diff --git a/Marlin/src/config/examples/FlashForge/CreatorPro/Configuration_adv.h b/Marlin/src/config/examples/FlashForge/CreatorPro/Configuration_adv.h
index 1dc5c173a1da9885e822ca92759b21accc018bfc..044cc77cd7acc269e6fdc65312b7d9cecd73bb9f 100644
--- a/Marlin/src/config/examples/FlashForge/CreatorPro/Configuration_adv.h
+++ b/Marlin/src/config/examples/FlashForge/CreatorPro/Configuration_adv.h
@@ -77,6 +77,8 @@
   #define THERMAL_PROTECTION_PERIOD 40        // Seconds
   #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
 
+  //#define ADAPTIVE_FAN_SLOWING              // Slow part cooling fan if temperature drops
+
   /**
    * Whenever an M104, M109, or M303 increases the target temperature, the
    * firmware will wait for the WATCH_TEMP_PERIOD to expire. If the temperature
@@ -245,9 +247,6 @@
 #define CHAMBER_AUTO_FAN_PIN -1
 #define EXTRUDER_AUTO_FAN_TEMPERATURE 50
 #define EXTRUDER_AUTO_FAN_SPEED 255   // 255 == full speed
-//
-//#define E0_AUTO_FAN E0_AUTO_FAN_PIN
-//#define E1_AUTO_FAN E1_AUTO_FAN_PIN
 
 /**
  * Part-Cooling Fan Multiplexer
@@ -894,7 +893,6 @@
   #if ENABLED(MOVE_Z_WHEN_IDLE)
     #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
   #endif
-
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets
@@ -1488,22 +1486,6 @@
    */
   //#define TMC_DEBUG
 
-  /**
-   * M915 Z Axis Calibration
-   *
-   * - Adjust Z stepper current,
-   * - Drive the Z axis to its physical maximum, and
-   * - Home Z to account for the lost steps.
-   *
-   * Use M915 Snn to specify the current.
-   * Use M925 Znn to add extra Z height to Z_MAX_POS.
-   */
-  //#define TMC_Z_CALIBRATION
-  #if ENABLED(TMC_Z_CALIBRATION)
-    #define CALIBRATION_CURRENT 250
-    #define CALIBRATION_EXTRA_HEIGHT 10
-  #endif
-
   /**
    * You can set your own advanced settings by filling in predefined functions.
    * A list of available functions can be found on the library github page
@@ -1716,11 +1698,6 @@
  */
 //#define CNC_COORDINATE_SYSTEMS
 
-/**
- * M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
- */
-#define PINS_DEBUGGING
-
 /**
  * Auto-report temperatures with M155 S<seconds>
  */
@@ -1976,5 +1953,12 @@
   #define WIFI_PWD  "Wifi Password"
 #endif
 
+// @section develop
+
+/**
+ * M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
+ */
+//#define PINS_DEBUGGING
+
 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE