcd_status_screen()
lcd_status_update_delay = 10; /* redraw the main screen every second. This is easier then trying keep track of all things that change on the screen */
}
#ifdef ULTIPANEL
- if (LCD_CLICKED)
+
+ bool current_click = LCD_CLICKED;
+
+ if (ignore_click) {
+ if (wait_for_unclick) {
+ if (!current_click) {
+ ignore_click = wait_for_unclick = false;
+ }
+ else {
+ current_click = false;
+ }
+ }
+ else if (current_click) {
+ lcd_quick_feedback();
+ wait_for_unclick = true;
+ current_click = false;
+ }
+ }
+
+ if (current_click)
{
currentMenu = lcd_main_menu;
encoderPosition = 0;
@@ -1315,6 +1336,12 @@ void lcd_update()
}
}
+void lcd_ignore_click(bool b)
+{
+ ignore_click = b;
+ wait_for_unclick = false;
+}
+
void lcd_setstatus(const char* message)
{
if (lcd_status_message_level > 0)
diff --git a/Marlin/ultralcd.h b/Marlin/ultralcd.h
index aacfda64ed36649ccb90d9b012370c15307da3c2..0f32eafe48296cd04bf7c7094d59a3c96dd52736 100644
--- a/Marlin/ultralcd.h
+++ b/Marlin/ultralcd.h
@@ -49,6 +49,8 @@
void lcd_buzz(long duration,uint16_t freq);
bool lcd_clicked();
+ void lcd_ignore_click(bool b=true);
+
#ifdef NEWPANEL
#define EN_C (1<<BLEN_C)
#define EN_B (1<<BLEN_B)
diff --git a/README.md b/README.md
index 5eda8465cdebffd4992225aec54f732d33e297d0..d11925ff79d6d2d1dac011f411da3dad209292eb 100644
--- a/README.md
+++ b/README.md
@@ -2,6 +2,7 @@
Marlin 3D Printer Firmware
==========================
[](https://scan.coverity.com/projects/2224)
+[](https://travis-ci.org/ErikZalm/Marlin)
Marlin has a GPL license because I believe in open development.
Please do not use this code in products (3D printers, CNC etc) that are closed source or are crippled by a patent.