diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index e41bae29bbe2deb56a38bb86ca58d3517a3f5d8f..9e0970a56ef41d348622c850eba1215a2fa83b9c 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 89fde4a381ebcb2a2695848ead40d6a947c5df9d..51ae20c23c0f954290098526762f15a021725061 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/default/Configuration.h b/config/default/Configuration.h
index e41bae29bbe2deb56a38bb86ca58d3517a3f5d8f..9e0970a56ef41d348622c850eba1215a2fa83b9c 100644
--- a/config/default/Configuration.h
+++ b/config/default/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/default/Configuration_adv.h b/config/default/Configuration_adv.h
index 89fde4a381ebcb2a2695848ead40d6a947c5df9d..51ae20c23c0f954290098526762f15a021725061 100644
--- a/config/default/Configuration_adv.h
+++ b/config/default/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/3DFabXYZ/Migbot/Configuration.h b/config/examples/3DFabXYZ/Migbot/Configuration.h
index 54054be5a5cc44f5a570d0ce8778a23b5cccf675..d9f5d966812195fb95f667aebf2a2e6cf45d2c8a 100644
--- a/config/examples/3DFabXYZ/Migbot/Configuration.h
+++ b/config/examples/3DFabXYZ/Migbot/Configuration.h
@@ -936,7 +936,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 21, 61, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
index fbeb98112df4260bf81d745743a9a58cef11c367..ec952a8c106a63bcd677be1202365e96de9e9af7 100644
--- a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
+++ b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/ADIMLab/Gantry v1/Configuration.h b/config/examples/ADIMLab/Gantry v1/Configuration.h
index ca1196d4a28643a154319c47158dc26cdc07f3af..fd7dc6fee7fe21010e5f06731985fbffaabfb0f1 100644
--- a/config/examples/ADIMLab/Gantry v1/Configuration.h
+++ b/config/examples/ADIMLab/Gantry v1/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h
index c9040e7bf09d42a684d638db78095498c329a4e1..d5533b3865ea3209fdb1a1e31cb419ad9e63d0dd 100644
--- a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h
+++ b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/ADIMLab/Gantry v2/Configuration.h b/config/examples/ADIMLab/Gantry v2/Configuration.h
index ff7426793d23641e647609f59b2c45de6f881150..9a69fbbb114b5c5de2a4810a0c92fff0dcf15ba5 100644
--- a/config/examples/ADIMLab/Gantry v2/Configuration.h
+++ b/config/examples/ADIMLab/Gantry v2/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h
index 31511845dbd56667bcd8af31a05976f5080f394b..1277510223c2959793e4e8de1205c445b1d2a58e 100644
--- a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h
+++ b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/AlephObjects/TAZ4/Configuration.h b/config/examples/AlephObjects/TAZ4/Configuration.h
index 03cf1366d02623cd06d38d345af71e270269ec43..a986b7d7bd7791e3cfbcc77ed0e01f91c7ce38b7 100644
--- a/config/examples/AlephObjects/TAZ4/Configuration.h
+++ b/config/examples/AlephObjects/TAZ4/Configuration.h
@@ -949,7 +949,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -25, -29, -12.35 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/config/examples/AlephObjects/TAZ4/Configuration_adv.h
index 2307ec488b7bf53079f610848045c52ae1caac4d..cb92db45f22ca438f079d41702f5dcab27f4c492 100644
--- a/config/examples/AlephObjects/TAZ4/Configuration_adv.h
+++ b/config/examples/AlephObjects/TAZ4/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Alfawise/U20-bltouch/Configuration.h b/config/examples/Alfawise/U20-bltouch/Configuration.h
index 973c199c51fe2a4fc8dc21b4cf62baf7064585bd..748211698d6766061c6ef8af0026a6fbf14c7425 100644
--- a/config/examples/Alfawise/U20-bltouch/Configuration.h
+++ b/config/examples/Alfawise/U20-bltouch/Configuration.h
@@ -993,7 +993,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -35, -6, -0.5 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h
index ab7b26a075566bdb7e5163515dbcf521f1ce2651..92798c2ba23ea08195223e3728bb735f1e238ac4 100644
--- a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h
+++ b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h
@@ -1440,7 +1440,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Alfawise/U20/Configuration.h b/config/examples/Alfawise/U20/Configuration.h
index 90aa931ba80cd3e58453318c8bfa08614f41784f..823fb06b31a9b0340e694153c590f51cf6bee603 100644
--- a/config/examples/Alfawise/U20/Configuration.h
+++ b/config/examples/Alfawise/U20/Configuration.h
@@ -993,7 +993,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Alfawise/U20/Configuration_adv.h b/config/examples/Alfawise/U20/Configuration_adv.h
index 8a2dc21c1d116903d0fedb38c6bf6cfb6324cf37..18171008ad082135b3c078b9ac41d67c4bbfe775 100644
--- a/config/examples/Alfawise/U20/Configuration_adv.h
+++ b/config/examples/Alfawise/U20/Configuration_adv.h
@@ -1439,7 +1439,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/AliExpress/CL-260/Configuration.h b/config/examples/AliExpress/CL-260/Configuration.h
index 4d85f93949cd401592a6958212d85eea6de073f3..1ca93f33274e9e94355716bacec7944bd601c5de 100644
--- a/config/examples/AliExpress/CL-260/Configuration.h
+++ b/config/examples/AliExpress/CL-260/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/AliExpress/UM2pExt/Configuration.h b/config/examples/AliExpress/UM2pExt/Configuration.h
index 8c2f8174f280cec10e34a610d7e321be0cf33b3d..83781dc786e9943600474b0e2b4e3cb7ff5fa418 100644
--- a/config/examples/AliExpress/UM2pExt/Configuration.h
+++ b/config/examples/AliExpress/UM2pExt/Configuration.h
@@ -940,7 +940,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/AliExpress/UM2pExt/Configuration_adv.h b/config/examples/AliExpress/UM2pExt/Configuration_adv.h
index f4ce89776208a8d88fc703e991078e50074fb0bd..46dce0a029fc00e1fbc965a04d98dd92287671e5 100644
--- a/config/examples/AliExpress/UM2pExt/Configuration_adv.h
+++ b/config/examples/AliExpress/UM2pExt/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Anet/A2/Configuration.h b/config/examples/Anet/A2/Configuration.h
index 4f87aa4db524225bfa08bfb6468b2733dc6ce1f0..a1f7675646459a2d61695b279a2a468fcd795116 100644
--- a/config/examples/Anet/A2/Configuration.h
+++ b/config/examples/Anet/A2/Configuration.h
@@ -929,7 +929,8 @@
*/
//#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
//#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Anet/A2/Configuration_adv.h b/config/examples/Anet/A2/Configuration_adv.h
index b0ab2e110cbad63b8711ad04cc1728c883d85b70..6f82cbd22f237dc6a0b441d6f14905471e7c2df3 100644
--- a/config/examples/Anet/A2/Configuration_adv.h
+++ b/config/examples/Anet/A2/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Anet/A2plus/Configuration.h b/config/examples/Anet/A2plus/Configuration.h
index 05a08af759b586236a700e3be9c1dd14ac5f4b21..ce5e767b8deff41b5da0cd17f2913f371ae8ecdc 100644
--- a/config/examples/Anet/A2plus/Configuration.h
+++ b/config/examples/Anet/A2plus/Configuration.h
@@ -929,7 +929,8 @@
*/
//#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
//#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Anet/A2plus/Configuration_adv.h b/config/examples/Anet/A2plus/Configuration_adv.h
index b0ab2e110cbad63b8711ad04cc1728c883d85b70..6f82cbd22f237dc6a0b441d6f14905471e7c2df3 100644
--- a/config/examples/Anet/A2plus/Configuration_adv.h
+++ b/config/examples/Anet/A2plus/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Anet/A6/Configuration.h b/config/examples/Anet/A6/Configuration.h
index 57296bf1173f421530bd41236b191b9256c0baeb..6a04f1711c445b357d545a365f4ed4ee8a3efae1 100644
--- a/config/examples/Anet/A6/Configuration.h
+++ b/config/examples/Anet/A6/Configuration.h
@@ -983,7 +983,8 @@
// (mount: https://github.com/ralf-e/ANET_A6_modifications/tree/master/A6_X-Axis)
//#define NOZZLE_TO_PROBE_OFFSET { -30, 15, 0.75 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Anet/A6/Configuration_adv.h b/config/examples/Anet/A6/Configuration_adv.h
index 7b79eced0be984fee8124be7577e180268e5f2eb..db52dc08421eaee8851a994891acdbbd03087340 100644
--- a/config/examples/Anet/A6/Configuration_adv.h
+++ b/config/examples/Anet/A6/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Anet/A8/Configuration.h b/config/examples/Anet/A8/Configuration.h
index a6098e47f22e686717f88df8fd393b16532e5647..8d4644aa2c3a785247d7d514360ba4540f0cbf40 100644
--- a/config/examples/Anet/A8/Configuration.h
+++ b/config/examples/Anet/A8/Configuration.h
@@ -942,7 +942,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 0, 0, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Anet/A8/Configuration_adv.h b/config/examples/Anet/A8/Configuration_adv.h
index bef18b4cbee8d95dea73ae9108d0c41cb8af2330..81bcc7d90103a99c593b2a53d94a1eda468c1bec 100644
--- a/config/examples/Anet/A8/Configuration_adv.h
+++ b/config/examples/Anet/A8/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Anet/A8plus/Configuration.h b/config/examples/Anet/A8plus/Configuration.h
index d88ef28e1411f42a5da311790343b78c95607676..50a01a862a9143e7dd16310263851b9a3bb2da92 100644
--- a/config/examples/Anet/A8plus/Configuration.h
+++ b/config/examples/Anet/A8plus/Configuration.h
@@ -940,7 +940,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Anet/A8plus/Configuration_adv.h b/config/examples/Anet/A8plus/Configuration_adv.h
index e801585f6835f39e40138c602688dc6a52a3246a..0e34f1537d7d49da9ae585f9bb54e0d1ae8d17c4 100644
--- a/config/examples/Anet/A8plus/Configuration_adv.h
+++ b/config/examples/Anet/A8plus/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Anet/E16/Configuration.h b/config/examples/Anet/E16/Configuration.h
index c6ffb058084272b2f8e98947444b919d0ee3f3bf..111b9c864513fcb24c2fe415c8ededf9ea8be2d8 100644
--- a/config/examples/Anet/E16/Configuration.h
+++ b/config/examples/Anet/E16/Configuration.h
@@ -941,7 +941,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Anet/E16/Configuration_adv.h b/config/examples/Anet/E16/Configuration_adv.h
index 8bb24ed2a48f6bde5b77e0212106a933f9654c15..7a915181e78a4e2536984218f627ff994b91814d 100644
--- a/config/examples/Anet/E16/Configuration_adv.h
+++ b/config/examples/Anet/E16/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/AnyCubic/i3/Configuration.h b/config/examples/AnyCubic/i3/Configuration.h
index 3e14bc221b9d7af748169847b735832e6ce25cc2..46719efdfd0a9f5e4f0e20b6c3229a6cb1b84244 100644
--- a/config/examples/AnyCubic/i3/Configuration.h
+++ b/config/examples/AnyCubic/i3/Configuration.h
@@ -939,7 +939,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 75, 5, -2 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/AnyCubic/i3/Configuration_adv.h b/config/examples/AnyCubic/i3/Configuration_adv.h
index ad0564a31c55dffeee7dc94017348243cfda7b5c..3aff8fb86b8a1ef3224e81e6b8758af261186cf1 100644
--- a/config/examples/AnyCubic/i3/Configuration_adv.h
+++ b/config/examples/AnyCubic/i3/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/ArmEd/Configuration.h b/config/examples/ArmEd/Configuration.h
index f539452768662f045febd2dca537e32433a0233d..fe3283a26c08ecb816bfe99b7f5dd7b9ffc93f5a 100644
--- a/config/examples/ArmEd/Configuration.h
+++ b/config/examples/ArmEd/Configuration.h
@@ -930,7 +930,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/ArmEd/Configuration_adv.h b/config/examples/ArmEd/Configuration_adv.h
index 8f09133d494b38b827d0354ff25a89bb2d6fbe1d..fd7c29e8831151597527e082367de3064f653656 100644
--- a/config/examples/ArmEd/Configuration_adv.h
+++ b/config/examples/ArmEd/Configuration_adv.h
@@ -1442,7 +1442,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Azteeg/X5GT/Configuration.h b/config/examples/Azteeg/X5GT/Configuration.h
index 9730e1e2f64b66a84eedc0adf96bb741999e3edf..187c408d2fa5e0dd7cd5402294a33c8b70ecb252 100644
--- a/config/examples/Azteeg/X5GT/Configuration.h
+++ b/config/examples/Azteeg/X5GT/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration.h b/config/examples/BIBO/TouchX/cyclops/Configuration.h
index 10dc544f0113012fafff5221c73d1059eed1c289..e20bc5a51a705f81bd21778c23db937fb9535568 100644
--- a/config/examples/BIBO/TouchX/cyclops/Configuration.h
+++ b/config/examples/BIBO/TouchX/cyclops/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
index 9076a6c1d96ead8e05705deccb2b8b379552497b..483ff61e3b9bb4c4f167eb33c0cd07ad2dacc3c4 100644
--- a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
+++ b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/BIBO/TouchX/default/Configuration.h b/config/examples/BIBO/TouchX/default/Configuration.h
index 14fbb22722669d0237da2a0b7e46ae9cd2d70bb3..484d5efe0a2b88caae1a39114059efa1c1580fd4 100644
--- a/config/examples/BIBO/TouchX/default/Configuration.h
+++ b/config/examples/BIBO/TouchX/default/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/BIBO/TouchX/default/Configuration_adv.h b/config/examples/BIBO/TouchX/default/Configuration_adv.h
index 28fb50d5843fd0057080c0a0b148d2759552e759..a89a2ab7b3121b2c5644e64a6cbe798ed856d37a 100644
--- a/config/examples/BIBO/TouchX/default/Configuration_adv.h
+++ b/config/examples/BIBO/TouchX/default/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/BQ/Hephestos/Configuration.h b/config/examples/BQ/Hephestos/Configuration.h
index d907a758bb4a6689503313a796c37b8f2674a83a..5c599d4b4fc032793bd7573fdd49259280873c4b 100644
--- a/config/examples/BQ/Hephestos/Configuration.h
+++ b/config/examples/BQ/Hephestos/Configuration.h
@@ -917,7 +917,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -25, -29, -12.35 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/BQ/Hephestos/Configuration_adv.h b/config/examples/BQ/Hephestos/Configuration_adv.h
index 97a7af0cbdda5298e9608ef69b4b0c56a1338a0f..b7f19ea1039d4479168a597953f88c41c9169f90 100644
--- a/config/examples/BQ/Hephestos/Configuration_adv.h
+++ b/config/examples/BQ/Hephestos/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/BQ/Hephestos_2/Configuration.h b/config/examples/BQ/Hephestos_2/Configuration.h
index 5865eee9bdd09312486613f1ecb134cb3a6bc4a8..a8334abaafd905bae1b566a45f75046fb21a4ad8 100644
--- a/config/examples/BQ/Hephestos_2/Configuration.h
+++ b/config/examples/BQ/Hephestos_2/Configuration.h
@@ -930,7 +930,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 34, 15, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/BQ/Hephestos_2/Configuration_adv.h b/config/examples/BQ/Hephestos_2/Configuration_adv.h
index 778cf9589ac1f44a1a46d84e47ec5042cf8bb8af..1f56fdbe68e802d7ba727514dd01b76e74954e31 100644
--- a/config/examples/BQ/Hephestos_2/Configuration_adv.h
+++ b/config/examples/BQ/Hephestos_2/Configuration_adv.h
@@ -1446,7 +1446,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/BQ/WITBOX/Configuration.h b/config/examples/BQ/WITBOX/Configuration.h
index f42956985f27751f64697ab20228c3ef3d864f20..cf6a074c299d3a02a5e5d9b193812d5a9420f830 100644
--- a/config/examples/BQ/WITBOX/Configuration.h
+++ b/config/examples/BQ/WITBOX/Configuration.h
@@ -917,7 +917,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -25, -29, -12.35 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/BQ/WITBOX/Configuration_adv.h b/config/examples/BQ/WITBOX/Configuration_adv.h
index 97a7af0cbdda5298e9608ef69b4b0c56a1338a0f..b7f19ea1039d4479168a597953f88c41c9169f90 100644
--- a/config/examples/BQ/WITBOX/Configuration_adv.h
+++ b/config/examples/BQ/WITBOX/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration.h b/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration.h
index 54973430e51d35a43637e1e1417a309a1820becd..4df81eb6cab98756a0ffec5f37afd8c1088a71ca 100644
--- a/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration.h
+++ b/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration.h
@@ -921,7 +921,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration_adv.h b/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration_adv.h
index 911d523495a9a91ec1cbf8d0b01fd0715cc51811..57bffc921fc912d5bd2489522aed79e1b3c11e06 100644
--- a/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration_adv.h
+++ b/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration.h b/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration.h
index 431f52ec55511e54757adbd3c078b24b699c2563..3bcdcbde503c3f9423e16a1c310fc266215b5695 100644
--- a/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration.h
+++ b/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration.h
@@ -922,7 +922,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h b/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h
index 9a96777d038f45fe03a1900fe09cc0162270c55f..241e7df6c441e936a02e69252f1ffbb64b01d3fc 100644
--- a/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h
+++ b/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Cartesio/Configuration.h b/config/examples/Cartesio/Configuration.h
index ebd70b015b36e5e336fc17e4de907d3190285cae..4f3bd706f7ff132fefe81471ac968ff7de70af16 100644
--- a/config/examples/Cartesio/Configuration.h
+++ b/config/examples/Cartesio/Configuration.h
@@ -928,7 +928,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Cartesio/Configuration_adv.h b/config/examples/Cartesio/Configuration_adv.h
index f66fa189231cf02cdfe25449ae523976e6dbdc30..c1cafc135292596b2a7ccdbb1260a1cef6f433e7 100644
--- a/config/examples/Cartesio/Configuration_adv.h
+++ b/config/examples/Cartesio/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Creality/CR-10/Configuration.h b/config/examples/Creality/CR-10/Configuration.h
index 86589445f1aa28b4366d0a620ee0a3fb60be7a00..d72ae0b947329f8c0292518d8b9bba39d5c5dea3 100644
--- a/config/examples/Creality/CR-10/Configuration.h
+++ b/config/examples/Creality/CR-10/Configuration.h
@@ -939,7 +939,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Creality/CR-10/Configuration_adv.h b/config/examples/Creality/CR-10/Configuration_adv.h
index 51c846e4bb91d9d2c596bc8aa0fb6ceea6ca6380..c2f1070f3fad9e55e6aa984a21a2022539c6fd12 100644
--- a/config/examples/Creality/CR-10/Configuration_adv.h
+++ b/config/examples/Creality/CR-10/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Creality/CR-10S/Configuration.h b/config/examples/Creality/CR-10S/Configuration.h
index 6d188f4bae5b8dba3d050f1af06ff767dddd9032..580dfb846260fdad787dd1c3a2b8d0f7bc5981f6 100644
--- a/config/examples/Creality/CR-10S/Configuration.h
+++ b/config/examples/Creality/CR-10S/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Creality/CR-10S/Configuration_adv.h b/config/examples/Creality/CR-10S/Configuration_adv.h
index d230c148bf87d45bdca46e5bb8ffe6f65a70cd60..8e7af2eb868286dfed7ba0cc6d8aad9f3a380ae6 100644
--- a/config/examples/Creality/CR-10S/Configuration_adv.h
+++ b/config/examples/Creality/CR-10S/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Creality/CR-10_5S/Configuration.h b/config/examples/Creality/CR-10_5S/Configuration.h
index 6bde731076b6282f1161196fb6d38a81eaf09613..855c96a7a6c9e09f875d507b5cbfcd82a5e0442c 100644
--- a/config/examples/Creality/CR-10_5S/Configuration.h
+++ b/config/examples/Creality/CR-10_5S/Configuration.h
@@ -930,7 +930,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Creality/CR-10_5S/Configuration_adv.h b/config/examples/Creality/CR-10_5S/Configuration_adv.h
index e33311c9fd694924dc9e2d7a02a8956e5db3fe3b..2598d813eb00154a434f2c88fbd4156c1ce7d762 100644
--- a/config/examples/Creality/CR-10_5S/Configuration_adv.h
+++ b/config/examples/Creality/CR-10_5S/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Creality/CR-10mini/Configuration.h b/config/examples/Creality/CR-10mini/Configuration.h
index 4a9be92f49d587f7cfde2e9f845742bcbf9c5ff3..60f69a4311764afd93578235ff44f53864516107 100644
--- a/config/examples/Creality/CR-10mini/Configuration.h
+++ b/config/examples/Creality/CR-10mini/Configuration.h
@@ -948,7 +948,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Creality/CR-10mini/Configuration_adv.h b/config/examples/Creality/CR-10mini/Configuration_adv.h
index 8c6a5230a8901a3edf4a8881e9851026a60a131f..b94c9506a3c4aa462503b1199bebe5e06a0fbc73 100644
--- a/config/examples/Creality/CR-10mini/Configuration_adv.h
+++ b/config/examples/Creality/CR-10mini/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Creality/CR-20 Pro/Configuration.h b/config/examples/Creality/CR-20 Pro/Configuration.h
index 81754fe1cff0c8417aaea63f4d44334476b17950..628820bf38a7c07d0812121193e1bfc435bb1ab7 100644
--- a/config/examples/Creality/CR-20 Pro/Configuration.h
+++ b/config/examples/Creality/CR-20 Pro/Configuration.h
@@ -933,7 +933,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Creality/CR-20 Pro/Configuration_adv.h b/config/examples/Creality/CR-20 Pro/Configuration_adv.h
index 32499d22fec55bb31b02345b55d3e411a2d834f3..1a075bd6897dbd38ae46f0649604afdbc300ffcd 100644
--- a/config/examples/Creality/CR-20 Pro/Configuration_adv.h
+++ b/config/examples/Creality/CR-20 Pro/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Creality/CR-20/Configuration.h b/config/examples/Creality/CR-20/Configuration.h
index e92218aeedeeecd7eb1631741526a8e80bdbe0cb..b92ba8e549418d2c6beaff7204b850ee04800258 100644
--- a/config/examples/Creality/CR-20/Configuration.h
+++ b/config/examples/Creality/CR-20/Configuration.h
@@ -933,7 +933,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Creality/CR-20/Configuration_adv.h b/config/examples/Creality/CR-20/Configuration_adv.h
index 3e89bfe4456e6191317ef5f8dd7e6300c5ef283a..83f3eaa9d4c35d494e27df761674720cfdb196f5 100644
--- a/config/examples/Creality/CR-20/Configuration_adv.h
+++ b/config/examples/Creality/CR-20/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Creality/CR-8/Configuration.h b/config/examples/Creality/CR-8/Configuration.h
index 30da9c0064c6e6bc372ad354c5f8db51b2712c0a..1630b2cdeab7bbc5b7378c58eff6b4b99e8ba839 100644
--- a/config/examples/Creality/CR-8/Configuration.h
+++ b/config/examples/Creality/CR-8/Configuration.h
@@ -939,7 +939,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Creality/CR-8/Configuration_adv.h b/config/examples/Creality/CR-8/Configuration_adv.h
index 8281a0e3ca2aaaccbd5ed390387c427836d0d76b..863aaf71fd5d8942255ad3e202f6299208dd2d2c 100644
--- a/config/examples/Creality/CR-8/Configuration_adv.h
+++ b/config/examples/Creality/CR-8/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Creality/Ender-2/Configuration.h b/config/examples/Creality/Ender-2/Configuration.h
index 7733dbde6a61eb6c638a3a075550f447a674f742..d0dd66108866ef2f94536f783b9a05bc25414e53 100644
--- a/config/examples/Creality/Ender-2/Configuration.h
+++ b/config/examples/Creality/Ender-2/Configuration.h
@@ -933,7 +933,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Creality/Ender-2/Configuration_adv.h b/config/examples/Creality/Ender-2/Configuration_adv.h
index c64a3f1381db186e7010fe75b92a1c84fe13e5b8..8889d5aff9729358afa6d3898dd08cd4e9f607bd 100644
--- a/config/examples/Creality/Ender-2/Configuration_adv.h
+++ b/config/examples/Creality/Ender-2/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Creality/Ender-3/Configuration.h b/config/examples/Creality/Ender-3/Configuration.h
index b30dd1b807c28d1ea814a13592609e034ba6a3c3..4734c65509661755c58233d95e8f806fc9f6d48a 100644
--- a/config/examples/Creality/Ender-3/Configuration.h
+++ b/config/examples/Creality/Ender-3/Configuration.h
@@ -933,7 +933,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Creality/Ender-3/Configuration_adv.h b/config/examples/Creality/Ender-3/Configuration_adv.h
index 947c9627125e55ff9bf7e43cd0ce7c6624e758cc..8b2d5d8dff43e262d0c96038dba115249f94b0d6 100644
--- a/config/examples/Creality/Ender-3/Configuration_adv.h
+++ b/config/examples/Creality/Ender-3/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Creality/Ender-4/Configuration.h b/config/examples/Creality/Ender-4/Configuration.h
index 2e59277b4068abccc9f7fe0f24b15318a9db3c65..9cc53f8240d5ecb83e82a2b48d41efb08ea84cb2 100644
--- a/config/examples/Creality/Ender-4/Configuration.h
+++ b/config/examples/Creality/Ender-4/Configuration.h
@@ -939,7 +939,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Creality/Ender-4/Configuration_adv.h b/config/examples/Creality/Ender-4/Configuration_adv.h
index be06c5f339e7c8423cad3cf463011ebdd27cc606..17b3450e6156f64642466b210bfd0355d20e552d 100644
--- a/config/examples/Creality/Ender-4/Configuration_adv.h
+++ b/config/examples/Creality/Ender-4/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Creality/Ender-5 Pro/Configuration.h b/config/examples/Creality/Ender-5 Pro/Configuration.h
index 29cf2b18ab8f68ee43d988ea6deec7bf9616c065..b3585bf2c78cf1758a8bb87bdd3b79c7ce1d6b56 100644
--- a/config/examples/Creality/Ender-5 Pro/Configuration.h
+++ b/config/examples/Creality/Ender-5 Pro/Configuration.h
@@ -927,7 +927,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Creality/Ender-5 Pro/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/Configuration_adv.h
index 8e75e806f939571faa7c5913d453c02b3c953b66..a102d6aa3d02d80354a1e92c393d33068f6d533c 100644
--- a/config/examples/Creality/Ender-5 Pro/Configuration_adv.h
+++ b/config/examples/Creality/Ender-5 Pro/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Creality/Ender-5/Configuration.h b/config/examples/Creality/Ender-5/Configuration.h
index 517c4c825c3b84bf6969d12c29c5b629b9117a26..d23b4d551f220ca2484a0100938c871635906893 100644
--- a/config/examples/Creality/Ender-5/Configuration.h
+++ b/config/examples/Creality/Ender-5/Configuration.h
@@ -933,7 +933,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Creality/Ender-5/Configuration_adv.h b/config/examples/Creality/Ender-5/Configuration_adv.h
index bff7e382d45963e5cc96d9a174f30cbb7f166a06..92fec78d3277df5e12b3bbc27cbd6e804dc7807a 100644
--- a/config/examples/Creality/Ender-5/Configuration_adv.h
+++ b/config/examples/Creality/Ender-5/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration.h b/config/examples/Dagoma/Disco Ultimate/Configuration.h
index ac83ae9ba949d379769b79738ee73749eb6e052c..0c818a2a107740f617c09740cb6effcacf6c2a5a 100644
--- a/config/examples/Dagoma/Disco Ultimate/Configuration.h
+++ b/config/examples/Dagoma/Disco Ultimate/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 0, 21, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h
index 65d392c08adba61167d92c89ae6661c6e8f3e2eb..8a3cdf75a4bff7961dc9bab88cfc71101f8c8bde 100644
--- a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h
+++ b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration.h b/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration.h
index 9193daa2bd77cacb7fc6a37488f7b1fb1047c296..5ac11ac49c31c19814c2f2cd1c333b436ad22fa9 100644
--- a/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration.h
+++ b/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration.h
@@ -934,7 +934,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h b/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h
index 6ef3ec764e06c3f99dd628fa6131444c8edcfd01..80410efa4fc6ce135d569b10c1f37ef46e161b12 100755
--- a/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h
+++ b/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/EXP3D/Imprimante multifonction/Configuration.h b/config/examples/EXP3D/Imprimante multifonction/Configuration.h
index b6746dc2880f646bf3329b34da0662bae240e3aa..2e3beb74813baa0573eaa710eaddab068233aae9 100644
--- a/config/examples/EXP3D/Imprimante multifonction/Configuration.h
+++ b/config/examples/EXP3D/Imprimante multifonction/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -25, -29, -12.35 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 0
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h b/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h
index dc48787b4558fcd2f16e7a7d9f155bfd2329a88a..8313186c49964d4fd6967dfb259ae2d29912b018 100644
--- a/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h
+++ b/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Einstart-S/Configuration.h b/config/examples/Einstart-S/Configuration.h
index e1245dd0681c647624962d60c312e3fb3dffaafa..4646cbe141569f1f8be1b5e9d1e69e22cd0402ab 100644
--- a/config/examples/Einstart-S/Configuration.h
+++ b/config/examples/Einstart-S/Configuration.h
@@ -939,7 +939,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Einstart-S/Configuration_adv.h b/config/examples/Einstart-S/Configuration_adv.h
index e6e0f0666927e401012a85d6b55c1c0b997d1d69..373f22a6ed12992e49efb64594199984cbbe2bc5 100644
--- a/config/examples/Einstart-S/Configuration_adv.h
+++ b/config/examples/Einstart-S/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/FYSETC/AIO_II/Configuration.h b/config/examples/FYSETC/AIO_II/Configuration.h
index d725f89597686a4575135f591f35920bb28dad18..d66b1c8691a12e31ae1db5c93a039e48642af6f4 100644
--- a/config/examples/FYSETC/AIO_II/Configuration.h
+++ b/config/examples/FYSETC/AIO_II/Configuration.h
@@ -934,7 +934,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/FYSETC/AIO_II/Configuration_adv.h b/config/examples/FYSETC/AIO_II/Configuration_adv.h
index 2b76425131388066a0321b6ead5cb4bc79975788..146a35b1b1d22ea4a8c97e293b85fe0f11eb7de7 100644
--- a/config/examples/FYSETC/AIO_II/Configuration_adv.h
+++ b/config/examples/FYSETC/AIO_II/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h
index 501bf88412442664ea27498251fc2c3579150426..ed4cd1b40f39c621b9476150384627e9b16a7f10 100644
--- a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h
+++ b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h
@@ -934,7 +934,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -44, -6, -3.9 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h
index 13d10b475fc3db9dd5f6dbca802da3215e548a4c..d5ed737b2d3b98ccd81bd2c9d2ebebee233252bc 100644
--- a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h
+++ b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/FYSETC/Cheetah 1.2/base/Configuration.h b/config/examples/FYSETC/Cheetah 1.2/base/Configuration.h
index d8bdebb888124192d9bc1434ba53c5195010473c..3a075d3b68d85e806cc4e629531273ea6ec0c629 100644
--- a/config/examples/FYSETC/Cheetah 1.2/base/Configuration.h
+++ b/config/examples/FYSETC/Cheetah 1.2/base/Configuration.h
@@ -934,7 +934,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h b/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h
index 13d10b475fc3db9dd5f6dbca802da3215e548a4c..d5ed737b2d3b98ccd81bd2c9d2ebebee233252bc 100644
--- a/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h
+++ b/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/FYSETC/Cheetah/BLTouch/Configuration.h b/config/examples/FYSETC/Cheetah/BLTouch/Configuration.h
index fcc6f6c1c1d1ee486da49aae2b53553ee4c97bcb..dec2d704451679d78c41f01d73002c6b8314d38d 100644
--- a/config/examples/FYSETC/Cheetah/BLTouch/Configuration.h
+++ b/config/examples/FYSETC/Cheetah/BLTouch/Configuration.h
@@ -934,7 +934,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -44, -6, -3.9 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h b/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h
index 13d10b475fc3db9dd5f6dbca802da3215e548a4c..d5ed737b2d3b98ccd81bd2c9d2ebebee233252bc 100644
--- a/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h
+++ b/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/FYSETC/Cheetah/base/Configuration.h b/config/examples/FYSETC/Cheetah/base/Configuration.h
index 22d0f73a4382599e04a7bb926bae1f928518d742..f32e75f40ef6e0ebbff49b84f60da0a08d6be272 100644
--- a/config/examples/FYSETC/Cheetah/base/Configuration.h
+++ b/config/examples/FYSETC/Cheetah/base/Configuration.h
@@ -934,7 +934,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/FYSETC/Cheetah/base/Configuration_adv.h b/config/examples/FYSETC/Cheetah/base/Configuration_adv.h
index 13d10b475fc3db9dd5f6dbca802da3215e548a4c..d5ed737b2d3b98ccd81bd2c9d2ebebee233252bc 100644
--- a/config/examples/FYSETC/Cheetah/base/Configuration_adv.h
+++ b/config/examples/FYSETC/Cheetah/base/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/FYSETC/F6_13/Configuration.h b/config/examples/FYSETC/F6_13/Configuration.h
index 7dc08fa84b5627431afbced4dd3b70d944dc7630..4cbe4ffb22d93ebbe0d0105d82cef720f20ffde6 100644
--- a/config/examples/FYSETC/F6_13/Configuration.h
+++ b/config/examples/FYSETC/F6_13/Configuration.h
@@ -931,7 +931,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/FYSETC/F6_13/Configuration_adv.h b/config/examples/FYSETC/F6_13/Configuration_adv.h
index c53fe62c827a1a1e92a1ad06b21d61579f5e590f..617206e8b6d3f00152cef8600de623e78327fda7 100644
--- a/config/examples/FYSETC/F6_13/Configuration_adv.h
+++ b/config/examples/FYSETC/F6_13/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/FYSETC/S6/Configuration.h b/config/examples/FYSETC/S6/Configuration.h
index 6fbb938ebc1c788805478cf270bf2dfd86308b65..81c021b68a33efbc83c192926fa7c9b5df543733 100644
--- a/config/examples/FYSETC/S6/Configuration.h
+++ b/config/examples/FYSETC/S6/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/FYSETC/S6/Configuration_adv.h b/config/examples/FYSETC/S6/Configuration_adv.h
index 89fde4a381ebcb2a2695848ead40d6a947c5df9d..51ae20c23c0f954290098526762f15a021725061 100644
--- a/config/examples/FYSETC/S6/Configuration_adv.h
+++ b/config/examples/FYSETC/S6/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Felix/DUAL/Configuration.h b/config/examples/Felix/DUAL/Configuration.h
index abaca53b57a9f3ad6fc3aff5e2a3e95b29ad4857..1c1965be62f1ae0054aa4f94e4f532a5b737f025 100644
--- a/config/examples/Felix/DUAL/Configuration.h
+++ b/config/examples/Felix/DUAL/Configuration.h
@@ -910,7 +910,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -25, -29, -12.35 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Felix/DUAL/Configuration_adv.h b/config/examples/Felix/DUAL/Configuration_adv.h
index 11fd992048f84861a3f0f45141bfe65a9e9b2bf9..822ebca19fe31101a217cf4542aaa77b69ce858e 100644
--- a/config/examples/Felix/DUAL/Configuration_adv.h
+++ b/config/examples/Felix/DUAL/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Felix/Single/Configuration.h b/config/examples/Felix/Single/Configuration.h
index aadea5c3c6a8d926f30f5a175944a7b1d6de298c..665886a07ea39b7beb76c9417371bfdd8c0f2a21 100644
--- a/config/examples/Felix/Single/Configuration.h
+++ b/config/examples/Felix/Single/Configuration.h
@@ -910,7 +910,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -25, -29, -12.35 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Felix/Single/Configuration_adv.h b/config/examples/Felix/Single/Configuration_adv.h
index 11fd992048f84861a3f0f45141bfe65a9e9b2bf9..822ebca19fe31101a217cf4542aaa77b69ce858e 100644
--- a/config/examples/Felix/Single/Configuration_adv.h
+++ b/config/examples/Felix/Single/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/FlashForge/CreatorPro/Configuration.h b/config/examples/FlashForge/CreatorPro/Configuration.h
index d8b48ef8abc86ceb382f1df45d2a8239149cb572..842f80e0dcf131877edef376ee45efc86bc25725 100644
--- a/config/examples/FlashForge/CreatorPro/Configuration.h
+++ b/config/examples/FlashForge/CreatorPro/Configuration.h
@@ -921,7 +921,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/FlashForge/CreatorPro/Configuration_adv.h b/config/examples/FlashForge/CreatorPro/Configuration_adv.h
index 4c111fb16467b5564a36be51d21b4111c5f6d5fa..2346360a09388f6b22965e02f7b14fcb0d078400 100644
--- a/config/examples/FlashForge/CreatorPro/Configuration_adv.h
+++ b/config/examples/FlashForge/CreatorPro/Configuration_adv.h
@@ -1437,7 +1437,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/FolgerTech/i3-2020/Configuration.h b/config/examples/FolgerTech/i3-2020/Configuration.h
index 7d17d2c4cf63d0b8aca14114f0c910edb4b50939..601eb00a1bab91b34ec49d137735e19c0c03ae7d 100644
--- a/config/examples/FolgerTech/i3-2020/Configuration.h
+++ b/config/examples/FolgerTech/i3-2020/Configuration.h
@@ -935,7 +935,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 38, -7, -10.75 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 0
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/config/examples/FolgerTech/i3-2020/Configuration_adv.h
index c0b1b9cd323d5e7505b7383e9b79ac607aa3aea7..963b7f0d4d7fcc349dc210a05008f8bf81e69725 100644
--- a/config/examples/FolgerTech/i3-2020/Configuration_adv.h
+++ b/config/examples/FolgerTech/i3-2020/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Formbot/Raptor/Configuration.h b/config/examples/Formbot/Raptor/Configuration.h
index 7b76169c3cdd10ff39281fe5ab7869770f058e93..f764ec62b6a0abfdd2ea5dc5a90382444669c496 100644
--- a/config/examples/Formbot/Raptor/Configuration.h
+++ b/config/examples/Formbot/Raptor/Configuration.h
@@ -1014,7 +1014,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -22, 0, -1.5 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Formbot/Raptor/Configuration_adv.h b/config/examples/Formbot/Raptor/Configuration_adv.h
index e680b81a2e266a123122f4440ffaba8f85e9a8b9..9768e27f0c45b57d070aeabaff65c7cda3026a96 100644
--- a/config/examples/Formbot/Raptor/Configuration_adv.h
+++ b/config/examples/Formbot/Raptor/Configuration_adv.h
@@ -1440,7 +1440,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Formbot/T_Rex_2+/Configuration.h b/config/examples/Formbot/T_Rex_2+/Configuration.h
index 1e04fd26cc7a03916107f56ac008d1cf0fec1164..ba078cf844febad32ca6799954b530c9597e31a4 100644
--- a/config/examples/Formbot/T_Rex_2+/Configuration.h
+++ b/config/examples/Formbot/T_Rex_2+/Configuration.h
@@ -958,7 +958,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -3, 31, -1.25 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 0
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
index 61d538e4ac0447ca7d8de9de67506e529cdb7192..c18ffb21d2146445608401a3be582bac68556c25 100644
--- a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
+++ b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
@@ -1442,7 +1442,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Formbot/T_Rex_3/Configuration.h b/config/examples/Formbot/T_Rex_3/Configuration.h
index 271d3958aca66a22e55d96a4264b67f684080111..c45a5f17cd0f67004be50f5e2cd7474bcfd38359 100644
--- a/config/examples/Formbot/T_Rex_3/Configuration.h
+++ b/config/examples/Formbot/T_Rex_3/Configuration.h
@@ -941,7 +941,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -3, 31, -1.25 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 0
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Formbot/T_Rex_3/Configuration_adv.h b/config/examples/Formbot/T_Rex_3/Configuration_adv.h
index 4e27267d5319d3590100aff0314dfa2950207dcd..defa20c81aa243068385345cb24ce912155e1486 100644
--- a/config/examples/Formbot/T_Rex_3/Configuration_adv.h
+++ b/config/examples/Formbot/T_Rex_3/Configuration_adv.h
@@ -1442,7 +1442,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Geeetech/A10/Configuration.h b/config/examples/Geeetech/A10/Configuration.h
index 22043fb3e9278921f1e12e1800bee0fa41ff7e29..3d39a4560af4433b5c328e1ef153391f7d3d78c5 100644
--- a/config/examples/Geeetech/A10/Configuration.h
+++ b/config/examples/Geeetech/A10/Configuration.h
@@ -912,7 +912,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -37, 0, -3.6 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Geeetech/A10/Configuration_adv.h b/config/examples/Geeetech/A10/Configuration_adv.h
index f3bcef140425c1aa3abf6c0d53fa39237badc1d3..40a0d675cab1fee1306f5ce0b4cce3e931f9a015 100644
--- a/config/examples/Geeetech/A10/Configuration_adv.h
+++ b/config/examples/Geeetech/A10/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Geeetech/A10D/Configuration.h b/config/examples/Geeetech/A10D/Configuration.h
index 934ac4b83de48f22adc828599435e67d4e0b8a59..7aa308fc183b3ae5977db7d7d7ecf0dfe12151e6 100644
--- a/config/examples/Geeetech/A10D/Configuration.h
+++ b/config/examples/Geeetech/A10D/Configuration.h
@@ -911,7 +911,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -37, 0, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Geeetech/A10D/Configuration_adv.h b/config/examples/Geeetech/A10D/Configuration_adv.h
index e68ffbc5b7fc6149f9c34e227269f74b787263bf..4920c8a1707c77d899602cca37ac2cea339823ad 100644
--- a/config/examples/Geeetech/A10D/Configuration_adv.h
+++ b/config/examples/Geeetech/A10D/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Geeetech/A10M/Configuration.h b/config/examples/Geeetech/A10M/Configuration.h
index 99573fd620e5051515fea270406af9ad5938dd81..77d1a023f9e54e86e39c8761a5a39f65c678bd9d 100644
--- a/config/examples/Geeetech/A10M/Configuration.h
+++ b/config/examples/Geeetech/A10M/Configuration.h
@@ -912,7 +912,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -37, 0, -3.6 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Geeetech/A10M/Configuration_adv.h b/config/examples/Geeetech/A10M/Configuration_adv.h
index 6158b609e18983e52772edddec3cc1fae1b41433..1cba9d040d4a312faa503908c6a19fd937a09527 100644
--- a/config/examples/Geeetech/A10M/Configuration_adv.h
+++ b/config/examples/Geeetech/A10M/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Geeetech/A10T/Configuration.h b/config/examples/Geeetech/A10T/Configuration.h
index b22f80bb5398cc0ee3fafa4233f2929b8e5595d3..784227680d33436af16afaf55d0ea35701d3795e 100644
--- a/config/examples/Geeetech/A10T/Configuration.h
+++ b/config/examples/Geeetech/A10T/Configuration.h
@@ -912,7 +912,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -37, 0, -3.6 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Geeetech/A10T/Configuration_adv.h b/config/examples/Geeetech/A10T/Configuration_adv.h
index 6158b609e18983e52772edddec3cc1fae1b41433..1cba9d040d4a312faa503908c6a19fd937a09527 100644
--- a/config/examples/Geeetech/A10T/Configuration_adv.h
+++ b/config/examples/Geeetech/A10T/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Geeetech/A20/Configuration.h b/config/examples/Geeetech/A20/Configuration.h
index 342994f57062022d6e2f423f68a15605c6e64a96..602194fcaeee46d6055d2fe1a3dc088ed9a64e67 100644
--- a/config/examples/Geeetech/A20/Configuration.h
+++ b/config/examples/Geeetech/A20/Configuration.h
@@ -912,7 +912,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -37, 0, -3.6 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Geeetech/A20/Configuration_adv.h b/config/examples/Geeetech/A20/Configuration_adv.h
index 7d7100f3a7f654d211eaa8572a4dfc3553cdd536..2e77874ea76a9e7f6c3a69fcec42c385cff733b6 100644
--- a/config/examples/Geeetech/A20/Configuration_adv.h
+++ b/config/examples/Geeetech/A20/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Geeetech/A20M/Configuration.h b/config/examples/Geeetech/A20M/Configuration.h
index ca65f4fcbef2c2ace85f7a09135059025621b3cd..73e0ecf51722a2bcb7e91c21706b77eb0bd0fee9 100644
--- a/config/examples/Geeetech/A20M/Configuration.h
+++ b/config/examples/Geeetech/A20M/Configuration.h
@@ -912,7 +912,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -37, 0, -3.6 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Geeetech/A20M/Configuration_adv.h b/config/examples/Geeetech/A20M/Configuration_adv.h
index 7d7100f3a7f654d211eaa8572a4dfc3553cdd536..2e77874ea76a9e7f6c3a69fcec42c385cff733b6 100644
--- a/config/examples/Geeetech/A20M/Configuration_adv.h
+++ b/config/examples/Geeetech/A20M/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Geeetech/A20T/Configuration.h b/config/examples/Geeetech/A20T/Configuration.h
index 62a4f4ef48d13cbff2fb40d90790575b978e96fa..84196e64cb47cf49d3f336ecb5a6fb03bac94382 100644
--- a/config/examples/Geeetech/A20T/Configuration.h
+++ b/config/examples/Geeetech/A20T/Configuration.h
@@ -912,7 +912,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -37, 0, -3.6 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Geeetech/A20T/Configuration_adv.h b/config/examples/Geeetech/A20T/Configuration_adv.h
index 7d7100f3a7f654d211eaa8572a4dfc3553cdd536..2e77874ea76a9e7f6c3a69fcec42c385cff733b6 100644
--- a/config/examples/Geeetech/A20T/Configuration_adv.h
+++ b/config/examples/Geeetech/A20T/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Geeetech/A30/Configuration.h b/config/examples/Geeetech/A30/Configuration.h
index 81ea4e8702be56847e8414ec0d9b47e55a43f6f6..e9f07218b8cb3879bf3aa1f9de8095f91df19a41 100644
--- a/config/examples/Geeetech/A30/Configuration.h
+++ b/config/examples/Geeetech/A30/Configuration.h
@@ -912,7 +912,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 0
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Geeetech/A30/Configuration_adv.h b/config/examples/Geeetech/A30/Configuration_adv.h
index 11d193e02de6c1f66520d41e6fbb3f9198ee1fee..23311fe25936a8f578a14e7e2244c4a248a0a564 100644
--- a/config/examples/Geeetech/A30/Configuration_adv.h
+++ b/config/examples/Geeetech/A30/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Geeetech/E180/Configuration.h b/config/examples/Geeetech/E180/Configuration.h
index e020ccdfbbcfd177c0a3feb56dc8f2915d63a617..fca5dbbcca291a1e47720a7c12873db06bcee16d 100644
--- a/config/examples/Geeetech/E180/Configuration.h
+++ b/config/examples/Geeetech/E180/Configuration.h
@@ -913,7 +913,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 0
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Geeetech/E180/Configuration_adv.h b/config/examples/Geeetech/E180/Configuration_adv.h
index 11d193e02de6c1f66520d41e6fbb3f9198ee1fee..23311fe25936a8f578a14e7e2244c4a248a0a564 100644
--- a/config/examples/Geeetech/E180/Configuration_adv.h
+++ b/config/examples/Geeetech/E180/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Geeetech/GT2560/Configuration.h b/config/examples/Geeetech/GT2560/Configuration.h
index 0ec1d6fc9b23d6ba0dfb4343111873401f7f1d5c..8dcfd79c4320f2bea1df11a185ad6d0d3de38481 100644
--- a/config/examples/Geeetech/GT2560/Configuration.h
+++ b/config/examples/Geeetech/GT2560/Configuration.h
@@ -944,7 +944,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
index 0d39fd91a69d12764a4e0f36f44d24243d25ef2e..2cebcdb49dbec101b052a52181e7d7d7480ef6cd 100644
--- a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
+++ b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 8
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Geeetech/MeCreator2/Configuration.h b/config/examples/Geeetech/MeCreator2/Configuration.h
index f944c82e323a5f9b804ab794942f773459d91799..38da8c250233a45561bb13e824e50f84ae07541b 100644
--- a/config/examples/Geeetech/MeCreator2/Configuration.h
+++ b/config/examples/Geeetech/MeCreator2/Configuration.h
@@ -936,7 +936,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Geeetech/MeCreator2/Configuration_adv.h b/config/examples/Geeetech/MeCreator2/Configuration_adv.h
index d154552b87c55d96ca63f861a51a6d707ce0a61a..f8872120ff68f78ed57c21d9b49961806b8f974c 100644
--- a/config/examples/Geeetech/MeCreator2/Configuration_adv.h
+++ b/config/examples/Geeetech/MeCreator2/Configuration_adv.h
@@ -1437,7 +1437,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Geeetech/PI3A PRO/Configuration.h b/config/examples/Geeetech/PI3A PRO/Configuration.h
index bc7c82647ce7ab2bbddc9a5a822ecec756a752d4..340a9e2ae8b833834737896d0f57c1df118d9f8b 100644
--- a/config/examples/Geeetech/PI3A PRO/Configuration.h
+++ b/config/examples/Geeetech/PI3A PRO/Configuration.h
@@ -950,7 +950,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Geeetech/PI3A PRO/Configuration_adv.h b/config/examples/Geeetech/PI3A PRO/Configuration_adv.h
index 8dd178b0d1ebe362a11f7ce7d44f23a2bfbb4e20..a2e5c57678a3de2dd46c3a03bfbef571346db2ce 100644
--- a/config/examples/Geeetech/PI3A PRO/Configuration_adv.h
+++ b/config/examples/Geeetech/PI3A PRO/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h
index 3c53510e9367d64815307344d15e91da266b12b5..3605b83d4e4bb6010bb247316448ba007f176073 100644
--- a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h
+++ b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h
@@ -950,7 +950,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 4, -44, -1.4 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h
index 9c955f3d4993cefb092ffa128462f650a61a2b0f..5dae8bb1418a7c9b001a562c1a5c34c43069a520 100644
--- a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h
+++ b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h
@@ -949,7 +949,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h
index 5d0ed7e3b32990f80a5f2940ccbf3bd15b17d672..43a103be1025c4d6ddef413e7136ca5022d7e640 100644
--- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h
+++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
index f3bcef140425c1aa3abf6c0d53fa39237badc1d3..40a0d675cab1fee1306f5ce0b4cce3e931f9a015 100644
--- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
+++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h
index 9fd9cb1aeb1979196acc7596526d76b017238c93..b3a64b82bd74242b46965d3f3609adaf8bc12d1f 100644
--- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h
+++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
index f3bcef140425c1aa3abf6c0d53fa39237badc1d3..40a0d675cab1fee1306f5ce0b4cce3e931f9a015 100644
--- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
+++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/HMS434/Configuration.h b/config/examples/HMS434/Configuration.h
index 675144aabb0f8a15d2c4a6d0b1c103d43670ceda..5b809268f124ffd6bd4ce243335c5fbb43fca416 100644
--- a/config/examples/HMS434/Configuration.h
+++ b/config/examples/HMS434/Configuration.h
@@ -918,7 +918,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -21, 22, -1.54 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 20
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/HMS434/Configuration_adv.h b/config/examples/HMS434/Configuration_adv.h
index a3fd04a209e88c86764fe20033c2c9d7a44b4c21..ccf39ea4ccdea19de9495eba1cb25839405151bc 100644
--- a/config/examples/HMS434/Configuration_adv.h
+++ b/config/examples/HMS434/Configuration_adv.h
@@ -1430,7 +1430,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Infitary/i3-M508/Configuration.h b/config/examples/Infitary/i3-M508/Configuration.h
index fd631d176681b04e47cf907fad1c5530cc05ec35..869c99a0ba5a45731fd4bd69f72a56145b82524a 100644
--- a/config/examples/Infitary/i3-M508/Configuration.h
+++ b/config/examples/Infitary/i3-M508/Configuration.h
@@ -933,7 +933,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Infitary/i3-M508/Configuration_adv.h b/config/examples/Infitary/i3-M508/Configuration_adv.h
index 881f36690d6a0710fc7c5f08f2c788ddea9e7dea..a0d1e7dc0017714cf606e9d117f79f27f391d797 100644
--- a/config/examples/Infitary/i3-M508/Configuration_adv.h
+++ b/config/examples/Infitary/i3-M508/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/JGAurora/A1/Configuration.h b/config/examples/JGAurora/A1/Configuration.h
index d75903b33bdbab0d1c8ed817947d1687ecc51b7d..9c7a045a27000d36e05e33855976802082b2064b 100644
--- a/config/examples/JGAurora/A1/Configuration.h
+++ b/config/examples/JGAurora/A1/Configuration.h
@@ -936,7 +936,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/JGAurora/A1/Configuration_adv.h b/config/examples/JGAurora/A1/Configuration_adv.h
index 8ee59d4a5147bb20e21cf51d913948026831d971..64e76346fcc4c27e868f1eba85107c33793e663c 100644
--- a/config/examples/JGAurora/A1/Configuration_adv.h
+++ b/config/examples/JGAurora/A1/Configuration_adv.h
@@ -1443,7 +1443,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/JGAurora/A5/Configuration.h b/config/examples/JGAurora/A5/Configuration.h
index 39480ec57880ba659a7622a994477a049a9a71b4..ebd16205717f21432396be7af41e2f99e441560d 100644
--- a/config/examples/JGAurora/A5/Configuration.h
+++ b/config/examples/JGAurora/A5/Configuration.h
@@ -941,7 +941,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/JGAurora/A5/Configuration_adv.h b/config/examples/JGAurora/A5/Configuration_adv.h
index b295d41f83d2e42c94d5fb96ff4ff5319fbe9911..ebe19b2afb780659fabfcc182cfa972fed36db3f 100644
--- a/config/examples/JGAurora/A5/Configuration_adv.h
+++ b/config/examples/JGAurora/A5/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/JGAurora/A5S/Configuration.h b/config/examples/JGAurora/A5S/Configuration.h
index 0539ced6b1e2d3c10b9d2db173a7b314204a125f..722e3de8e88c07668bc447a1983f88c533af7499 100644
--- a/config/examples/JGAurora/A5S/Configuration.h
+++ b/config/examples/JGAurora/A5S/Configuration.h
@@ -936,7 +936,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/JGAurora/A5S/Configuration_adv.h b/config/examples/JGAurora/A5S/Configuration_adv.h
index 8ee59d4a5147bb20e21cf51d913948026831d971..64e76346fcc4c27e868f1eba85107c33793e663c 100644
--- a/config/examples/JGAurora/A5S/Configuration_adv.h
+++ b/config/examples/JGAurora/A5S/Configuration_adv.h
@@ -1443,7 +1443,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/MakerParts/Configuration.h b/config/examples/MakerParts/Configuration.h
index f9f771489bf4615ad527fd0b70d75af8b715bab7..1f8bd2286030211f36a74aebb7ec7fd365e819a0 100644
--- a/config/examples/MakerParts/Configuration.h
+++ b/config/examples/MakerParts/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/MakerParts/Configuration_adv.h b/config/examples/MakerParts/Configuration_adv.h
index 75069ef05977579d408339cbeb06fb3ff54253f0..5c63176b92e5a90ae4f6da2bec58eadf9d188419 100644
--- a/config/examples/MakerParts/Configuration_adv.h
+++ b/config/examples/MakerParts/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Malyan/M150/Configuration.h b/config/examples/Malyan/M150/Configuration.h
index 18449625676119eeaf6e667c30e1194703b94eaa..24e3d99749fb78817944ce5e93d82be813582dd0 100644
--- a/config/examples/Malyan/M150/Configuration.h
+++ b/config/examples/Malyan/M150/Configuration.h
@@ -953,7 +953,8 @@
// Note: HoolyHoo mount is X=35, Y=-50.
//#define NOZZLE_TO_PROBE_OFFSET { 35, -50, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Malyan/M150/Configuration_adv.h b/config/examples/Malyan/M150/Configuration_adv.h
index b759f46637eb5d7b8973fcf66254210df662ebe5..42bc1e48dd6d18c1be027e4d3d06dfe1f48069c7 100644
--- a/config/examples/Malyan/M150/Configuration_adv.h
+++ b/config/examples/Malyan/M150/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Malyan/M200/Configuration.h b/config/examples/Malyan/M200/Configuration.h
index 7b33b8831fdb808b8b07bac7efe814b9e64efc2b..b15aa6cdd067414e73763391086641061b3fbf79 100644
--- a/config/examples/Malyan/M200/Configuration.h
+++ b/config/examples/Malyan/M200/Configuration.h
@@ -939,7 +939,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Malyan/M200/Configuration_adv.h b/config/examples/Malyan/M200/Configuration_adv.h
index 3e582f61663f6db9f808c5e31ee443fed0d569ec..d9063388d53225259f1d95afe276089d18ada319 100644
--- a/config/examples/Malyan/M200/Configuration_adv.h
+++ b/config/examples/Malyan/M200/Configuration_adv.h
@@ -1440,7 +1440,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Micromake/C1/basic/Configuration.h b/config/examples/Micromake/C1/basic/Configuration.h
index e805a3d9099501697937dace87a528857e478056..84dee1ac2f77c868ceaa3014804a168dbfb75763 100644
--- a/config/examples/Micromake/C1/basic/Configuration.h
+++ b/config/examples/Micromake/C1/basic/Configuration.h
@@ -933,7 +933,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 0, 0, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Micromake/C1/enhanced/Configuration.h b/config/examples/Micromake/C1/enhanced/Configuration.h
index cf108832933dfba70beb9e0611d53c3ee2347c47..a77ee6809442ee6155083e3a5a761124001d2584 100644
--- a/config/examples/Micromake/C1/enhanced/Configuration.h
+++ b/config/examples/Micromake/C1/enhanced/Configuration.h
@@ -933,7 +933,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 0, 0, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/config/examples/Micromake/C1/enhanced/Configuration_adv.h
index 83058f81780b67a9cc81871bb93d138efa634559..1828ea598b13444057cb98a34bf7ec1241f71e63 100644
--- a/config/examples/Micromake/C1/enhanced/Configuration_adv.h
+++ b/config/examples/Micromake/C1/enhanced/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Mks/Robin/Configuration.h b/config/examples/Mks/Robin/Configuration.h
index cafdcc977bfff1d69e8e1aa1d4f3b94a32582c41..576825c46575056f7472cceb4580889f1dd39b93 100644
--- a/config/examples/Mks/Robin/Configuration.h
+++ b/config/examples/Mks/Robin/Configuration.h
@@ -930,7 +930,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Mks/Robin/Configuration_adv.h b/config/examples/Mks/Robin/Configuration_adv.h
index a4df446ff5caa48b601bd7400e6adf5fb5028a46..b230921518dbed4ab363351538d10d56b76fa233 100644
--- a/config/examples/Mks/Robin/Configuration_adv.h
+++ b/config/examples/Mks/Robin/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Mks/Robin_Lite3/Configuration.h b/config/examples/Mks/Robin_Lite3/Configuration.h
index 6bb626809a048fddaf8c9459a59f00385ff2044a..52c3efd7f8edfa89be0b51844c0d9c30a76b28c0 100644
--- a/config/examples/Mks/Robin_Lite3/Configuration.h
+++ b/config/examples/Mks/Robin_Lite3/Configuration.h
@@ -936,7 +936,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Mks/Robin_Pro/Configuration.h b/config/examples/Mks/Robin_Pro/Configuration.h
index 6b9895a241db1535e95eb7ce0267e5da90da77a7..987023b1722504e5037b827a0b2e19c453ba3a5a 100644
--- a/config/examples/Mks/Robin_Pro/Configuration.h
+++ b/config/examples/Mks/Robin_Pro/Configuration.h
@@ -935,7 +935,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Mks/Sbase/Configuration.h b/config/examples/Mks/Sbase/Configuration.h
index e98821c769b8bcee1e0dd6f4850f0e1ef6728bc3..e27654746360b5592c61f082a6a3e23cf25bb07b 100644
--- a/config/examples/Mks/Sbase/Configuration.h
+++ b/config/examples/Mks/Sbase/Configuration.h
@@ -928,7 +928,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 32, 5, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Mks/Sbase/Configuration_adv.h b/config/examples/Mks/Sbase/Configuration_adv.h
index 1790b4f6bf79edc6e9fc580dcd4bbb8fbd1d4c80..744836a827f41090e7d987fb4db097c66747ef64 100644
--- a/config/examples/Mks/Sbase/Configuration_adv.h
+++ b/config/examples/Mks/Sbase/Configuration_adv.h
@@ -1439,7 +1439,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Modix/Big60/Configuration.h b/config/examples/Modix/Big60/Configuration.h
index 82012b2778e30a0f20b0fccede7c534977ca67c0..5b5122b790a525768caf922321d7bb818fca9b34 100644
--- a/config/examples/Modix/Big60/Configuration.h
+++ b/config/examples/Modix/Big60/Configuration.h
@@ -928,7 +928,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -34, 26, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Modix/Big60/Configuration_adv.h b/config/examples/Modix/Big60/Configuration_adv.h
index 3e95e55eb8eb14d801c49817c6e7eab92a17f8cc..9b1556c4c01a65a9bed37cc34c2d8a67e5b27882 100644
--- a/config/examples/Modix/Big60/Configuration_adv.h
+++ b/config/examples/Modix/Big60/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Printrbot/PrintrboardG2/Configuration.h b/config/examples/Printrbot/PrintrboardG2/Configuration.h
index 41585db1e7b4a763a97867617fb92b723f55d386..de8355b4756db1bd08f69782827aab3a4f83f729 100644
--- a/config/examples/Printrbot/PrintrboardG2/Configuration.h
+++ b/config/examples/Printrbot/PrintrboardG2/Configuration.h
@@ -934,7 +934,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/RapideLite/RL200/Configuration.h b/config/examples/RapideLite/RL200/Configuration.h
index 10e8e08b3887dbf3179b6e31a39ae860e2e84e82..e83e9d3ba438fb783908a9119bb2033c4bbb3da4 100644
--- a/config/examples/RapideLite/RL200/Configuration.h
+++ b/config/examples/RapideLite/RL200/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/RapideLite/RL200/Configuration_adv.h b/config/examples/RapideLite/RL200/Configuration_adv.h
index c59a5104038db04faa681d781e254ad5332ad7d8..381376a7c950bae36a08f8778139456dc4e24b85 100644
--- a/config/examples/RapideLite/RL200/Configuration_adv.h
+++ b/config/examples/RapideLite/RL200/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Renkforce/RF100/Configuration.h b/config/examples/Renkforce/RF100/Configuration.h
index 59525cb6ef63c1ccc955c230e2318e30b9e2d01c..eb66859173567dd2a97d3736cbc5a2bffb3d7e4a 100644
--- a/config/examples/Renkforce/RF100/Configuration.h
+++ b/config/examples/Renkforce/RF100/Configuration.h
@@ -937,7 +937,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Renkforce/RF100/Configuration_adv.h b/config/examples/Renkforce/RF100/Configuration_adv.h
index f0a0214ce2aa3d4e74e3ac141a72bf5da4d5d866..90a6b06424b558f87dd82b721e479ab5fa3b5109 100644
--- a/config/examples/Renkforce/RF100/Configuration_adv.h
+++ b/config/examples/Renkforce/RF100/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Renkforce/RF100XL/Configuration.h b/config/examples/Renkforce/RF100XL/Configuration.h
index b12d288a586f87199512cffdb6d98d2111ce5962..92ccdc589297e40f0e40b2119cd7a65c470d6fd5 100644
--- a/config/examples/Renkforce/RF100XL/Configuration.h
+++ b/config/examples/Renkforce/RF100XL/Configuration.h
@@ -937,7 +937,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Renkforce/RF100XL/Configuration_adv.h b/config/examples/Renkforce/RF100XL/Configuration_adv.h
index f0a0214ce2aa3d4e74e3ac141a72bf5da4d5d866..90a6b06424b558f87dd82b721e479ab5fa3b5109 100644
--- a/config/examples/Renkforce/RF100XL/Configuration_adv.h
+++ b/config/examples/Renkforce/RF100XL/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Renkforce/RF100v2/Configuration.h b/config/examples/Renkforce/RF100v2/Configuration.h
index e53e7a6366753a22cd935f3e4629ffbbf38d1ce6..23e33076ebb88a6618e8c9910283af175014e04c 100644
--- a/config/examples/Renkforce/RF100v2/Configuration.h
+++ b/config/examples/Renkforce/RF100v2/Configuration.h
@@ -937,7 +937,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Renkforce/RF100v2/Configuration_adv.h b/config/examples/Renkforce/RF100v2/Configuration_adv.h
index f0a0214ce2aa3d4e74e3ac141a72bf5da4d5d866..90a6b06424b558f87dd82b721e479ab5fa3b5109 100644
--- a/config/examples/Renkforce/RF100v2/Configuration_adv.h
+++ b/config/examples/Renkforce/RF100v2/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/RepRapPro/Huxley/Configuration.h b/config/examples/RepRapPro/Huxley/Configuration.h
index ab0923ed5e966b5aaa33bd4d609c676205ea5b42..97faab78f2dcf048f8b83021ef6666c087739a92 100644
--- a/config/examples/RepRapPro/Huxley/Configuration.h
+++ b/config/examples/RepRapPro/Huxley/Configuration.h
@@ -969,7 +969,8 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/RepRapWorld/Megatronics/Configuration.h b/config/examples/RepRapWorld/Megatronics/Configuration.h
index 62e0980fa15f959ac02d10112687a7d08e051bc0..300098a0ba0ae0399d82b25ccc8261add455634a 100644
--- a/config/examples/RepRapWorld/Megatronics/Configuration.h
+++ b/config/examples/RepRapWorld/Megatronics/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -25, -29, -12.35 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/RigidBot/Configuration.h b/config/examples/RigidBot/Configuration.h
index 0eb2874e6fe49345264e627712f25a92033ae5db..662d64a62878ec17be7c88044424cc5aa499d574 100644
--- a/config/examples/RigidBot/Configuration.h
+++ b/config/examples/RigidBot/Configuration.h
@@ -927,7 +927,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -25, -29, -12.35 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/RigidBot/Configuration_adv.h b/config/examples/RigidBot/Configuration_adv.h
index 0baf66d89ce079d7da203aa04cda31bc0db4a31d..6fdcf1663b1d5c111162edb71d99975e9a5fd63c 100644
--- a/config/examples/RigidBot/Configuration_adv.h
+++ b/config/examples/RigidBot/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/SCARA/MP_SCARA/Configuration.h b/config/examples/SCARA/MP_SCARA/Configuration.h
index 1b9cec18f84553caf63ba3bf12315e133e908980..501f423c5212aebbf203974d2c1edfdd13eff85d 100644
--- a/config/examples/SCARA/MP_SCARA/Configuration.h
+++ b/config/examples/SCARA/MP_SCARA/Configuration.h
@@ -950,7 +950,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -25, -29, -12.35 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/SCARA/Morgan/Configuration.h b/config/examples/SCARA/Morgan/Configuration.h
index 39d319a142d60c91ae58abca88649c9debdf437e..e3fef4535f23eac2fb5b69282f2141e8b923a7a0 100644
--- a/config/examples/SCARA/Morgan/Configuration.h
+++ b/config/examples/SCARA/Morgan/Configuration.h
@@ -951,7 +951,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -25, -29, -12.35 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/SCARA/Morgan/Configuration_adv.h b/config/examples/SCARA/Morgan/Configuration_adv.h
index de72407033b1d96f141f579ec188f5ee59dcc97e..fc379612d11d254ae8b9a5a9aea143e42f71e39e 100644
--- a/config/examples/SCARA/Morgan/Configuration_adv.h
+++ b/config/examples/SCARA/Morgan/Configuration_adv.h
@@ -1435,7 +1435,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration.h b/config/examples/STM32/Black_STM32F407VET6/Configuration.h
index b0810f74475cd7053ef980a7c4f2540398eb1050..36dec613d48a787e281863704dd25796eec85122 100644
--- a/config/examples/STM32/Black_STM32F407VET6/Configuration.h
+++ b/config/examples/STM32/Black_STM32F407VET6/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
index 9a35e7412390cb12322835abdbddaf0d56688707..25717aa3ad2e4c12f67b22985f6a93c3e49b5617 100644
--- a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
+++ b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/STM32/STM32F103RE/Configuration.h b/config/examples/STM32/STM32F103RE/Configuration.h
index 66b1429a35a964528a242a6b623943499492cc5c..5faebd9378f7ea7ab73809c9a383ecc8443257cc 100644
--- a/config/examples/STM32/STM32F103RE/Configuration.h
+++ b/config/examples/STM32/STM32F103RE/Configuration.h
@@ -931,7 +931,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -25, -29, -12.35 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/STM32/STM32F4/Configuration.h b/config/examples/STM32/STM32F4/Configuration.h
index 71ab97a324dd617f6ce7e950358746e94cf3cf08..06f94ba678e6e31ee7ebae40b76e216caf827fa0 100644
--- a/config/examples/STM32/STM32F4/Configuration.h
+++ b/config/examples/STM32/STM32F4/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/STM32/stm32f103ret6/Configuration.h b/config/examples/STM32/stm32f103ret6/Configuration.h
index fcdab6c65485fc2b00ba2e298fe7ab2d7c3b0894..e9ddec40c2a141bd00fb189ef27c1a0647dde626 100644
--- a/config/examples/STM32/stm32f103ret6/Configuration.h
+++ b/config/examples/STM32/stm32f103ret6/Configuration.h
@@ -931,7 +931,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -25, -29, -12.35 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Sanguinololu/Configuration.h b/config/examples/Sanguinololu/Configuration.h
index 353faeb5aa970c956d75b40adf1e7405f7a69797..6cbe8444d44af6078330dd52dfa4114cbe97b1e6 100644
--- a/config/examples/Sanguinololu/Configuration.h
+++ b/config/examples/Sanguinololu/Configuration.h
@@ -960,7 +960,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Sanguinololu/Configuration_adv.h b/config/examples/Sanguinololu/Configuration_adv.h
index e041903f185d3331d111f7faff4f19adb7a28663..340f05649b0e0ae139c196c20dbb127371e671d4 100644
--- a/config/examples/Sanguinololu/Configuration_adv.h
+++ b/config/examples/Sanguinololu/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Tevo/Michelangelo/Configuration.h b/config/examples/Tevo/Michelangelo/Configuration.h
index fd82cb9d2ed429e979276941437b3f778d1996d1..d46f12241c83fab78697d03b9e59b60c58e57183 100644
--- a/config/examples/Tevo/Michelangelo/Configuration.h
+++ b/config/examples/Tevo/Michelangelo/Configuration.h
@@ -934,7 +934,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Tevo/Michelangelo/Configuration_adv.h b/config/examples/Tevo/Michelangelo/Configuration_adv.h
index 31988394f04599d9e0a739345b19fefa8a45984e..f2090dcc452f99a321ded010303de8eb2d26bbcd 100644
--- a/config/examples/Tevo/Michelangelo/Configuration_adv.h
+++ b/config/examples/Tevo/Michelangelo/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Tevo/Nereus/Configuration.h b/config/examples/Tevo/Nereus/Configuration.h
index 34c645f51f4604b3f563ba624c00a6fb004aa6f6..60453c4fc36a40970961c583ea177d6f45e844b2 100755
--- a/config/examples/Tevo/Nereus/Configuration.h
+++ b/config/examples/Tevo/Nereus/Configuration.h
@@ -913,7 +913,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Tevo/Nereus/Configuration_adv.h b/config/examples/Tevo/Nereus/Configuration_adv.h
index 8f77bdc0fda4625c13e33bc3d75caddabd1efdd3..74f194fc98f08a761b7f7fa0abfbf198e9ebe0a7 100755
--- a/config/examples/Tevo/Nereus/Configuration_adv.h
+++ b/config/examples/Tevo/Nereus/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Tevo/Tarantula Pro/Configuration.h b/config/examples/Tevo/Tarantula Pro/Configuration.h
index e136ca3af877055694df2de5bc88f8f348c1ec60..445bd31658f5be03f2c7c96d5bd2451b853d566c 100644
--- a/config/examples/Tevo/Tarantula Pro/Configuration.h
+++ b/config/examples/Tevo/Tarantula Pro/Configuration.h
@@ -934,7 +934,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 0, 18, -1.5 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h
index e0d4b3a49f2a419ab91e73217a69a21c756e0ecf..8b4842c921c455438605131aada8b5b003f3e2d5 100755
--- a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h
+++ b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h
index 18440fdf8a042c2414120171dee8539eec50e16c..fc0e16ea35df15d72e4347103a676dabceb74f1c 100644
--- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h
+++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h
@@ -934,7 +934,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -45, -12, -2.77 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h
index de736c3bb8585d369cea8226016b2cfaea90385a..e1598114351d277bfc953ab18d6485f922e253ac 100755
--- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h
+++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h
index 0f7fd9713490efaa056cee5bfc3aefe0e38fec06..b3b6674c976343ceab9fbfb15e0336be2b638776 100644
--- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h
+++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h
@@ -934,7 +934,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -45, -12, -2.77 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h
index de736c3bb8585d369cea8226016b2cfaea90385a..e1598114351d277bfc953ab18d6485f922e253ac 100755
--- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h
+++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/TheBorg/Configuration.h b/config/examples/TheBorg/Configuration.h
index 0a192c0e87bd7b71ca9d7187f225a5a9d48005e7..1343f7c980c1299b84505d6cc18bea8a338785fe 100644
--- a/config/examples/TheBorg/Configuration.h
+++ b/config/examples/TheBorg/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 32, 5, -1.3 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/TheBorg/Configuration_adv.h b/config/examples/TheBorg/Configuration_adv.h
index ae57c8a4d9dc1e94ed1dbbedabdf3256dd9a72c2..fdd2e96be04eb07947737cb75e9a647f53d7232d 100644
--- a/config/examples/TheBorg/Configuration_adv.h
+++ b/config/examples/TheBorg/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/TinyBoy2/Configuration.h b/config/examples/TinyBoy2/Configuration.h
index 72ace636065d856ad9be32a17e9ac614403dfba0..5b22f8246542615bdefcc20f89b18673f339bd7c 100644
--- a/config/examples/TinyBoy2/Configuration.h
+++ b/config/examples/TinyBoy2/Configuration.h
@@ -980,7 +980,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 34, 15, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/TinyBoy2/Configuration_adv.h b/config/examples/TinyBoy2/Configuration_adv.h
index 22f71e7fd6d8245c085584d885cdc67330cd1fa3..e54a0ef32717f3649fa7db06ce83a1aa0c5be361 100644
--- a/config/examples/TinyBoy2/Configuration_adv.h
+++ b/config/examples/TinyBoy2/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Tronxy/X1/Configuration.h b/config/examples/Tronxy/X1/Configuration.h
index 9ce7ae443850c97bb98313522a692f405ff5552c..8f441eabd9a38737948717e7135dac106aecf355 100644
--- a/config/examples/Tronxy/X1/Configuration.h
+++ b/config/examples/Tronxy/X1/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Tronxy/X3A/Configuration.h b/config/examples/Tronxy/X3A/Configuration.h
index c3302b0bccd5613f0d529c2ba312623b379a4111..7dcafa509c1e2dff418ffd159ea7a879b884f1b5 100644
--- a/config/examples/Tronxy/X3A/Configuration.h
+++ b/config/examples/Tronxy/X3A/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -32, -10, -0.5 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 50
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Tronxy/X3A/Configuration_adv.h b/config/examples/Tronxy/X3A/Configuration_adv.h
index 3dcf8ded324f00fc22dcf9728eaf8b81f4a9462b..ecc1800a184b893e9290ff66d7494d039f4c3297 100644
--- a/config/examples/Tronxy/X3A/Configuration_adv.h
+++ b/config/examples/Tronxy/X3A/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Tronxy/X5S-2E/Configuration.h b/config/examples/Tronxy/X5S-2E/Configuration.h
index e7cf88338bc2e1098a1bd6634559043b11cfb418..ec15e440be45feff9ce3cd6312ff98a4a566c978 100644
--- a/config/examples/Tronxy/X5S-2E/Configuration.h
+++ b/config/examples/Tronxy/X5S-2E/Configuration.h
@@ -950,7 +950,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Tronxy/X5S-2E/Configuration_adv.h b/config/examples/Tronxy/X5S-2E/Configuration_adv.h
index 12acd7e925ddb07ad662ad16977cc1b47d4ac6ee..ac2aa9ef3843d090724fe8c2939819ee5dafc1c8 100644
--- a/config/examples/Tronxy/X5S-2E/Configuration_adv.h
+++ b/config/examples/Tronxy/X5S-2E/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Tronxy/X5S/Configuration.h b/config/examples/Tronxy/X5S/Configuration.h
index 5a5496fc0209d0a97a2a73b4ba60c98eb395882a..bee413732564de3c3ef2dedb2ee87be7b3b3c57d 100644
--- a/config/examples/Tronxy/X5S/Configuration.h
+++ b/config/examples/Tronxy/X5S/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -45, -55, -0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Tronxy/XY100/Configuration.h b/config/examples/Tronxy/XY100/Configuration.h
index 80f61f2a3c64197a2321da4023372c5af8919f62..29c90326b75a18d00c8d03603d7ac228ebed319d 100644
--- a/config/examples/Tronxy/XY100/Configuration.h
+++ b/config/examples/Tronxy/XY100/Configuration.h
@@ -940,7 +940,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/UltiMachine/Archim1/Configuration.h b/config/examples/UltiMachine/Archim1/Configuration.h
index 488d8713b0562609d85c7ac79fa238eac363d2e6..8183ac02490f6f7879351b6bfe6d2c4b18b1a043 100644
--- a/config/examples/UltiMachine/Archim1/Configuration.h
+++ b/config/examples/UltiMachine/Archim1/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/UltiMachine/Archim1/Configuration_adv.h b/config/examples/UltiMachine/Archim1/Configuration_adv.h
index 3a96ad171d2ba4d781cbd7407a500e07be85dc94..33358ffa231c62f6324e41dc3efe5e2b9e9e1543 100644
--- a/config/examples/UltiMachine/Archim1/Configuration_adv.h
+++ b/config/examples/UltiMachine/Archim1/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/UltiMachine/Archim2/Configuration.h b/config/examples/UltiMachine/Archim2/Configuration.h
index 4e8e46d4095f2081ce54f13c3e31948edc913f99..2500e534a768c990c7842a0b04b4a7a801da8c76 100644
--- a/config/examples/UltiMachine/Archim2/Configuration.h
+++ b/config/examples/UltiMachine/Archim2/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/UltiMachine/Archim2/Configuration_adv.h b/config/examples/UltiMachine/Archim2/Configuration_adv.h
index bffab669922c292bad765d66ce05f68454f4b498..2e2b7f6cf743b9d80ea826fd51d4a4862dddfdc8 100644
--- a/config/examples/UltiMachine/Archim2/Configuration_adv.h
+++ b/config/examples/UltiMachine/Archim2/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/VORONDesign/Configuration.h b/config/examples/VORONDesign/Configuration.h
index a2c424a091ee2da09238c8ba15d73bb6285e233e..1b505bb90b2b38b3ad2fc28fa472ea7bf7fcca88 100644
--- a/config/examples/VORONDesign/Configuration.h
+++ b/config/examples/VORONDesign/Configuration.h
@@ -938,7 +938,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 0, 0, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/VORONDesign/Configuration_adv.h b/config/examples/VORONDesign/Configuration_adv.h
index b83cf5cab1d91115f5d401a958601f56ce404d7b..87ea702257784ffa530b0d3c6e421047c4568f8e 100644
--- a/config/examples/VORONDesign/Configuration_adv.h
+++ b/config/examples/VORONDesign/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Velleman/K8200/Configuration.h b/config/examples/Velleman/K8200/Configuration.h
index 1fc123a09742bc0c70ea5b06cff874310165415d..c71828697b7261aec40a46660faf59830908dd5c 100644
--- a/config/examples/Velleman/K8200/Configuration.h
+++ b/config/examples/Velleman/K8200/Configuration.h
@@ -958,7 +958,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Velleman/K8200/Configuration_adv.h b/config/examples/Velleman/K8200/Configuration_adv.h
index b1e7f197fc3d4aa02f446fc1a8c33bd42ee78891..8a6fdb4dc590833263531dcb0817de2a1ac78dc4 100644
--- a/config/examples/Velleman/K8200/Configuration_adv.h
+++ b/config/examples/Velleman/K8200/Configuration_adv.h
@@ -1451,7 +1451,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration.h b/config/examples/Velleman/K8400/Dual-head/Configuration.h
index 90c73e6a588584fa524ee84c205f50627eb45eef..94f5dde2dc6ae09d2f4315d6bdf6e5746eb89b22 100644
--- a/config/examples/Velleman/K8400/Dual-head/Configuration.h
+++ b/config/examples/Velleman/K8400/Dual-head/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h
index f800b5c4413c7ce752cb19cc29666839ffa02221..38c820ca533ed5dd67c8aa2369106f0f6f8463d3 100644
--- a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h
+++ b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Velleman/K8400/Single-head/Configuration.h b/config/examples/Velleman/K8400/Single-head/Configuration.h
index d93773dcd33fc05218c8882ea609f3559f1a9c72..5615f51f2b8e5a297c0b5f447c214fe7250f7397 100644
--- a/config/examples/Velleman/K8400/Single-head/Configuration.h
+++ b/config/examples/Velleman/K8400/Single-head/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h
index f800b5c4413c7ce752cb19cc29666839ffa02221..38c820ca533ed5dd67c8aa2369106f0f6f8463d3 100644
--- a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h
+++ b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/WASP/PowerWASP/Configuration.h b/config/examples/WASP/PowerWASP/Configuration.h
index 6c33f321eda823758eb56816a8d29e117a2b1502..c063560aff0c6b7eeb9d37870e22709a123e054c 100644
--- a/config/examples/WASP/PowerWASP/Configuration.h
+++ b/config/examples/WASP/PowerWASP/Configuration.h
@@ -948,7 +948,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/WASP/PowerWASP/Configuration_adv.h b/config/examples/WASP/PowerWASP/Configuration_adv.h
index 9495a5416c021f8039710a2367fb4ba91c79c818..3e4a91ae66388ff1a9f05a68c1211ddfa8c7cf46 100644
--- a/config/examples/WASP/PowerWASP/Configuration_adv.h
+++ b/config/examples/WASP/PowerWASP/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Wanhao/Duplicator 6/Configuration.h b/config/examples/Wanhao/Duplicator 6/Configuration.h
index ce6f61d543a51b191510f549e7145e0b95201831..ec7bef9f5a8674a44c2bfac711a209d15d0fac7d 100644
--- a/config/examples/Wanhao/Duplicator 6/Configuration.h
+++ b/config/examples/Wanhao/Duplicator 6/Configuration.h
@@ -939,7 +939,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
index 0f0f5072f603a38f75e38b1bfc63a35e7fec369c..0de6c70c366f3bcc59156cee7776b72f96135d3c 100644
--- a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
+++ b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
@@ -1440,7 +1440,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h
index b5c20b83d67b586997ab44ece64134a9755fc895..4bbecf904328a9c4e683faa8ffd1a50ce3d85a93 100644
--- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h
+++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h
@@ -940,7 +940,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h
index 6077e052507e7548df1df4f6ae7a365bdac5e6e8..937a17eb48f3038faf9f89787f34e56a99745009 100644
--- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h
+++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h
index 6dcd80acbf0c746dfaf8aeb1bb7b09e9c3563f6c..776a004da8486920c8f71057cf5b6f0f7cbfc380 100755
--- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h
+++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h
index 6ccfd6e73119e93b041e38e811ec020549f4f60d..5b157d4fe52bf0cc0dfe90d7f80b237929e391c0 100644
--- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h
+++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/adafruit/ST7565/Configuration.h b/config/examples/adafruit/ST7565/Configuration.h
index a95468960aa3fc4a62de9818a256c03d317dd746..81e22a0a563eb88b5bdce829e43d9fec0a6762fc 100644
--- a/config/examples/adafruit/ST7565/Configuration.h
+++ b/config/examples/adafruit/ST7565/Configuration.h
@@ -929,7 +929,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -25, -29, -12.35 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/delta/Anycubic/Kossel/Configuration.h b/config/examples/delta/Anycubic/Kossel/Configuration.h
index 7fc6822a2e2d37ff64f253e554d275607a7b6a3d..8d86f8b27bdfa92e2f4ee62505a82fc6c6c56115 100644
--- a/config/examples/delta/Anycubic/Kossel/Configuration.h
+++ b/config/examples/delta/Anycubic/Kossel/Configuration.h
@@ -1092,7 +1092,8 @@
#define NOZZLE_TO_PROBE_OFFSET { 0, 0, 0 }
#endif
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 15
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h
index b702538b7c8da91f98094f45a22571ed0dfee5e3..2bc966647966aafa20fe3a12bc2b70842be21b40 100644
--- a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h
+++ b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h
@@ -1440,7 +1440,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration.h b/config/examples/delta/Dreammaker/Overlord/Configuration.h
index f6d828789439ffbaec9da2d40985f656491c57b2..56bed9f6e8a9522b3a9d8fa413307498284e4ef7 100644
--- a/config/examples/delta/Dreammaker/Overlord/Configuration.h
+++ b/config/examples/delta/Dreammaker/Overlord/Configuration.h
@@ -1036,7 +1036,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 0, 0, 0.65 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 5
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h
index 4ee8bdb9a98c25819c4ac3f17c9147dc918d0bf6..55d9638b9e5ff2f7e5d31d88657ca4bec421f54c 100644
--- a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h
+++ b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h
@@ -1439,7 +1439,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h
index 94979f58f71d735c3352f5c25a1369181d9e4e2f..07cb576491fb470bdf07a60cc3352cfee79c7fb8 100644
--- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h
+++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h
@@ -1048,7 +1048,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 0, 0, 0.65 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 5
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h
index 774d749bb1bbd21ae7fc4978fae3f0aac411438e..9bbcdcbe33e071a741479387b60f14d0439062a2 100644
--- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h
+++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h
@@ -1440,7 +1440,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/delta/FLSUN/QQ-S/Configuration.h b/config/examples/delta/FLSUN/QQ-S/Configuration.h
index 09ba19da59e8a9f718240e6f2fb7720b241046df..dfb20aef5888c3e8e1f0e8667eb3126c825e3f47 100644
--- a/config/examples/delta/FLSUN/QQ-S/Configuration.h
+++ b/config/examples/delta/FLSUN/QQ-S/Configuration.h
@@ -1038,7 +1038,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 0, 0, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 20
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h b/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h
index de913b7be34b4986691388bd3c96901402e4e231..72efde650cf09d0b97bc49e055a8a3c0ee0910b3 100644
--- a/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h
+++ b/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h
@@ -1440,7 +1440,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
index b842f8ee5b9b243b80987798dd9ab58d53cc4801..d7ce839a94c94cab594bbdf88623c74dcc2cfbb5 100644
--- a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
+++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
@@ -1041,7 +1041,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 0, 0, 0.10 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 20
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
index d76bc56d51e6217ae86233ccad0fc713e6c5c7ea..3d7bf7492edf44299bcfda81e70c4d6135242ca8 100644
--- a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
+++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
@@ -1440,7 +1440,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/delta/FLSUN/kossel/Configuration.h b/config/examples/delta/FLSUN/kossel/Configuration.h
index a4c71e6113e9c1c871f03cf31e16e307b182f003..d222ab463a8aea654d100db1623689c4985ee2b6 100644
--- a/config/examples/delta/FLSUN/kossel/Configuration.h
+++ b/config/examples/delta/FLSUN/kossel/Configuration.h
@@ -1040,7 +1040,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 0, 0, 0.10 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 20
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/config/examples/delta/FLSUN/kossel/Configuration_adv.h
index d76bc56d51e6217ae86233ccad0fc713e6c5c7ea..3d7bf7492edf44299bcfda81e70c4d6135242ca8 100644
--- a/config/examples/delta/FLSUN/kossel/Configuration_adv.h
+++ b/config/examples/delta/FLSUN/kossel/Configuration_adv.h
@@ -1440,7 +1440,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/config/examples/delta/FLSUN/kossel_mini/Configuration.h
index 0db33ff99990bafe089854f142485822ec3fa909..4dfbb1aab6f07b0476d7e5842b229719c002a385 100644
--- a/config/examples/delta/FLSUN/kossel_mini/Configuration.h
+++ b/config/examples/delta/FLSUN/kossel_mini/Configuration.h
@@ -1040,7 +1040,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 0, 0, 0.25 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
index 007d8003c0382e9ca95635b01d86e8b13c565c97..2feca079010c593f4b1b32face2371c890fab8d4 100644
--- a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
+++ b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
@@ -1440,7 +1440,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration.h b/config/examples/delta/Geeetech/Rostock 301/Configuration.h
index d42e985459c00b23a71ab3039c3dd592c69df0fa..dbdfdc7eb1f66c05af39341f95f3d58e99507e16 100644
--- a/config/examples/delta/Geeetech/Rostock 301/Configuration.h
+++ b/config/examples/delta/Geeetech/Rostock 301/Configuration.h
@@ -1028,7 +1028,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 0, -10, -3.5 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h
index 714e8f32e380f55315164ac08ea649f4b17efca6..43bc2294ae43277a6b17d5858ef20f2547247412 100644
--- a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h
+++ b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h
@@ -1440,7 +1440,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/delta/Hatchbox_Alpha/Configuration.h b/config/examples/delta/Hatchbox_Alpha/Configuration.h
index 65e4fcb08e133c93a17658281dcf5ccc391b17dd..6780f2928b91bb887dc6659068e624d0e52fed72 100644
--- a/config/examples/delta/Hatchbox_Alpha/Configuration.h
+++ b/config/examples/delta/Hatchbox_Alpha/Configuration.h
@@ -1043,7 +1043,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 0, 0, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/delta/MKS/SBASE/Configuration.h b/config/examples/delta/MKS/SBASE/Configuration.h
index 231f6e5e75cb647b2ec4879352daaee806aca5fe..b3b0d80af7790c43ed38668da62a7c099f2877b8 100644
--- a/config/examples/delta/MKS/SBASE/Configuration.h
+++ b/config/examples/delta/MKS/SBASE/Configuration.h
@@ -1027,7 +1027,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 0, -10, -3.5 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/delta/MKS/SBASE/Configuration_adv.h b/config/examples/delta/MKS/SBASE/Configuration_adv.h
index 241e216063885b12dd66d1c7b8c7d71472f3e064..214683d0566d7e1fa2b808a60a7d4a6b848b3b22 100644
--- a/config/examples/delta/MKS/SBASE/Configuration_adv.h
+++ b/config/examples/delta/MKS/SBASE/Configuration_adv.h
@@ -1440,7 +1440,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/delta/Tevo Little Monster/Configuration.h b/config/examples/delta/Tevo Little Monster/Configuration.h
index b30054c071431087238b40eeb101e191c32c88d6..ecf4cb147eec79c16dfaf053207c3bc8e76b2c80 100644
--- a/config/examples/delta/Tevo Little Monster/Configuration.h
+++ b/config/examples/delta/Tevo Little Monster/Configuration.h
@@ -1032,7 +1032,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 0, 20, -1.10 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 20
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/delta/Tevo Little Monster/Configuration_adv.h b/config/examples/delta/Tevo Little Monster/Configuration_adv.h
index f44be14081f9eba6ff15176b89a15ce61f27108a..a828d4aa75718d9305d7088c294f7950bb0f7ae3 100644
--- a/config/examples/delta/Tevo Little Monster/Configuration_adv.h
+++ b/config/examples/delta/Tevo Little Monster/Configuration_adv.h
@@ -1440,7 +1440,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/delta/generic/Configuration.h b/config/examples/delta/generic/Configuration.h
index 3312cbcd7c9027a2e77031b251ea9ad3a9790595..df65319cf1c57b26be357e5009817a48ef3f1ed3 100644
--- a/config/examples/delta/generic/Configuration.h
+++ b/config/examples/delta/generic/Configuration.h
@@ -1028,7 +1028,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 0, -10, -3.5 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/delta/generic/Configuration_adv.h b/config/examples/delta/generic/Configuration_adv.h
index 007d8003c0382e9ca95635b01d86e8b13c565c97..2feca079010c593f4b1b32face2371c890fab8d4 100644
--- a/config/examples/delta/generic/Configuration_adv.h
+++ b/config/examples/delta/generic/Configuration_adv.h
@@ -1440,7 +1440,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/delta/kossel_clear/Configuration.h b/config/examples/delta/kossel_clear/Configuration.h
index 7ae934bf1a06c53c1a0882b0dfdac6db734c833d..f6fb09d207ce75a04cd4ffe5ae375f52e873f5a0 100644
--- a/config/examples/delta/kossel_clear/Configuration.h
+++ b/config/examples/delta/kossel_clear/Configuration.h
@@ -1034,7 +1034,8 @@
//BL Touch with John Ecker Custom Mount
#define NOZZLE_TO_PROBE_OFFSET { 0, -29, -3.4 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 1
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/delta/kossel_clear/Configuration_adv.h b/config/examples/delta/kossel_clear/Configuration_adv.h
index f0f3d66a02e519516d171ec31a9a550f5d222480..9fab2a7a27aaeb0cee44e76816a7016dbdb1fba8 100644
--- a/config/examples/delta/kossel_clear/Configuration_adv.h
+++ b/config/examples/delta/kossel_clear/Configuration_adv.h
@@ -1440,7 +1440,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/delta/kossel_mini/Configuration.h b/config/examples/delta/kossel_mini/Configuration.h
index d09738f56b1f4258d80089b7288d722b58e0523a..7b6338aa8d918fa700fead22cccf87021504e494 100644
--- a/config/examples/delta/kossel_mini/Configuration.h
+++ b/config/examples/delta/kossel_mini/Configuration.h
@@ -1030,7 +1030,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 0, -10, -3.5 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/delta/kossel_mini/Configuration_adv.h b/config/examples/delta/kossel_mini/Configuration_adv.h
index 007d8003c0382e9ca95635b01d86e8b13c565c97..2feca079010c593f4b1b32face2371c890fab8d4 100644
--- a/config/examples/delta/kossel_mini/Configuration_adv.h
+++ b/config/examples/delta/kossel_mini/Configuration_adv.h
@@ -1440,7 +1440,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/delta/kossel_pro/Configuration.h b/config/examples/delta/kossel_pro/Configuration.h
index 20d57e571fedeea99cb9de02f806d5376ad22e0f..eaf46fc3899bc29583d9bfa09768a6ffffebb18f 100644
--- a/config/examples/delta/kossel_pro/Configuration.h
+++ b/config/examples/delta/kossel_pro/Configuration.h
@@ -1029,7 +1029,8 @@
* not giving someone a head crash. Use something like G29 Z-0.2 to adjust as needed.
*/
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/delta/kossel_xl/Configuration.h b/config/examples/delta/kossel_xl/Configuration.h
index 0ad3f64be71b51772e8d0be88874ed9a502af18b..9119419e4f7a3dbbc8ac016634158ecffb4b7e49 100644
--- a/config/examples/delta/kossel_xl/Configuration.h
+++ b/config/examples/delta/kossel_xl/Configuration.h
@@ -1031,7 +1031,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 0.0, 0.0, 0.3 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/delta/kossel_xl/Configuration_adv.h b/config/examples/delta/kossel_xl/Configuration_adv.h
index 85a94160388ac8bad41d33b5af24a934baaa9cdb..f6031b7285cac7c7506d59bcb0a2d35e0c058243 100644
--- a/config/examples/delta/kossel_xl/Configuration_adv.h
+++ b/config/examples/delta/kossel_xl/Configuration_adv.h
@@ -1440,7 +1440,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/gCreate/gMax1.5+/Configuration.h b/config/examples/gCreate/gMax1.5+/Configuration.h
index 05be303ecca28a5792f7368cdb5279714b18d5b2..5823806380068783bfeff39257bba1846a76ae4f 100644
--- a/config/examples/gCreate/gMax1.5+/Configuration.h
+++ b/config/examples/gCreate/gMax1.5+/Configuration.h
@@ -942,7 +942,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -17, -10, -0.25 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 45
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/config/examples/gCreate/gMax1.5+/Configuration_adv.h
index 4c8519fcca322c92590c8547b3c481434e8baacc..d79c6586d0e514a618baa19f184756155492a579 100644
--- a/config/examples/gCreate/gMax1.5+/Configuration_adv.h
+++ b/config/examples/gCreate/gMax1.5+/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/makibox/Configuration.h b/config/examples/makibox/Configuration.h
index 3d4fbaa1f13d8c02975d0ed80125389ca76d35d2..9bb50e352ead9a49c007eb4f9edea84062ed1d0f 100644
--- a/config/examples/makibox/Configuration.h
+++ b/config/examples/makibox/Configuration.h
@@ -932,7 +932,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -25, -29, -12.35 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/makibox/Configuration_adv.h b/config/examples/makibox/Configuration_adv.h
index 7dc28522a17b8d582dbf7f69950314cda19b3b91..170eda1663de1953942f6664ef65c15f65331730 100644
--- a/config/examples/makibox/Configuration_adv.h
+++ b/config/examples/makibox/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/tvrrug/Round2/Configuration.h b/config/examples/tvrrug/Round2/Configuration.h
index d0f8637c9fdc8b617324724c1ac9e78acb099c17..60fea65b8af7a027bb556db61c2b6a786510f66f 100644
--- a/config/examples/tvrrug/Round2/Configuration.h
+++ b/config/examples/tvrrug/Round2/Configuration.h
@@ -924,7 +924,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { -25, -29, -12.35 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/tvrrug/Round2/Configuration_adv.h b/config/examples/tvrrug/Round2/Configuration_adv.h
index b9bb0751e4f3fa18be26540477dca3740791b5c2..0a8214c25147e96e85273e44379a3479815ab6b1 100644
--- a/config/examples/tvrrug/Round2/Configuration_adv.h
+++ b/config/examples/tvrrug/Round2/Configuration_adv.h
@@ -1438,7 +1438,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
diff --git a/config/examples/wt150/Configuration.h b/config/examples/wt150/Configuration.h
index ac8122168234535db0560e657abd7c11f272f355..8b3c46f6651a791906dc98ccfc8eb1184a085021 100644
--- a/config/examples/wt150/Configuration.h
+++ b/config/examples/wt150/Configuration.h
@@ -934,7 +934,8 @@
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
-// Certain types of probes need to stay away from edges
+// Most probes should stay away from the edges of the bed, but
+// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
diff --git a/config/examples/wt150/Configuration_adv.h b/config/examples/wt150/Configuration_adv.h
index 965972ca3bf5de3980670f93f68f8a536898f3f5..dab116d114ed9ca85d61d3d60f7e2641922ae0ec 100644
--- a/config/examples/wt150/Configuration_adv.h
+++ b/config/examples/wt150/Configuration_adv.h
@@ -1439,7 +1439,8 @@
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
- * sides of the bed.
+ * sides of the bed. With NOZZLE_AS_PROBE negative values are
+ * allowed, to permit probing outside the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over