diff --git a/Marlin/Conditionals.h b/Marlin/Conditionals.h
new file mode 100644
index 0000000000000000000000000000000000000000..fc6d6573ea32d6c56caa741abafebeb8436c769d
--- /dev/null
+++ b/Marlin/Conditionals.h
@@ -0,0 +1,405 @@
+/**
+ * Conditionals.h
+ * Defines that depend on configuration but are not editable.
+ */
+#ifndef CONDITIONALS_H
+
+#ifndef CONFIGURATION_LCD // Get the LCD defines which are needed first
+
+ #define CONFIGURATION_LCD
+
+ #if defined(MAKRPANEL)
+ #define DOGLCD
+ #define SDSUPPORT
+ #define DEFAULT_LCD_CONTRAST 17
+ #define ULTIPANEL
+ #define NEWPANEL
+ #endif
+
+ #if defined(miniVIKI) || defined(VIKI2)
+ #define ULTRA_LCD //general LCD support, also 16x2
+ #define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
+ #define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
+
+ #ifdef miniVIKI
+ #define DEFAULT_LCD_CONTRAST 95
+ #else
+ #define DEFAULT_LCD_CONTRAST 40
+ #endif
+
+ #define ENCODER_PULSES_PER_STEP 4
+ #define ENCODER_STEPS_PER_MENU_ITEM 1
+ #endif
+
+ #ifdef PANEL_ONE
+ #define SDSUPPORT
+ #define ULTIMAKERCONTROLLER
+ #endif
+
+ #ifdef REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+ #define DOGLCD
+ #define U8GLIB_ST7920
+ #define REPRAP_DISCOUNT_SMART_CONTROLLER
+ #endif
+
+ #if defined(ULTIMAKERCONTROLLER) || defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL)
+ #define ULTIPANEL
+ #define NEWPANEL
+ #endif
+
+ #ifdef REPRAPWORLD_KEYPAD
+ #define ULTIPANEL
+ #define NEWPANEL
+ #endif
+
+ #ifdef RA_CONTROL_PANEL
+ #define LCD_I2C_TYPE_PCA8574
+ #define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander
+ #define ULTIPANEL
+ #define NEWPANEL
+ #endif
+
+ /**
+ * I2C PANELS
+ */
+
+ #ifdef LCD_I2C_SAINSMART_YWROBOT
+ // This uses the LiquidCrystal_I2C library ( https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home )
+ // Make sure it is placed in the Arduino libraries directory.
+ #define LCD_I2C_TYPE_PCF8575
+ #define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander
+ #define ULTIPANEL
+ #define NEWPANEL
+ #endif
+
+ // PANELOLU2 LCD with status LEDs, separate encoder and click inputs
+ #ifdef LCD_I2C_PANELOLU2
+ // This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
+ // Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
+ // (v1.2.3 no longer requires you to define PANELOLU in the LiquidTWI2.h library header file)
+ // Note: The PANELOLU2 encoder click input can either be directly connected to a pin
+ // (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
+ #define LCD_I2C_TYPE_MCP23017
+ #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
+ #define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD
+
+ #ifndef ENCODER_PULSES_PER_STEP
+ #define ENCODER_PULSES_PER_STEP 4
+ #endif
+
+ #ifndef ENCODER_STEPS_PER_MENU_ITEM
+ #define ENCODER_STEPS_PER_MENU_ITEM 1
+ #endif
+
+ #ifdef LCD_USE_I2C_BUZZER
+ #define LCD_FEEDBACK_FREQUENCY_HZ 1000
+ #define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
+ #endif
+
+ #define ULTIPANEL
+ #define NEWPANEL
+ #endif
+
+ // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
+ #ifdef LCD_I2C_VIKI
+ // This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
+ // Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
+ // Note: The pause/stop/resume LCD button pin should be connected to the Arduino
+ // BTN_ENC pin (or set BTN_ENC to -1 if not used)
+ #define LCD_I2C_TYPE_MCP23017
+ #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
+ #define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD (requires LiquidTWI2 v1.2.3 or later)
+ #define ULTIPANEL
+ #define NEWPANEL
+ #endif
+
+ // Shift register panels
+ // ---------------------
+ // 2 wire Non-latching LCD SR from:
+ // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
+
+ #ifdef SAV_3DLCD
+ #define SR_LCD_2W_NL // Non latching 2 wire shiftregister
+ #define ULTIPANEL
+ #define NEWPANEL
+ #endif
+
+
+ #ifdef ULTIPANEL
+ #define NEWPANEL //enable this if you have a click-encoder panel
+ #define SDSUPPORT
+ #define ULTRA_LCD
+ #ifdef DOGLCD // Change number of lines to match the DOG graphic display
+ #define LCD_WIDTH 22
+ #define LCD_HEIGHT 5
+ #else
+ #define LCD_WIDTH 20
+ #define LCD_HEIGHT 4
+ #endif
+ #else //no panel but just LCD
+ #ifdef ULTRA_LCD
+ #ifdef DOGLCD // Change number of lines to match the 128x64 graphics display
+ #define LCD_WIDTH 22
+ #define LCD_HEIGHT 5
+ #else
+ #define LCD_WIDTH 16
+ #define LCD_HEIGHT 2
+ #endif
+ #endif
+ #endif
+
+ /**
+ * Default LCD contrast for dogm-like LCD displays
+ */
+ #if defined(DOGLCD) && !defined(DEFAULT_LCD_CONTRAST)
+ #define DEFAULT_LCD_CONTRAST 32
+ #endif
+
+#else // CONFIGURATION_LCD
+
+ #define CONDITIONALS_H
+
+ #ifndef AT90USB
+ #define HardwareSerial_h // trick to disable the standard HWserial
+ #endif
+
+ #if (ARDUINO >= 100)
+ #include "Arduino.h"
+ #else
+ #include "WProgram.h"
+ #endif
+
+ #include "pins.h"
+
+ /**
+ * ENDSTOPPULLUPS
+ */
+ #ifdef ENDSTOPPULLUPS
+ #ifndef DISABLE_MAX_ENDSTOPS
+ #define ENDSTOPPULLUP_XMAX
+ #define ENDSTOPPULLUP_YMAX
+ #define ENDSTOPPULLUP_ZMAX
+ #endif
+ #ifndef DISABLE_MIN_ENDSTOPS
+ #define ENDSTOPPULLUP_XMIN
+ #define ENDSTOPPULLUP_YMIN
+ #define ENDSTOPPULLUP_ZMIN
+ #endif
+ #endif
+
+ /**
+ * Axis lengths
+ */
+ #define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
+ #define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
+ #define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
+
+ /**
+ * SCARA
+ */
+ #ifdef SCARA
+ #undef SLOWDOWN
+ #define QUICK_HOME //SCARA needs Quickhome
+ #endif
+
+ /**
+ * AUTOSET LOCATIONS OF LIMIT SWITCHES
+ * Added by ZetaPhoenix 09-15-2012
+ */
+ #ifdef MANUAL_HOME_POSITIONS // Use manual limit switch locations
+ #define X_HOME_POS MANUAL_X_HOME_POS
+ #define Y_HOME_POS MANUAL_Y_HOME_POS
+ #define Z_HOME_POS MANUAL_Z_HOME_POS
+ #else //!MANUAL_HOME_POSITIONS – Use home switch positions based on homing direction and travel limits
+ #ifdef BED_CENTER_AT_0_0
+ #define X_HOME_POS X_MAX_LENGTH * X_HOME_DIR * 0.5
+ #define Y_HOME_POS Y_MAX_LENGTH * Y_HOME_DIR * 0.5
+ #else
+ #define X_HOME_POS (X_HOME_DIR < 0 ? X_MIN_POS : X_MAX_POS)
+ #define Y_HOME_POS (Y_HOME_DIR < 0 ? Y_MIN_POS : Y_MAX_POS)
+ #endif
+ #define Z_HOME_POS (Z_HOME_DIR < 0 ? Z_MIN_POS : Z_MAX_POS)
+ #endif //!MANUAL_HOME_POSITIONS
+
+ /**
+ * Auto Bed Leveling
+ */
+ #ifdef ENABLE_AUTO_BED_LEVELING
+ // Boundaries for probing based on set limits
+ #define MIN_PROBE_X (max(X_MIN_POS, X_MIN_POS + X_PROBE_OFFSET_FROM_EXTRUDER))
+ #define MAX_PROBE_X (min(X_MAX_POS, X_MAX_POS + X_PROBE_OFFSET_FROM_EXTRUDER))
+ #define MIN_PROBE_Y (max(Y_MIN_POS, Y_MIN_POS + Y_PROBE_OFFSET_FROM_EXTRUDER))
+ #define MAX_PROBE_Y (min(Y_MAX_POS, Y_MAX_POS + Y_PROBE_OFFSET_FROM_EXTRUDER))
+ #endif
+
+ /**
+ * MAX_STEP_FREQUENCY differs for TOSHIBA
+ */
+ #ifdef CONFIG_STEPPERS_TOSHIBA
+ #define MAX_STEP_FREQUENCY 10000 // Max step frequency for Toshiba Stepper Controllers
+ #else
+ #define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)
+ #endif
+
+ // MS1 MS2 Stepper Driver Microstepping mode table
+ #define MICROSTEP1 LOW,LOW
+ #define MICROSTEP2 HIGH,LOW
+ #define MICROSTEP4 LOW,HIGH
+ #define MICROSTEP8 HIGH,HIGH
+ #define MICROSTEP16 HIGH,HIGH
+
+ /**
+ * Advance calculated values
+ */
+ #ifdef ADVANCE
+ #define EXTRUSION_AREA (0.25 * D_FILAMENT * D_FILAMENT * 3.14159)
+ #define STEPS_PER_CUBIC_MM_E (axis_steps_per_unit[E_AXIS] / EXTRUSION_AREA)
+ #endif
+
+ #ifdef ULTIPANEL
+ #undef SDCARDDETECTINVERTED
+ #endif
+
+ // Power Signal Control Definitions
+ // By default use ATX definition
+ #ifndef POWER_SUPPLY
+ #define POWER_SUPPLY 1
+ #endif
+ // 1 = ATX
+ #if (POWER_SUPPLY == 1)
+ #define PS_ON_AWAKE LOW
+ #define PS_ON_ASLEEP HIGH
+ #endif
+ // 2 = X-Box 360 203W
+ #if (POWER_SUPPLY == 2)
+ #define PS_ON_AWAKE HIGH
+ #define PS_ON_ASLEEP LOW
+ #endif
+
+ /**
+ * Temp Sensor defines
+ */
+ #if TEMP_SENSOR_0 == -2
+ #define HEATER_0_USES_MAX6675
+ #elif TEMP_SENSOR_0 == -1
+ #define HEATER_0_USES_AD595
+ #elif TEMP_SENSOR_0 == 0
+ #undef HEATER_0_MINTEMP
+ #undef HEATER_0_MAXTEMP
+ #elif TEMP_SENSOR_0 > 0
+ #define THERMISTORHEATER_0 TEMP_SENSOR_0
+ #define HEATER_0_USES_THERMISTOR
+ #endif
+
+ #if TEMP_SENSOR_1 == -1
+ #define HEATER_1_USES_AD595
+ #elif TEMP_SENSOR_1 == 0
+ #undef HEATER_1_MINTEMP
+ #undef HEATER_1_MAXTEMP
+ #elif TEMP_SENSOR_1 > 0
+ #define THERMISTORHEATER_1 TEMP_SENSOR_1
+ #define HEATER_1_USES_THERMISTOR
+ #endif
+
+ #if TEMP_SENSOR_2 == -1
+ #define HEATER_2_USES_AD595
+ #elif TEMP_SENSOR_2 == 0
+ #undef HEATER_2_MINTEMP
+ #undef HEATER_2_MAXTEMP
+ #elif TEMP_SENSOR_2 > 0
+ #define THERMISTORHEATER_2 TEMP_SENSOR_2
+ #define HEATER_2_USES_THERMISTOR
+ #endif
+
+ #if TEMP_SENSOR_3 == -1
+ #define HEATER_3_USES_AD595
+ #elif TEMP_SENSOR_3 == 0
+ #undef HEATER_3_MINTEMP
+ #undef HEATER_3_MAXTEMP
+ #elif TEMP_SENSOR_3 > 0
+ #define THERMISTORHEATER_3 TEMP_SENSOR_3
+ #define HEATER_3_USES_THERMISTOR
+ #endif
+
+ #if TEMP_SENSOR_BED == -1
+ #define BED_USES_AD595
+ #elif TEMP_SENSOR_BED == 0
+ #undef BED_MINTEMP
+ #undef BED_MAXTEMP
+ #elif TEMP_SENSOR_BED > 0
+ #define THERMISTORBED TEMP_SENSOR_BED
+ #define BED_USES_THERMISTOR
+ #endif
+
+ /**
+ * ARRAY_BY_EXTRUDERS based on EXTRUDERS
+ */
+ #if EXTRUDERS > 3
+ #define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1, v2, v3, v4 }
+ #elif EXTRUDERS > 2
+ #define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1, v2, v3 }
+ #elif EXTRUDERS > 1
+ #define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1, v2 }
+ #else
+ #define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1 }
+ #endif
+
+ /**
+ * Shorthand for pin tests, for temperature.cpp
+ */
+ #define HAS_TEMP_0 (defined(TEMP_0_PIN) && TEMP_0_PIN >= 0)
+ #define HAS_TEMP_1 (defined(TEMP_1_PIN) && TEMP_1_PIN >= 0)
+ #define HAS_TEMP_2 (defined(TEMP_2_PIN) && TEMP_2_PIN >= 0)
+ #define HAS_TEMP_3 (defined(TEMP_3_PIN) && TEMP_3_PIN >= 0)
+ #define HAS_TEMP_BED (defined(TEMP_BED_PIN) && TEMP_BED_PIN >= 0)
+ #define HAS_FILAMENT_SENSOR (defined(FILAMENT_SENSOR) && defined(FILWIDTH_PIN) && FILWIDTH_PIN >= 0)
+ #define HAS_HEATER_0 (defined(HEATER_0_PIN) && HEATER_0_PIN >= 0)
+ #define HAS_HEATER_1 (defined(HEATER_1_PIN) && HEATER_1_PIN >= 0)
+ #define HAS_HEATER_2 (defined(HEATER_2_PIN) && HEATER_2_PIN >= 0)
+ #define HAS_HEATER_3 (defined(HEATER_3_PIN) && HEATER_3_PIN >= 0)
+ #define HAS_HEATER_BED (defined(HEATER_BED_PIN) && HEATER_BED_PIN >= 0)
+ #define HAS_AUTO_FAN_0 (defined(EXTRUDER_0_AUTO_FAN_PIN) && EXTRUDER_0_AUTO_FAN_PIN >= 0)
+ #define HAS_AUTO_FAN_1 (defined(EXTRUDER_1_AUTO_FAN_PIN) && EXTRUDER_1_AUTO_FAN_PIN >= 0)
+ #define HAS_AUTO_FAN_2 (defined(EXTRUDER_2_AUTO_FAN_PIN) && EXTRUDER_2_AUTO_FAN_PIN >= 0)
+ #define HAS_AUTO_FAN_3 (defined(EXTRUDER_3_AUTO_FAN_PIN) && EXTRUDER_3_AUTO_FAN_PIN >= 0)
+ #define HAS_AUTO_FAN HAS_AUTO_FAN_0 || HAS_AUTO_FAN_1 || HAS_AUTO_FAN_2 || HAS_AUTO_FAN_3
+ #define HAS_FAN (defined(FAN_PIN) && FAN_PIN >= 0)
+
+ /**
+ * Helper Macros for heaters and extruder fan
+ */
+ #define WRITE_HEATER_0P(v) WRITE(HEATER_0_PIN, v)
+ #if EXTRUDERS > 1 || defined(HEATERS_PARALLEL)
+ #define WRITE_HEATER_1(v) WRITE(HEATER_1_PIN, v)
+ #if EXTRUDERS > 2
+ #define WRITE_HEATER_2(v) WRITE(HEATER_2_PIN, v)
+ #if EXTRUDERS > 3
+ #define WRITE_HEATER_3(v) WRITE(HEATER_3_PIN, v)
+ #endif
+ #endif
+ #endif
+ #ifdef HEATERS_PARALLEL
+ #define WRITE_HEATER_0(v) { WRITE_HEATER_0P(v); WRITE_HEATER_1(v); }
+ #else
+ #define WRITE_HEATER_0(v) WRITE_HEATER_0P(v)
+ #endif
+ #if HAS_HEATER_BED
+ #define WRITE_HEATER_BED(v) WRITE(HEATER_BED_PIN, v)
+ #endif
+ #if HAS_FAN
+ #define WRITE_FAN(v) WRITE(FAN_PIN, v)
+ #endif
+
+ /**
+ * Sampling period of the temperature routine
+ * This override comes originally from temperature.cpp
+ * The Configuration.h option is basically ignored.
+ */
+ #ifdef PID_dT
+ #undef PID_dT
+ #endif
+ #define PID_dT ((OVERSAMPLENR * 12.0)/(F_CPU / 64.0 / 256.0))
+
+
+#endif //CONFIGURATION_LCD
+#endif //CONDITIONALS_H