diff --git a/.travis.yml b/.travis.yml
index d7df3d9392dc75ced18d0007eb6b423cde75bc6d..cb1c650a72c6f8b7912d8a04ce81303c7c6631de 100644
--- a/.travis.yml
+++ b/.travis.yml
@@ -116,7 +116,7 @@ script:
# ULTIMAKERCONTROLLER, FILAMENT_LCD_DISPLAY, FILAMENT_WIDTH_SENSOR,
# PRINTCOUNTER, NOZZLE_PARK_FEATURE, NOZZLE_CLEAN_FEATURE, PCA9632,
# Z_DUAL_STEPPER_DRIVERS, Z_DUAL_ENDSTOPS, BEZIER_CURVE_SUPPORT, EXPERIMENTAL_I2CBUS,
- # ADVANCED_PAUSE_FEATURE, PARK_HEAD_ON_PAUSE, LCD_INFO_MENU,
+ # ADVANCED_PAUSE_FEATURE, ADVANCED_PAUSE_CONTINUOUS_PURGE, PARK_HEAD_ON_PAUSE, LCD_INFO_MENU,
# EEPROM_SETTINGS, EEPROM_CHITCHAT, M100_FREE_MEMORY_WATCHER,
# INCH_MODE_SUPPORT, TEMPERATURE_UNITS_SUPPORT
#
@@ -127,7 +127,7 @@ script:
- opt_enable ULTIMAKERCONTROLLER SDSUPPORT
- opt_enable PRINTCOUNTER NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE PCA9632 USE_XMAX_PLUG
- opt_enable_adv BEZIER_CURVE_SUPPORT EXPERIMENTAL_I2CBUS
- - opt_enable_adv ADVANCED_PAUSE_FEATURE FILAMENT_LOAD_UNLOAD_GCODES PARK_HEAD_ON_PAUSE LCD_INFO_MENU M114_DETAIL
+ - opt_enable_adv ADVANCED_PAUSE_FEATURE ADVANCED_PAUSE_CONTINUOUS_PURGE FILAMENT_LOAD_UNLOAD_GCODES PARK_HEAD_ON_PAUSE LCD_INFO_MENU M114_DETAIL
- opt_set_adv PWM_MOTOR_CURRENT {1300,1300,1250}
- opt_set_adv I2C_SLAVE_ADDRESS 63
- build_marlin_pio ${TRAVIS_BUILD_DIR} ${TEST_PLATFORM}
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index a3ce94bbb8b3395130198d95f038631391dcbdbe..cad1f8f555103d6e253046103ec521c0c68d53ba 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/default/Configuration_adv.h b/Marlin/src/config/default/Configuration_adv.h
index a3ce94bbb8b3395130198d95f038631391dcbdbe..cad1f8f555103d6e253046103ec521c0c68d53ba 100644
--- a/Marlin/src/config/default/Configuration_adv.h
+++ b/Marlin/src/config/default/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
index 54ca5c99f4a34df0b83d32b6609ce3536756effe..b87ff8a38f74acd84f0a027d092dffa2a794dc7d 100644
--- a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
+++ b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/Anet/A6/Configuration_adv.h b/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
index 82e0f7f334d728addd6eda2854f567d017968ed8..2f287131de218b16742391dd1c5b9a3a8e4c038c 100644
--- a/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/Anet/A8/Configuration_adv.h b/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
index 1ba8676f182d352e4de9dd346799d1b00a8c0ea6..927cba6c2fcabad90795b79a6399551bce772dab 100644
--- a/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h b/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
index a3ce94bbb8b3395130198d95f038631391dcbdbe..cad1f8f555103d6e253046103ec521c0c68d53ba 100644
--- a/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
+++ b/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
index 5467e126a8ea81d73262c33eefdc7b5f06439e1b..7e4698e82e642f6918bf398c597bf7dbc21befd1 100644
--- a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h
index 5cc54a3bba589409fb1af6a17ebff0b154e299b9..33009b72a7f6b347e6c71a9cb5b50c0e6a3d3cf7 100644
--- a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h b/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
index 7c377cff1fbdd8498fd73609b24388dd92850344..50f05e15441fb2a45ecb8719743b3fa765e887b1 100644
--- a/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
index adef69c196d87ab07d2b869d7158337c5671a0e2..327d3a1719a834f167635b267fdd1b2b3a1d591e 100644
--- a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h b/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
index 7c377cff1fbdd8498fd73609b24388dd92850344..50f05e15441fb2a45ecb8719743b3fa765e887b1 100644
--- a/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/Cartesio/Configuration_adv.h b/Marlin/src/config/examples/Cartesio/Configuration_adv.h
index 7c81d3251518ba36ada7f987af4f0583d63ee549..52dbf573b2e30e29e3ed4cf9490208e586172adb 100644
--- a/Marlin/src/config/examples/Cartesio/Configuration_adv.h
+++ b/Marlin/src/config/examples/Cartesio/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
index 698ae1eb6726650e72194b24cc6b630830ea33d7..ff2199eade65371cc6304cccda51ad217b0133b5 100755
--- a/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 120 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 6 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h
index 0db2bd30feea5fd806136e19969a6566b385cd5a..af293884358091d5ead159e0d26ef1040cc5b2fe 100644
--- a/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 120 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 6 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h b/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h
index ed3002ea58d8a042af73d89415d991921a9aef87..588c1678725024612b2b30bd045342e3ca73f282 100644
--- a/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h b/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
index d8ff542b0c7db7576b0e0a8bdeedba4543561162..1068d8dbc6e0fbbe12fb1d420a426212e41ff895 100644
--- a/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/Felix/Configuration_adv.h b/Marlin/src/config/examples/Felix/Configuration_adv.h
index 63623eec6b2068849595cec88e80896792383a17..5648e8ef5378971255762a2a296d7142a92a1ce0 100644
--- a/Marlin/src/config/examples/Felix/Configuration_adv.h
+++ b/Marlin/src/config/examples/Felix/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
index d440dde4a71f6334ea1d95bceaaff7dd8214d19b..c409df4e7559665039984280994536ecfd2d025a 100644
--- a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
+++ b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h b/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
index cc3cb11d9ff778fb1539f1085f592fe873422bec..d1e6b4b6125118b9c35c38c7f480e35e1cf9527b 100644
--- a/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
+++ b/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h b/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
index d2a2ac2f3ef11f9fddc8dfe0ae1a9c48ba8ce0f0..fb2fe82a7b79f6dedd1edbf80ae4a0fc847306cd 100644
--- a/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
+++ b/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 6 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/MakerParts/Configuration_adv.h b/Marlin/src/config/examples/MakerParts/Configuration_adv.h
index a3e67038aaebf03b4fd0cfe4654aa5d243c790cb..8cd4f82b327d4620929f1192bcf4010f2f4e354b 100644
--- a/Marlin/src/config/examples/MakerParts/Configuration_adv.h
+++ b/Marlin/src/config/examples/MakerParts/Configuration_adv.h
@@ -922,6 +922,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h b/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
index d3e6b3e68e7bd78dc16706c34fa8cabfce54910f..5ebfc85788efa6919ad89bdaf8c764e2000a3c7c 100644
--- a/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
+++ b/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h b/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
index be7120c609c40a9a59ad32c87127167ac9677e93..4ddf52f91e5a4700154b3b6690dd4f24fe02a93f 100644
--- a/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
+++ b/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
index 2def303e7fa9673afb724388dc610591c21c5698..05bd3cf83237e370c235b87bbdf3a99571068222 100644
--- a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
+++ b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h b/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
index fbf13edfa12503c72b2577fcfaf8f4356ff86fcb..88c2315446efe19dd0d6be559f4dbadde2f97853 100644
--- a/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
+++ b/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
@@ -929,6 +929,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/RigidBot/Configuration_adv.h b/Marlin/src/config/examples/RigidBot/Configuration_adv.h
index 8fb959d9558c0b62bb06793c0d71f28861a04a88..07aec7ba2b19adeb375d06b8d065d05a3318a506 100644
--- a/Marlin/src/config/examples/RigidBot/Configuration_adv.h
+++ b/Marlin/src/config/examples/RigidBot/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/SCARA/Configuration_adv.h b/Marlin/src/config/examples/SCARA/Configuration_adv.h
index c92fd9e516384c7eca5f5cf1ec18a6fff740776e..a4acbe7451d6f479078a6b20d593b93fd37bb059 100644
--- a/Marlin/src/config/examples/SCARA/Configuration_adv.h
+++ b/Marlin/src/config/examples/SCARA/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h b/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
index 792581ac39efaf16258553aa5352d59b9fa16877..748ad56cc1f4968506d3a935e58709eacc2629c2 100644
--- a/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
+++ b/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/TheBorg/Configuration_adv.h b/Marlin/src/config/examples/TheBorg/Configuration_adv.h
index 130a206df3b05f9ca4172714445c26aa7af785e1..5d2174392b2badf0e67066514c6f03d8289aa494 100644
--- a/Marlin/src/config/examples/TheBorg/Configuration_adv.h
+++ b/Marlin/src/config/examples/TheBorg/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h b/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
index 1d00bb98f6e954d644c512b3275a70db0a986713..bcc937adb90965c6cdbbca8c07a6d06afbf26a29 100644
--- a/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
+++ b/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h
index d0f05fc457c0517c263ad3ace9c38de52865c3ab..3810c8b5e2196b56883489b7945266490a313e3f 100644
--- a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h
+++ b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h b/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h
index aa67b785e817e473c4955d409062ab02d6b8a539..a2ce5a6f25965bb301c287a9059910d3a64a60da 100644
--- a/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h
+++ b/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h
@@ -934,6 +934,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h b/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h
index 0e85b1c265af7067003f17c1506491df5f87527f..29fe875445b0d2a8d9144c32705030ab21ec6932 100644
--- a/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h
+++ b/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
index c170f70cb12e9d8bb7a723fcf12f7a946280cd4a..56f9ae72005289738dd5ccabfd595def3098186b 100644
--- a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
+++ b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
@@ -923,6 +923,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
index 0cb146a0e55d2fff6576a7d8f67e9a7b028d0995..afc105cc52a2a83a1b2fe4c9cadb9015a24b989f 100644
--- a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
@@ -923,6 +923,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h
index 985cceb138eb404748a047891e8d4cf2911f5bdb..7b506478e389d9ccb2baf46c98bae6474896cc05 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h
@@ -923,6 +923,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
index 4d754cadca51be51411acdb6a488ee78366ad6aa..23804dea008465a5daec93ba0de30eea08f6a1e4 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
@@ -923,6 +923,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/delta/generic/Configuration_adv.h b/Marlin/src/config/examples/delta/generic/Configuration_adv.h
index 4d754cadca51be51411acdb6a488ee78366ad6aa..23804dea008465a5daec93ba0de30eea08f6a1e4 100644
--- a/Marlin/src/config/examples/delta/generic/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/generic/Configuration_adv.h
@@ -923,6 +923,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
index 4d754cadca51be51411acdb6a488ee78366ad6aa..23804dea008465a5daec93ba0de30eea08f6a1e4 100644
--- a/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
@@ -923,6 +923,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
index 229e481f6193498167f0e657acb097a0435e9188..2d9447ca56a208abd6157ed9f6a385e767cf4cb8 100644
--- a/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
@@ -928,6 +928,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
index 093a32f8942b54b7c525ec55b1b58a1a34886a74..d556d2f8c6aadc2c280374285a306efb3d1ebef4 100644
--- a/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
@@ -923,6 +923,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
index 90a3e21d76f4de8a21f51359aa2dc196e0b494a8..0b9cdd11fc11234b2503fe021af0e447f6ca7814 100644
--- a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
+++ b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/makibox/Configuration_adv.h b/Marlin/src/config/examples/makibox/Configuration_adv.h
index c2155e044e9427ab28d1e3071e84b2c3ebb1b58d..2b9695a553bf7a5a10915a961cb7e7a706b7e8f1 100644
--- a/Marlin/src/config/examples/makibox/Configuration_adv.h
+++ b/Marlin/src/config/examples/makibox/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h b/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h
index fead46d4b263f345dcf7384ad7b644cf163d950b..e6cf254a920adad61fb77cf892eb65dc40af53a8 100644
--- a/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h
+++ b/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h
@@ -921,6 +921,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/config/examples/wt150/Configuration_adv.h b/Marlin/src/config/examples/wt150/Configuration_adv.h
index 84599d7429fe5b40e9ce548613d5830f314db5d8..da93d4f269619b5bc596d5dd57f125896f479928 100644
--- a/Marlin/src/config/examples/wt150/Configuration_adv.h
+++ b/Marlin/src/config/examples/wt150/Configuration_adv.h
@@ -922,6 +922,7 @@
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
diff --git a/Marlin/src/feature/pause.cpp b/Marlin/src/feature/pause.cpp
index ba28e0f571922ec7a81e081b72f4c68a42aec5b1..0c5b7429347644baea8daa3f4a5f1aa60f87b797 100644
--- a/Marlin/src/feature/pause.cpp
+++ b/Marlin/src/feature/pause.cpp
@@ -187,37 +187,53 @@ bool load_filament(const float &load_length/*=0*/, const float &purge_length/*=0
// Load filament
if (load_length) do_pause_e_move(load_length, FILAMENT_CHANGE_LOAD_FEEDRATE);
- do {
- if (purge_length > 0) {
- // "Wait for filament purge"
- #if ENABLED(ULTIPANEL)
- if (show_lcd)
- lcd_advanced_pause_show_message(ADVANCED_PAUSE_MESSAGE_PURGE, mode);
- #endif
-
- // Extrude filament to get into hotend
- do_pause_e_move(purge_length, ADVANCED_PAUSE_EXTRUDE_FEEDRATE);
- }
+ #if ENABLED(ADVANCED_PAUSE_CONTINUOUS_PURGE)
- // Show "Purge More" / "Resume" menu and wait for reply
#if ENABLED(ULTIPANEL)
- if (show_lcd) {
- KEEPALIVE_STATE(PAUSED_FOR_USER);
- wait_for_user = false;
- lcd_advanced_pause_show_message(ADVANCED_PAUSE_MESSAGE_OPTION, mode);
- while (advanced_pause_menu_response == ADVANCED_PAUSE_RESPONSE_WAIT_FOR) idle(true);
- KEEPALIVE_STATE(IN_HANDLER);
- }
+ if (show_lcd)
+ lcd_advanced_pause_show_message(ADVANCED_PAUSE_MESSAGE_CONTINUOUS_PURGE);
#endif
- // Keep looping if "Purge More" was selected
- } while (
- #if ENABLED(ULTIPANEL)
- show_lcd && advanced_pause_menu_response == ADVANCED_PAUSE_RESPONSE_EXTRUDE_MORE
- #else
- 0
- #endif
- );
+ wait_for_user = true;
+ for (float purge_count = purge_length; purge_count > 0 && wait_for_user; --purge_count)
+ do_pause_e_move(1, ADVANCED_PAUSE_EXTRUDE_FEEDRATE);
+ wait_for_user = false;
+
+ #else
+
+ do {
+ if (purge_length > 0) {
+ // "Wait for filament purge"
+ #if ENABLED(ULTIPANEL)
+ if (show_lcd)
+ lcd_advanced_pause_show_message(ADVANCED_PAUSE_MESSAGE_PURGE, mode);
+ #endif
+
+ // Extrude filament to get into hotend
+ do_pause_e_move(purge_length, ADVANCED_PAUSE_EXTRUDE_FEEDRATE);
+ }
+
+ // Show "Purge More" / "Resume" menu and wait for reply
+ #if ENABLED(ULTIPANEL)
+ if (show_lcd) {
+ KEEPALIVE_STATE(PAUSED_FOR_USER);
+ wait_for_user = false;
+ lcd_advanced_pause_show_message(ADVANCED_PAUSE_MESSAGE_OPTION, mode);
+ while (advanced_pause_menu_response == ADVANCED_PAUSE_RESPONSE_WAIT_FOR) idle(true);
+ KEEPALIVE_STATE(IN_HANDLER);
+ }
+ #endif
+
+ // Keep looping if "Purge More" was selected
+ } while (
+ #if ENABLED(ULTIPANEL)
+ show_lcd && advanced_pause_menu_response == ADVANCED_PAUSE_RESPONSE_EXTRUDE_MORE
+ #else
+ 0
+ #endif
+ );
+
+ #endif
return true;
}
diff --git a/Marlin/src/feature/pause.h b/Marlin/src/feature/pause.h
index 5a1d03b291524246792b7d21897f65ffafcc49bb..b2e9e2709533b3475c5c9b93f39ff3beca29c4d9 100644
--- a/Marlin/src/feature/pause.h
+++ b/Marlin/src/feature/pause.h
@@ -44,6 +44,9 @@ enum AdvancedPauseMessage : char {
ADVANCED_PAUSE_MESSAGE_INSERT,
ADVANCED_PAUSE_MESSAGE_LOAD,
ADVANCED_PAUSE_MESSAGE_PURGE,
+ #if ENABLED(ADVANCED_PAUSE_CONTINUOUS_PURGE)
+ ADVANCED_PAUSE_MESSAGE_CONTINUOUS_PURGE,
+ #endif
ADVANCED_PAUSE_MESSAGE_OPTION,
ADVANCED_PAUSE_MESSAGE_RESUME,
ADVANCED_PAUSE_MESSAGE_STATUS,
diff --git a/Marlin/src/lcd/ultralcd.cpp b/Marlin/src/lcd/ultralcd.cpp
index 03495ab76dc551ebb1b4ea696b3dc4df31efa054..69c014280c9dab5cca23b8858fdf8373a5c1a108 100644
--- a/Marlin/src/lcd/ultralcd.cpp
+++ b/Marlin/src/lcd/ultralcd.cpp
@@ -218,14 +218,6 @@ uint16_t max_display_update_time = 0;
#else
void lcd_temp_menu_e0_filament_change();
#endif
- void lcd_advanced_pause_option_menu();
- void lcd_advanced_pause_init_message();
- void lcd_advanced_pause_unload_message();
- void lcd_advanced_pause_insert_message();
- void lcd_advanced_pause_load_message();
- void lcd_advanced_pause_heat_nozzle();
- void lcd_advanced_pause_purge_message();
- void lcd_advanced_pause_resume_message();
#endif
#if ENABLED(DAC_STEPPER_CURRENT)
@@ -4598,10 +4590,35 @@ void kill_screen(const char* lcd_msg) {
#if LCD_HEIGHT > _FC_LINES_G + 1
STATIC_ITEM(" ");
#endif
- HOTEND_STATUS_ITEM();
+ HOTEND_STATUS_ITEM();
END_SCREEN();
}
+ #if ENABLED(ADVANCED_PAUSE_CONTINUOUS_PURGE)
+ void lcd_advanced_pause_continuous_purge_menu() {
+ START_SCREEN();
+ STATIC_ITEM(MSG_FILAMENT_CHANGE_PURGE_1);
+ #ifdef MSG_FILAMENT_CHANGE_PURGE_2
+ STATIC_ITEM(MSG_FILAMENT_CHANGE_PURGE_2);
+ #define __FC_LINES_G 3
+ #else
+ #define __FC_LINES_G 2
+ #endif
+ #ifdef MSG_FILAMENT_CHANGE_PURGE_3
+ STATIC_ITEM(MSG_FILAMENT_CHANGE_PURGE_3);
+ #define _FC_LINES_G (__FC_LINES_G + 1)
+ #else
+ #define _FC_LINES_G __FC_LINES_G
+ #endif
+ #if LCD_HEIGHT > _FC_LINES_G + 1
+ STATIC_ITEM(" ");
+ #endif
+ HOTEND_STATUS_ITEM();
+ STATIC_ITEM(MSG_USERWAIT);
+ END_SCREEN();
+ }
+ #endif
+
void lcd_advanced_pause_resume_message() {
START_SCREEN();
STATIC_ITEM_P(advanced_pause_header(), true, true);
@@ -4627,6 +4644,9 @@ void kill_screen(const char* lcd_msg) {
case ADVANCED_PAUSE_MESSAGE_WAIT_FOR_NOZZLES_TO_HEAT: return lcd_advanced_pause_wait_for_nozzles_to_heat;
case ADVANCED_PAUSE_MESSAGE_OPTION: advanced_pause_menu_response = ADVANCED_PAUSE_RESPONSE_WAIT_FOR;
return lcd_advanced_pause_option_menu;
+ #if ENABLED(ADVANCED_PAUSE_CONTINUOUS_PURGE)
+ case ADVANCED_PAUSE_MESSAGE_CONTINUOUS_PURGE: return lcd_advanced_pause_continuous_purge_menu;
+ #endif
case ADVANCED_PAUSE_MESSAGE_STATUS:
default: break;
}