diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 3004cf12581c7b980da65d5639f00a9ecf6f0d43..366397ca021d2373131f7c22282309b666c7a543 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -1700,38 +1700,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index 3de19977a1399b1f559ba17ff7737e4025cd4aa3..daaf321dcbe1e257ee4b2bef5e9be06817c8f160 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -1256,6 +1256,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/default/Configuration.h b/Marlin/src/config/default/Configuration.h index 3004cf12581c7b980da65d5639f00a9ecf6f0d43..366397ca021d2373131f7c22282309b666c7a543 100644 --- a/Marlin/src/config/default/Configuration.h +++ b/Marlin/src/config/default/Configuration.h @@ -1700,38 +1700,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/default/Configuration_adv.h b/Marlin/src/config/default/Configuration_adv.h index 3de19977a1399b1f559ba17ff7737e4025cd4aa3..daaf321dcbe1e257ee4b2bef5e9be06817c8f160 100644 --- a/Marlin/src/config/default/Configuration_adv.h +++ b/Marlin/src/config/default/Configuration_adv.h @@ -1256,6 +1256,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h index 11aacd5246e048b20c92af9438b8216b26d305e5..375b3d0431e6f007ba9dc343c89c5c0574c5d78e 100644 --- a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h +++ b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h @@ -1720,38 +1720,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h index 701743a122bdb2b7359b22ac521747a795fce064..435378bb179b240fc492a0f8f8e1e7981dbfaa42 100644 --- a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h +++ b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h @@ -1255,6 +1255,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h b/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h index 768f452eb87964525e515fba42122a9d5e8229e4..b535c4d62c63af64238ea34e566eee72b6fbb270 100644 --- a/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h +++ b/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h @@ -1700,38 +1700,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/Anet/A6/Configuration.h b/Marlin/src/config/examples/Anet/A6/Configuration.h index 2de8adf1b89aca1a89ede73d555f31049ec3bf0b..ad85db95986ff6ad570b31251834e052f6812b5e 100644 --- a/Marlin/src/config/examples/Anet/A6/Configuration.h +++ b/Marlin/src/config/examples/Anet/A6/Configuration.h @@ -1859,38 +1859,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/Anet/A6/Configuration_adv.h b/Marlin/src/config/examples/Anet/A6/Configuration_adv.h index c21499b440d95b0dac38a432d3717a1910c8989e..8a9d8c88faed165131d18778376e78e0af45d98c 100644 --- a/Marlin/src/config/examples/Anet/A6/Configuration_adv.h +++ b/Marlin/src/config/examples/Anet/A6/Configuration_adv.h @@ -1255,6 +1255,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/Anet/A8/Configuration.h b/Marlin/src/config/examples/Anet/A8/Configuration.h index 2684bb9b35b5764d11d1199e71d73853aac5bc77..4cec1e8400110ea8e95db10b436c4f6c7e91cfde 100644 --- a/Marlin/src/config/examples/Anet/A8/Configuration.h +++ b/Marlin/src/config/examples/Anet/A8/Configuration.h @@ -1708,38 +1708,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/Anet/A8/Configuration_adv.h b/Marlin/src/config/examples/Anet/A8/Configuration_adv.h index b843fca827dc418d602910e5b3d8c08622504144..d0daf81ab59ba520106da2ff43cb532021e49351 100644 --- a/Marlin/src/config/examples/Anet/A8/Configuration_adv.h +++ b/Marlin/src/config/examples/Anet/A8/Configuration_adv.h @@ -1255,6 +1255,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h b/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h index 4017d2688553302b3bb4e11823ec8c210f590c62..c4b133c76c4cdc2cf367caed2cdd8dbf590497df 100644 --- a/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h +++ b/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h @@ -1695,38 +1695,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h b/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h index 88f73533a7c260726dd00e03e88959af6d8412b5..af76259d110aff2940b9cbd3255d09be41828eda 100644 --- a/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h +++ b/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h @@ -1257,6 +1257,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/BQ/Hephestos/Configuration.h b/Marlin/src/config/examples/BQ/Hephestos/Configuration.h index 24b7d63d8c883fcd7a909df1172d0cb561354135..2aeeadfb8e8a0221482417192ad8cf811abfd312 100644 --- a/Marlin/src/config/examples/BQ/Hephestos/Configuration.h +++ b/Marlin/src/config/examples/BQ/Hephestos/Configuration.h @@ -1691,38 +1691,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h b/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h index 51f75a4729e12f8ea2eb66c38ff9d118c0faeb84..94043ed98b2bb08dbc930da4c6d8f3e68e58a1ea 100644 --- a/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h +++ b/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h @@ -1255,6 +1255,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h index 901c3830478f3bf62220d02d4d6fa8ea390d830d..2ce8919adcfa3122669c62c754646b7e5bbed6d5 100644 --- a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h +++ b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h @@ -1701,38 +1701,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 2.00 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.60 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h index 1a2e7173da2cb59f9f0f67b4cc1ad17fbef6f2e9..9d9fdad60676f086b3e3006261f6a1f3d3eac36d 100644 --- a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h +++ b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h @@ -1252,6 +1252,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 2.00 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.60 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/BQ/WITBOX/Configuration.h b/Marlin/src/config/examples/BQ/WITBOX/Configuration.h index 834089c525fbcc56162782b14f1b9800b64cff23..d62719b2f5cc45eb5c24d34d2521aba6d909d520 100644 --- a/Marlin/src/config/examples/BQ/WITBOX/Configuration.h +++ b/Marlin/src/config/examples/BQ/WITBOX/Configuration.h @@ -1691,38 +1691,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h b/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h index 51f75a4729e12f8ea2eb66c38ff9d118c0faeb84..94043ed98b2bb08dbc930da4c6d8f3e68e58a1ea 100644 --- a/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h +++ b/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h @@ -1255,6 +1255,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/Cartesio/Configuration.h b/Marlin/src/config/examples/Cartesio/Configuration.h index e1934c9d909e4fa9e59054672026bb58ee43f87f..dbcf31bf854b4e58fb5e2990cd70254cd80f27a9 100644 --- a/Marlin/src/config/examples/Cartesio/Configuration.h +++ b/Marlin/src/config/examples/Cartesio/Configuration.h @@ -1699,38 +1699,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/Cartesio/Configuration_adv.h b/Marlin/src/config/examples/Cartesio/Configuration_adv.h index d2cc658717f81e7d3de1f22469a88d39312bf506..e96d1d777a1147ea73200ffe9f055992582bafef 100644 --- a/Marlin/src/config/examples/Cartesio/Configuration_adv.h +++ b/Marlin/src/config/examples/Cartesio/Configuration_adv.h @@ -1255,6 +1255,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/Creality/CR-10/Configuration.h b/Marlin/src/config/examples/Creality/CR-10/Configuration.h index cb430c48a1880552673d77e34b0a32a157855437..fb46d5cd739723d67c3bd596cbc91ca370ec02e8 100755 --- a/Marlin/src/config/examples/Creality/CR-10/Configuration.h +++ b/Marlin/src/config/examples/Creality/CR-10/Configuration.h @@ -1710,41 +1710,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#define DEFAULT_STDDEV_FILAMENT_DIA 0.05 // Typical estimate for cheap filament -//#define DEFAULT_STDDEV_FILAMENT_DIA 0.02 // Typical advertised for higher quality filament - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT (DEFAULT_NOMINAL_FILAMENT_DIA+4*DEFAULT_STDDEV_FILAMENT_DIA) // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT (DEFAULT_NOMINAL_FILAMENT_DIA-4*DEFAULT_STDDEV_FILAMENT_DIA) // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h index 5c01a68547e3f9024190a6063607113695374ecc..0236f542c2782ea78b63c4a0fb90a251f4d5739d 100644 --- a/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h +++ b/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h @@ -1255,6 +1255,43 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#define DEFAULT_STDDEV_FILAMENT_DIA 0.05 // Typical estimate for cheap filament +//#define DEFAULT_STDDEV_FILAMENT_DIA 0.02 // Typical advertised for higher quality filament + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT (DEFAULT_NOMINAL_FILAMENT_DIA+4*DEFAULT_STDDEV_FILAMENT_DIA) // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT (DEFAULT_NOMINAL_FILAMENT_DIA-4*DEFAULT_STDDEV_FILAMENT_DIA) // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/Felix/Configuration.h b/Marlin/src/config/examples/Felix/Configuration.h index 02c01555529769b3c4bca880af16e20d6423082a..ff7c03b1f0602a6a00b75ea3449d618cd794c559 100644 --- a/Marlin/src/config/examples/Felix/Configuration.h +++ b/Marlin/src/config/examples/Felix/Configuration.h @@ -1682,38 +1682,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/Felix/Configuration_adv.h b/Marlin/src/config/examples/Felix/Configuration_adv.h index dc44e929cc8ce33e4ef0bf3ea8d8e66e20e992a1..4901703a10488e344ca52161bd5247468ecdad68 100644 --- a/Marlin/src/config/examples/Felix/Configuration_adv.h +++ b/Marlin/src/config/examples/Felix/Configuration_adv.h @@ -1255,6 +1255,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/Felix/DUAL/Configuration.h b/Marlin/src/config/examples/Felix/DUAL/Configuration.h index b79f659df47b182dde886b383b3d915134d358a1..6d56df39c808c6ce29c04504933a9ef902cc6f17 100644 --- a/Marlin/src/config/examples/Felix/DUAL/Configuration.h +++ b/Marlin/src/config/examples/Felix/DUAL/Configuration.h @@ -1682,38 +1682,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h index 28a9a54036d7d7c3772be8be64872cff154d5f3e..8617a686fde8eccabecb2e34811d9cf6258ecd32 100644 --- a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h +++ b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h @@ -1697,38 +1697,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h index 7df606afd5de4af30a88be2e42f4f3cda00e6067..36edbbf07e37d0a578a0ab618c768b37590e3b78 100644 --- a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h +++ b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h @@ -1256,6 +1256,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h b/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h index 263df4a75140f63d078ad449fc02079b66f5b6a5..9406938b136344debd1f15c51705baf43e8d6d2c 100644 --- a/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h +++ b/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h @@ -1715,40 +1715,6 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - /** * Customize common displays for GT2560 */ diff --git a/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h index 636e86006680f2448bbed725bbe651f2fbb9774b..f17b1cbf636098194bd3faebda317bc5daaed870 100644 --- a/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h +++ b/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h @@ -1700,38 +1700,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h b/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h index f69deff547d9878a5adb93fadc38ee7f7278ff23..58ab5b7821ef6376eb69bf0476c4116093fdafff 100644 --- a/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h +++ b/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h @@ -1704,38 +1704,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h b/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h index 2d093bbeb72ee8cf29fe8713369b4b208a50cb55..c89aba5b5e857e1d52b4eee4d5645c67ec30673a 100644 --- a/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h +++ b/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h @@ -1255,6 +1255,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/Malyan/M150/Configuration.h b/Marlin/src/config/examples/Malyan/M150/Configuration.h index a5482e310630791c675e0a01805f354b1a65dbc2..83ba4ea6bdcb5d26bedf88001edd101f841af25b 100644 --- a/Marlin/src/config/examples/Malyan/M150/Configuration.h +++ b/Marlin/src/config/examples/Malyan/M150/Configuration.h @@ -1728,38 +1728,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h b/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h index 562207353f5e8c55f7173cd386509932c68f7bb9..1779d4e7a87082014ec12ff7c79a86af4678b18a 100644 --- a/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h +++ b/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h @@ -1249,6 +1249,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h b/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h index 581d1d4f7789ad71ae9698d849b3f9bff35eb4f7..b6a7a1e09abdce1dd47bf5afd43849dac5640828 100644 --- a/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h +++ b/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h @@ -1704,38 +1704,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h index 9963fc7bd3a41b07dd694127dd5ff2d17c42fdfe..06f213012b0afa747bdd64fb83912dd9b4c0c327 100644 --- a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h +++ b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h @@ -1704,38 +1704,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h index 1081154984b48779afadb8af140c8318f1597267..4026ec4e5ec9a651c73886f85267d53fdb630f5e 100644 --- a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h +++ b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h @@ -1259,6 +1259,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/Mks/Sbase/Configuration.h b/Marlin/src/config/examples/Mks/Sbase/Configuration.h index 0b30b26226e13db82490702e6d0b7e93441b0d95..c4438d07c257193b27b92aac5238cbf3418f8c37 100644 --- a/Marlin/src/config/examples/Mks/Sbase/Configuration.h +++ b/Marlin/src/config/examples/Mks/Sbase/Configuration.h @@ -1675,38 +1675,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h b/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h index 1f02f41e7cd3a965b8948a2cd4515df6b01bfb4e..a04f3148c4dbcdfc2f10fe98f70af1750807dda7 100644 --- a/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h +++ b/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h @@ -1277,6 +1277,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h b/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h index 08299d6d8bd57ece7d46821b3dd3e3aa56713844..93ba416eb5a7f9aa0f6a8da784d8f0cedd602fbe 100644 --- a/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h +++ b/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h @@ -1700,38 +1700,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/RigidBot/Configuration.h b/Marlin/src/config/examples/RigidBot/Configuration.h index 56197e605bedd5b3480ef53921d1e63b166d1b66..2ff17d6962217f98c5483486e8619fef4f3429da 100644 --- a/Marlin/src/config/examples/RigidBot/Configuration.h +++ b/Marlin/src/config/examples/RigidBot/Configuration.h @@ -1700,38 +1700,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/RigidBot/Configuration_adv.h b/Marlin/src/config/examples/RigidBot/Configuration_adv.h index 073148c13ee4fac76fc1e381204a307e13c21165..a80dec718d6ecf69a3344fe9d2acda76f6942522 100644 --- a/Marlin/src/config/examples/RigidBot/Configuration_adv.h +++ b/Marlin/src/config/examples/RigidBot/Configuration_adv.h @@ -1255,6 +1255,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/SCARA/Configuration.h b/Marlin/src/config/examples/SCARA/Configuration.h index 5ae2816ac838551bac6b33f0bee6dfdbe02fb954..f8076184a263ee569e94e54b8c33baafa5901fc8 100644 --- a/Marlin/src/config/examples/SCARA/Configuration.h +++ b/Marlin/src/config/examples/SCARA/Configuration.h @@ -1712,38 +1712,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/SCARA/Configuration_adv.h b/Marlin/src/config/examples/SCARA/Configuration_adv.h index 3f5d9851fde7e043ce94ff5cd2a5a0b461fa27a5..3c5bda64e24f2f0cb9b821d1475a2c1a9d7ea5fe 100644 --- a/Marlin/src/config/examples/SCARA/Configuration_adv.h +++ b/Marlin/src/config/examples/SCARA/Configuration_adv.h @@ -1255,6 +1255,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/STM32F10/Configuration.h b/Marlin/src/config/examples/STM32F10/Configuration.h index 29e02f91b0299c7189d9629bae7e34461bfe95ca..0b0fb72cc5825774b9948ec3312f8d6f1d2fbf8b 100644 --- a/Marlin/src/config/examples/STM32F10/Configuration.h +++ b/Marlin/src/config/examples/STM32F10/Configuration.h @@ -1703,38 +1703,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/Sanguinololu/Configuration.h b/Marlin/src/config/examples/Sanguinololu/Configuration.h index 0e514fc325873aa56dcc59e85a2c0797f9c58d5a..f7db262bdf130ac70bec5fb4c1a189f6fc2b7422 100644 --- a/Marlin/src/config/examples/Sanguinololu/Configuration.h +++ b/Marlin/src/config/examples/Sanguinololu/Configuration.h @@ -1731,38 +1731,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h b/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h index 8bee1f39a7eb19d179ee25a353f1ee328a19e942..bc5d2fcdb090daff33f8cfc15c2c3403b7802b85 100644 --- a/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h +++ b/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h @@ -1244,6 +1244,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/TinyBoy2/Configuration.h b/Marlin/src/config/examples/TinyBoy2/Configuration.h index 40a88d2518b891de4c23b9fcbec45a6f40f8be89..fe664fb81b8e650099e89f7c231cbaf7ec1c72a3 100644 --- a/Marlin/src/config/examples/TinyBoy2/Configuration.h +++ b/Marlin/src/config/examples/TinyBoy2/Configuration.h @@ -1756,38 +1756,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h b/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h index dcd3bfcc5ac050f440b5a12a7dcbab93faeb1f6a..c07b3627fb5d4cc4a9f285b19a32bef1bd2f3db1 100644 --- a/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h +++ b/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h @@ -1255,6 +1255,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h index 6f2cff13a0625cc5ce1c148e5ec73ceb253a81ef..b9542ba9cd181abff10514b5d99273ebd3e2a10b 100644 --- a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h +++ b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h @@ -1701,38 +1701,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h index 5bffde3fab105d1830db8b0affade037ebff27e2..cae20c8967ab2276a166a39937a0c49efc15de92 100644 --- a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h +++ b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h @@ -1256,6 +1256,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/Velleman/K8200/Configuration.h b/Marlin/src/config/examples/Velleman/K8200/Configuration.h index 07ab2e2a5f5d004dfe4dc0cae1c114f09e9b9672..a86a015cdf615b7ae1b8af1b943df2f2f0241ce1 100644 --- a/Marlin/src/config/examples/Velleman/K8200/Configuration.h +++ b/Marlin/src/config/examples/Velleman/K8200/Configuration.h @@ -1735,38 +1735,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h b/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h index 20cc256910420fd20569609739495c68bed3fccf..64c1393622f194eeb129a0e3d80705db1810dae1 100644 --- a/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h +++ b/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h @@ -1263,6 +1263,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/Velleman/K8400/Configuration.h b/Marlin/src/config/examples/Velleman/K8400/Configuration.h index 84e5be633551ffc892cb9cc37017e15ee2f09f28..be9e366e8ecb22f417d292c77bafe8bc8481b4db 100644 --- a/Marlin/src/config/examples/Velleman/K8400/Configuration.h +++ b/Marlin/src/config/examples/Velleman/K8400/Configuration.h @@ -1700,38 +1700,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h b/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h index db8519d705488f47e4fb4286522ed4191129c4e6..86ae10e8502d522d5c24380bc15679bd6fa5a337 100644 --- a/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h +++ b/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h @@ -1256,6 +1256,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h b/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h index 200526eaa9d2e982fb96b8eb78a53dd190cff12c..c1b4bf146388c4830f037924e7f38b5084f50931 100644 --- a/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h +++ b/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h @@ -1700,38 +1700,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/adafruit/ST7565/Configuration.h b/Marlin/src/config/examples/adafruit/ST7565/Configuration.h index bfbf9bb3e8059139865aae4d8c9db4314d77157a..c8224e8cad8f059ba76bff1ad2e65e725627ba48 100644 --- a/Marlin/src/config/examples/adafruit/ST7565/Configuration.h +++ b/Marlin/src/config/examples/adafruit/ST7565/Configuration.h @@ -1700,38 +1700,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h index e167dcefa14a7db1f50ed1046eeed740564413f4..3eeac409921457cab0088c542c57bdf039360535 100644 --- a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h +++ b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h @@ -1834,38 +1834,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 1.95 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.20 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h index cc814c4618ec92dd66f23080b5052c44b6558360..0e53dd57fa800e0fa1b8f8cdc57ec574a38ceea2 100644 --- a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h +++ b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h @@ -1257,6 +1257,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 1.95 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.20 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h index 7f32b514c70d18dcae19b00249741419e39bb95a..4ac0026d03c315db4d7cd2713774267cb75fe2d2 100644 --- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h +++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h @@ -1827,38 +1827,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h index 685876a091d35c451793acc9eb38987b6afd19b6..5b2e5d5bf1023c134cc37de42bf2a62889ee9845 100644 --- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h +++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h @@ -1257,6 +1257,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/delta/generic/Configuration.h b/Marlin/src/config/examples/delta/generic/Configuration.h index de63e91acfc08507c7697b49333c514c48d85c72..265278f66ac0143b9fd3a7a821d82d9a9a27769c 100644 --- a/Marlin/src/config/examples/delta/generic/Configuration.h +++ b/Marlin/src/config/examples/delta/generic/Configuration.h @@ -1822,38 +1822,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/delta/generic/Configuration_adv.h b/Marlin/src/config/examples/delta/generic/Configuration_adv.h index 685876a091d35c451793acc9eb38987b6afd19b6..5b2e5d5bf1023c134cc37de42bf2a62889ee9845 100644 --- a/Marlin/src/config/examples/delta/generic/Configuration_adv.h +++ b/Marlin/src/config/examples/delta/generic/Configuration_adv.h @@ -1257,6 +1257,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h index 62007f2b90a2a02d0185764d49a83039f20e612c..c16901f77003b95639fe37dc0f723ce1da346c52 100644 --- a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h +++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h @@ -1825,38 +1825,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h index 685876a091d35c451793acc9eb38987b6afd19b6..5b2e5d5bf1023c134cc37de42bf2a62889ee9845 100644 --- a/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h +++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h @@ -1257,6 +1257,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h index bce2cc2e75e7b831b2e86766758f3d71e8105a6d..d62334593d82678cba891b269e2b3e36a0a35d0a 100644 --- a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h +++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h @@ -1825,38 +1825,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h index d21e170ccc2ad171a84a2dfcb9f45d4a83a5ccbe..a973ff0c2c23d69f30d7f050d00c06bd20881392 100644 --- a/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h +++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h @@ -1262,6 +1262,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h index 15ac367b45ba0db7fb2fb1d7033b06a9f585c56b..13854d3ded1e864b57d24f8defaca0d3e8cc7e34 100644 --- a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h +++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h @@ -1834,38 +1834,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h index ce3420b7cd8b9d050e7c4a3da36b02258be8e1c9..5f5c34069220c8dd242aaf3a267aa576d346005d 100644 --- a/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h +++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h @@ -1257,6 +1257,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h index 52d2b40f1222fd2b79857fd92ea467deb4d7043a..5ee1b6ae5904eb17e3c49e1eb6b5fae7ef2957ef 100644 --- a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h +++ b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h @@ -1714,38 +1714,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h index 978bca291befefa048f94069af056378cfdb875d..fca8d4b20a46814e1e152aa2c876e48822578087 100644 --- a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h +++ b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h @@ -1255,6 +1255,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/makibox/Configuration.h b/Marlin/src/config/examples/makibox/Configuration.h index 0a03d94753ef5e6612ffba8a6618f8e1a74aedaa..b7712f0c9c6b1fdc572e392e4d8ad10957bd23a2 100644 --- a/Marlin/src/config/examples/makibox/Configuration.h +++ b/Marlin/src/config/examples/makibox/Configuration.h @@ -1703,38 +1703,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/makibox/Configuration_adv.h b/Marlin/src/config/examples/makibox/Configuration_adv.h index 360692cc782a6ea79465fa4e7714ef29509de5d6..3a83b379cf2c0a4d4ae2f3ffc49c5181d50d881d 100644 --- a/Marlin/src/config/examples/makibox/Configuration_adv.h +++ b/Marlin/src/config/examples/makibox/Configuration_adv.h @@ -1255,6 +1255,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/tvrrug/Round2/Configuration.h b/Marlin/src/config/examples/tvrrug/Round2/Configuration.h index a269c9b4a753db2946f61049d56a3f01a9b615a2..703cc0ff269d9a4ba511596b0792cf7d5aa3ce5e 100644 --- a/Marlin/src/config/examples/tvrrug/Round2/Configuration.h +++ b/Marlin/src/config/examples/tvrrug/Round2/Configuration.h @@ -1695,38 +1695,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h b/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h index adef48da2b50e6f866fd195e98b7fe09ecfc5144..b7c39423d1a2da45d19505b9fce671d8f50b50a9 100644 --- a/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h +++ b/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h @@ -1255,6 +1255,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems * diff --git a/Marlin/src/config/examples/wt150/Configuration.h b/Marlin/src/config/examples/wt150/Configuration.h index a3f899a514a44b278fd51a6f03826b86c62d6590..8c0b7a3b461a989ed1fa6e4fd4b7642850432c9f 100644 --- a/Marlin/src/config/examples/wt150/Configuration.h +++ b/Marlin/src/config/examples/wt150/Configuration.h @@ -1705,38 +1705,4 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading - #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/wt150/Configuration_adv.h b/Marlin/src/config/examples/wt150/Configuration_adv.h index 0c4e309186f1a17ac82894a912054c901a21ae93..24ebd12249af9c2fdfb4c093f1af33ab514f40c6 100644 --- a/Marlin/src/config/examples/wt150/Configuration_adv.h +++ b/Marlin/src/config/examples/wt150/Configuration_adv.h @@ -1256,6 +1256,40 @@ //#define SPEED_POWER_MAX 100 // 0-100% #endif +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + /** * CNC Coordinate Systems *